User Manual

• Resolution: Setting video resolution of footage recorded,
Front camera only: 1920*1080P 60FPS, 1920*1080P 30FPS
Front + Rear Camera: 1920*1080P 30FPS
• Bitrate: You can set the bitrate for video. High bitrate may improve
the quality and smoothness of the video, especially when recording
fast motion or high contrast scenes. Using high bitrate mode may
decrease the amount of recording time available on your memory
card. Using low bitrate will save space and record for longer time.
• Live Video Source: Front camera / Rear camera / PIP mode 1 / PIP
mode 2.
• Loop Recording: O / 1 / 2 / 3 / 5 / 10 minutes.
Recording will begin automatically after powering on with a micro
SD card in the device. Each recorded file is up to three minutes long,
with old footage being replaced when micro SD card storage is full.
• WDR (Wide Dynamic Range): Dynamic range is the ratio of the
brightest portion of the image to the darkest portion of the image.
WDR enables the camera to deliver video with near perfect exposure
in varying lighting situations.
• Exposure: Adjusting the value of the EV (Exposure Value) properly
can create better footage under dierent light sources. It ranges from
-2.0 to +2.0. You can adjust the EV for front and rear camera
separately. Default is set at 0.0.
• Parking Mode: There are 3 options under parking mode:
① Auto Event Detection
The camera will automatically record for 1 minute while a moving
object is detected while car is parked and will stop recording if no new
movement.
② Time Lapse recording
Time lapse record a video at low frames at 1 / 2 / 3 / 5 / 10 / 15 fps, It
keeps recording continuously without audio recorded.
③ Low Bitrate Recording
This mode record video in low bitrate 4MB/s for both front and rear.
It keeps recording continuously in mini le size with audio recorded.
Note: We recommend to buy VIOFO HK3 ACC hardwire kit cable for
parking mode recording.
• Parking Recording Timer: Set the parking recording duration.
• Time-lapse Recording: Record video from frames captured at
specific time intervals to conserve memory and reduce the time it
takes to review video. The default is o.
• Motion Detection: When activated, the camera will start recording if
there is movement in front of the camera. Once the camera does not
detect movement for 60 seconds, it stops recording and returns to
“Motion Detection” mode. The camera will record again in the time of
detecting a new movement.
• GPS: Turn on / o GPS logger. A GPS module is used to include the
location data in the recorded videos. If disabled, your camera will no
longer measure your speed and position; nor synchronize the time /
date. (Only available when connect with GPS signal) Please use
Setting Setting
21 22
“Dashcam Viewer” to playback videos and to visualize your position
and speed on your computer.
• Speed Unit: Kilometer per hour (KMH) and miles per hour (MPH) are
available for speed unit.
• G-Sensor: The G-sensor measures shock forces and locks the video
recorded at the time. The settings from “low to high” determine the
amount of force needed to lock the file from being overwritten. We
recommend that you set it at low.
• Wi-Fi: Set it On / O. Press the [ ] button for 3 or 5 seconds to
enable Wi-Fi quickly. We recommend to choose 5GHz Wi-Fi mode.
• Date Stamp: Imprint the time and date on the recorded video.
• GPS Info Stamp: Imprint the GPS information on the recorded video.
• Camera Model Stamp: Imprint the camera model on the recorded
video.
• Record Audio: Turn on and o the microphone. This can also be
changed during recording by pressing the microphone button [ ].
• Screen Saver: The screen goes black by default after 3 minutes while
recording. You can set it by adjusting dierent time intervals on menu.
• Boot delay: The camera will boot seconds later when powered on.
The settings are O / 5s / 10s.
• Date / Time: Set system date / time.
• Time Zone: Set the current time zone for GPS time and date
calibration.
Note: the time zone must be manually adjusted for daylight savings.
• Language: Set the on-screen display to English, Traditional Chinese,
and French, etc.
• Beep Sound: Turn all notification sounds On / O.
• Frequency: Set it to minimize flickering and banding in the recorded
video.
• Image Rotation: Turn the screen upside down. It’s fit for both front
and rear camera.
• Rear Camera Mirror: Rear Camera Mirror can make the image of the
rear camera to be displayed and recorded as reversed compared to the
actual view, you can set the setting On / O.
• Format: The operation will delete all data on the Micro SD card.
Note: Once you format the card, all information will be deleted and
unrecoverable. Make sure to back up all files that you needed before
formatting.
• Format Warning: Set the number of days between format warnings.
• Default Setting: Restore device to factory settings.
• Car Number: Imprint the car number on the recorded video.
• Custom Text Stamp: Imprint the customize text on the recorded
video.
• Firmware Version: Check the current firmware version of the
camera.