The company behind Viper® Auto Security Systems is Directed. Vista, CA 92081 www.viper.com Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security products and accessories available. The recipient of nearly 100 pat® ents and Innovations Awards in the field of advanced electronic technology. Quality Directed products are sold and serviced throughout North America and around the world.
Congratulations Congratulations on the purchase of your state-of-the-art security system. Reading this Owner’s Guide prior to using your system will help maximize the use of your system and its many features. For more information please visit the below website: http://www.viper.com – For general and additional guide information. For any additional questions please contact your authorized Directed dealer or contact Directed at 1-800-753-0600. (U.S.
Important information Government Regulations and Safety information Read the Government Regulations and Warning! Safety First sections of this manual prior to operating this system. Your Warranty Your system comes with a warranty. Please make sure you receive the warranty registration card and proof of purchase from your dealer indicating the product was installed by an authorized Directed dealer. You can validate it online at www.prodregister.
Contents 1-way remote control .......................................................................................... 3 Control Center..................................................................................... 4 Remote control command table .............................................................. 5 Three- button remote configuration ......................................................... 5 Remote control functions .........................................................................
Battery Information ............................................................................................ 30 Battery Replacement........................................................................... 30 Battery Disposal ................................................................................ 30 Glossary of Terms.............................................................................................. 31 Government Regulations ...........................................................
1-way remote control Internal antenna Transmit LED Command Buttons Feature Description Internal Antenna Used for transmitting information Transmit LED Active when transmitting information Command buttons (4) Used to perform locking, unlocking, arming and disarmig, auxiliary channel and panic activation. © 2012 Directed. All rights reserved.
Control Center Control button Antenna Status LED The Control Center, typically located on the upper part of the front windshield. It consists of: s s s The In-vehicle system antenna. The Status LED, as a visual indicator of the system’s status. The Control button, for placing the system into Valet Mode* and to perform the Emergency Override* operation. * See Valet Mode and Disarming without a Transmitter in the “Using your System” section of this guide. 4 © 2012 Directed. All rights reserved.
Remote control command table Feature Description Lock the doors and arm the vehicle Unlock the doors and disarm the vehicle AUX Activate Silent Mode and Auxilairy functions Panic Press together to control an Auxiliary output and Three- button remote configuration This system may be used with an optional 3-button remote, which is available for purchased through your authorized Directed dealer. The table below describes the basic 3-button functions.
Remote control functions The remote control buttons are used to send commands to the system.The descriptions below reflect the standard configuration for this system. The buttons can be custom configured for the user’s specific needs by the installer. Arm Press and release . Doors lock and system is armed. Disarm Press and release . The doors unlock and system is disarmed. AUX Press and release AUX Silent mode and an optional auxilairy function are controlled by pressing this button.
Using your system Active arming You can activate or arm the system by pressing for one second. When the system arms you will hear a short siren sound or chirp, and the parking lights flash once. If the vehicle’s power door locks have been connected to the system, the doors lock. While the system is armed the status LED flashes once per second, indicating that the system is active and protecting your vehicle.
When the system is armed: s Light impacts trigger the Warn Away® signal. When triggered,the siren chirps and the parking lights flash for a few seconds. 8 s Heavy impacts trip a Triggered Sequence. The sequence consists of the siren sounding continuously and the parking lights flashing for a pre-programmed period, which can range in duration from 1 to 180 seconds. s If a door is opened, the system will immediately start chirping the siren and flashing the parking lights.
Multi-level security arming Multi-Level Security Arming allows you to select which of the security system’s inputs or sensors are active, or are bypassed when the system is armed. (See the Table of Zones section of this guide) Press one time to arm the system, siren chirps one time. Pressing again activates Multi-Level Security Arming.
Arming while driving Your system can be armed while driving the vehicle. Press on your transmitter for two seconds while the vehicle is running or while the ignition is on. The siren chirps once, and then once more indicating that the ignition is on. The security system does not respond to any input except the door triggers and the Failsafe® Starter Kill (if installed) will not activate. The security system disarms automatically when the ignition is turned off.
