Models Viper 5101 Clifford 1.2 Python 1401 Keyless Entry and Remote Start Installation Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
Bitwriter®, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics. The Bitwriter® (p/n 998U) requires chip version 2.7 or newer to program this unit. Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M).
Contents Warning! safety first......................................................................................................................... 4 Wiring Diagram.............................................................................................................................. 5 Wiring Connections......................................................................................................................... 6 Main Harness (H1), 12-pin connector......................................
Warning! safety first • • The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed Electronics dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.
Valet switch Control button LED Status LED Control Center Wiring Diagram er LED Status LED Control Center Control Center 6111T Control Center + - Horn Input Polarity Jumper D2D jumpers; Factory setting is horizontal position. Most Xpresskit modules use this setting, check the Xpresskit installation guide for the specific setting.
Xpresskit installation guide for the specific setting.
To change jumper settings 12 TACH threshold OFF: TACH threshold ON: 1 1 1 NOTE: Pin 1 is on the left 10 9 8 7 6 5 4 3 2 1 8 7 6 10 5 Bitwriter Neutral Safety Remote 4 3 2 Port 8 Switch Start In 1 Remote Start, (H3) 8-pin connector 5 Door Lock/ Unlock Output H2 Port H3/1 PINK 1 H3/2 RED/WHITE 1 H3/3 ORANGE 18 H3/4 VIOLET 9 H3/5 RED +12V FUSED (30A) IGNITION 1 INPUT H3/6 PINK/WHITE IGNITION 2/FLEX RELAY OUTPUT H3/7 PINK/BLACK 1 10(IF REQUIRED) OF FLEX RELAY FLEX RELA
remote start is interfaced before this switch, it will provide protection from starting in gear. However, some vehicles combine the column shift mechanism and the mechanical neutral safety switch into one mechanical part. Important: You must complete the remote start system installation before doing the following test. Ensure that the remote start system is functioning normally. This includes connecting to the brake as a shut-down. Testing the neutral safety switch 1. 2. 3. 4. 5. 6.
Startup Diagnostics: If the vehicle fails to activate the remote start, the remote start module will flash the parking lights on the vehicle to notify you of what caused the no-start situation. Parking Light Flashes 5 flashes 6 flashes 7 flashes 8 flashes Brake wire is active Hood pin wire is active Manual transmission mode is enabled and not initialized. Neutral safety wire has no ground or the neutral safety switch is Off.
Programming System Features The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the feature settings using the Control button. 1. Turn the ignition on, then off. 2. Select a Menu. Press and hold the Control button. The number of LED flashes and horn honks indicates the menu number. 1 LED flash and honk indicates menu 1, 2 LED flashes and honks - menu 2 and 3 LED flashes and honks for menu 3. 3.
Feature Menus Default settings are Opt. 1 (in bolder type). New features are bold with grey background. Menu 1 - Vehicle integration Menu Item Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt.
3. Double Lock Only: the lock output only will pulse twice 4. Double Lock & Unlock: the lock & unlock outputs will pulse twice 6. Door Lock Output Duration 1. 0.8sec.: the door lock output pulses will be 800mS in duration 2. 3.5sec.: the door lock pulses will be 3.5 seconds in duration 3. 0.4 sec.: the door lock pulses will be 400mS in duration 7. Ignition Controlled 2nd Unlock 1. After first unlock: for Ign-controlled unlocking, the 2nd unlock will activate 800mS after the first (driver door) unlock 2.
Menu 2 - Convenience Menu Item 1 Feature Opt. 1 Opt. 2 One-time Bypass No Bypass Bypass Opt. 3 Opt.4 Opt.
(Blue) wire 2. Before Unlock: the OEM Alarm Disarm wire will pulse as programmed before the unlock wire 3. Remote start only: the OEM Alarm Disarm wire will pulse as programmed during remote start only 7. OEM Alarm Disarm Pulses (H2/1 wire) 1. 1: the OEM Alarm Disarm wire will pulse once per operation 2. 2: the OEM Alarm Disarm wire will pulse twice per operation 8. Aux 1 Output Type (H2/6 wire) 1. Validity: when the Aux command is received the wire will turn on and remain on until the command ceases 2.
Menu 3 - Remote start Menu Item Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 1 Transmission Mode Manual* Automatic 2 Engine Checking Mode Virtual Tach 3 Cranking Time 0.6 sec. Voltage Off Tachometer 0.8 sec. 1.0 sec. 1.2 sec. 1.4 (5)/ 1.6 (6)/ 1.8 (7) 2.0 (8)/ 4.0 (9) 60 min. On- 10 min. 4 Remote Start Runtime 12 min. 24 min. 5 Activation Pulse Count 1 2 6 Turbo Mode No Turbo Mode On-1 min. On-3 min. On-5 min. 7 Timer Mode Runtime 12 min. 3 min. 6 min. 9 min.
activate and de-activate remote start 6. Turbo Mode 1. No turbo Mode: Turbo mode is not available 2. On – 1/3/5/10 minutes: Turbo Mode is available and, when activated, the engine will run for the duration set per the selected option 7. Timer Mode Runtime • 12/3/6/9 minutes: sets the runtime when the engine is started by the Timer Mode and SmartStart features 8. Flex 1. 2. 3.
16. Remote start Safelock 1. Off: the Door lock and Factory Alarm Re-arm outputs will maintain the current status (locked/unlocked) during remote start and after shut down 2. On: the Door lock and Factory Alarm Re-arm outputs will arm/lock the vehicle during remote start and after shutdown Bitwriter - Only Options If programming with the Bitwriter®, the learn routine can be locked or unlocked.
1. Aux/Trunk Icon Type: sets the name to be displayed in the Text Field when the Aux/Trunk output is activated/de-activated 2. Aux 1 Timed Output: sets the output duration in 1 second intervals up to 90 seconds for Aux 1 3. Aux 1 Icon