High Security Disarm High Security Disarm makes it possible to silence and reset the system when it is triggering, without disarming. If the system is triggered, and the siren sounds for longer than six seconds, pressing will stop the trigger and return the system to an armed state. The system does not disarm, but rather reset. This prevents you from disabling the system should you want to disarm without visually checking the vehicle. Pressing again after resetting the system, will disarm the system.
Location of Valet Button_________________________________ Number of Pulses______________________________________ The unit responds to one to five pulses of the Valet button when disarming. Check with your installer to discuss how you want the system configured. Note: As a precaution, if programmed for passive arming the system should be placed into Valet Mode until a remote is available. Dome light control Security only The dome light activates for 30 - seconds after the system is disarmed.
Panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your remote. Press for approximately two seconds, to enter Panic Mode. The siren sounds and the parking lights flash for the programmed siren duration. To stop Panic Mode at any time, press the . Valet mode You can prevent your security system from automatically arming and triggering by using Valet Mode. This is very useful when washing the vehicle or having it serviced.
Nuisance prevention circuitry Your system has Directed’s Nuisance Prevention Circuitry (NPC). It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder, jackhammers, or airport noise. For example, if the alarm triggers three times within a 60- minute period and each time the same sensor or switch triggers the alarm, NPC will interpret those triggers as false alarms.
Auxiliary outputs This system also supplies outputs that can control convenience options such as remote control trunk release and window automation. Consult your dealer for available options for your system. Channel 2 Trunk release: When connected, pressing AUX for 1.5 seconds will remotely release the vehicle trunk lid. Channel 3 auxiliary output: When connected, pressing and will immediately activate this output to control an additional convenience option.
Arming diagnostics If the system is armed while an input is active - door open, sensor triggering - the unit chirps once when arming and then one more time a few seconds later. This is called Bypass Notification. Bypass Notification does not occur when using Silent Mode or if chirps have been programmed OFF. The security system continually ignores the zone that was active until the input stops. Three seconds after the input stops, the system monitors that input normally.
System status chirps The siren chirps when arming/disarming the system. The pattern of chirps audibly report the system’s status as described below. Action Chirps Description Arm 1 System armed Arm 3-second delay, 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC active Table of zones The zone number is the number of LED flashes used by the system to identify that input.
Interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics. If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the in-vehicle status LED. Active or triggered zones will be indicated by a pattern of blinks by this LED. For Example: If Zone 3 was active or triggered, the in-vehicle LED will blink three times with a two-second pause. Then it will blink three times again, and repeat until the ignition is turned on.
installed, the system can never inadvertently stop your vehicle in traffic or on railroad tracks while the vehicle is in operation. It is unlike other systems that shut down your engine while it is running. This system is designed to perform starter interrupt, or starter kill. The Failsafe Starter Kill cannot shut down an already-running engine – it can only prevent an engine from starting in the first place.
Triggered sequence, VRS Fifteen seconds after the last door has closed, the in-vehicle LED will begin flashing. This delay is intended to allow you time to distance yourself from your vehicle in the event of a carjacking. Forty-five seconds later, the siren begins chirping and the parking lights begin flashing. This time could be used to notify authorities that your vehicle has been hijacked, and tell them what the VRS will do next.
Disarming the VRS Take the time to familiarize yourself with the VRS triggering sequence and the disarm procedure. It is important to recognize and identify the VRS trigger sequence and know how to disarm it in case of accidental activation. Once the VRS is armed, it does not disarm automatically. You must disarm it the next time you operate the vehicle. You must disarm it with one of the following procedures: If the system has not entered the triggered sequence (siren has not started chirping): 1.
Code hopping The receiver and transmitters each use mathematical formulas called algorithms to change their codes each time the transmitter is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep the transmitter “in sync” with the control unit even if you use the remote control out of range of the vehicle.
Rapid resume logic This Directed system will store its current state to non-volatile memory. If power is lost and then reconnected, the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, VRS, and Valet Mode.
Programming options Programming options control what your system does during normal operation, and require few or no additional parts. However, some may require additional installation labor. The following is a list of the program settings, with the factory settings in Bold: s Active arming (only with the remote) or passive arming (automatic arming 30- seconds after the last door has been closed).
s Panic mode enabled/disabled with the ignition on: Some states have laws against siren capability in a moving vehicle. s Forced passive arming On or off: If your system is programmed for passive arming and the forced passive arming feature has been programmed on, the system will passively arm after one hour, even if a protected entry has been left open. This feature is useful if a door has been left ajar when leaving the vehicle.
s Full trigger response 30 or 60 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance. If your installer is programming the security system with the Directed Bitwriter, the full triggered response can be programmed for any duration ranging from 1 to 180 seconds.
Installation options The system has many options that may require extra parts and labor. Some of the possibilities are listed here. s Progressive unlocking: In most cars with electric power door locks, the system can be configured so that when the system is disarmed, only the driver’s door unlocks. A second press of the button unlocks the other doors. s Vehicle Recovery System, (VRS): It is an anti-carjacking device designed to help in the safe recovery of your vehicle in case of a carjacking.
Security & Convenience Expansions Listed are some of the many expansion options available. Please contact your dealer to find out about all the convenience options available to you. Audio Sensor: Metal on glass, cracking glass, and breaking glass each produce distinctive acoustic signatures. The 506T audio sensor uses a microphone to pick up sounds, and then using proprietary acoustic software, analyzes the sounds to determine if the glass was struck.
Power Window Control: Automatic power window control is provided with the 529T and 530T systems. Tilt Sensor: The 507M tilt sensor can be added to your system to protect your car when its parked. An alarm is triggered if the vehicle is lifted, to protect expensive rims. Remote Start System: For the ultimate in convenience, A Directed remote start system can start your vehicle, monitor engine functions, and power your climate control system with a push of a button.
Battery Information The remote controls are powered by a pair of 3V (CR-2016) batteries that can be purchased at most retailers. When the battery begins to weaken, the operating range will be reduced. Battery Replacement Side View Slot 1. Using a small flat-headed screwdriver, insert into slot located on the side of the remote control and carefully pry open the unit. 2. Turn unit over and carefully remove the rear housing. Remove the batteries from holder and replace with a new one.
Glossary of Terms Document Terminology ASK Amplitude Shift Keying—a method of transmitting data. 1-way Remote Control A hand-held remote control, also called transmitter that operates the various functions of your system but does not provide message display.. Control Button (Valet Switch) A small push button located on your system’s control center. It is used to override (disarm) the system when a remote is not available or to enter/exit valet mode Control Module (unit) The “brain” of your system.
Document Terminology 32 Warn Away® Lighter impacts to the vehicle generate a Warning Zone response, several seconds of siren chirps and parking light flashes. Zone Input that the alarm recognizes as unique. Each input is connected to a particular zone. Two or more inputs may share the same zone. © 2012 Directed. All rights reserved.
Patent Information This product is covered by one or more of the following United States patents: Vehicle Security Patents 5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591; 5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484 Remote Start 5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053; 7,483,783 Other patents pending © 2012 Directed. All rights reserved.
Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
Receiver antenna To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance. This device complies with the Industry Canada Radio Standards Specification RSS 210.
Limited lifetime consumer warranty Directed Electronics.
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT.
38 © 2012 Directed. All rights reserved.
The company behind Viper® Auto Security Systems is Directed. Vista, CA 92081 www.viper.com Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security products and accessories available. The recipient of nearly 100 pat® ents and Innovations Awards in the field of advanced electronic technology. Quality Directed products are sold and serviced throughout North America and around the world.
Quick Reference Install Guide Vehicle Security System Models 3105 and 3305 Wiring Connections Programming Port: The 998T Bitwriter can be connected to this port for programming feature options. SmartStart can be connected to this port to operate the system by Smartphone.
Programming System Features The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the feature settings using the Valet switch/Control button.* *Depending on which model is installed, the system uses either an external Valet switch and an external Status LED or a Control Center with an onboard Control button (Valet Switch) and Status LED. 1. 2. 3. 4. 5. 6. Open a door. Turn the ignition on, then off. Select a Menu.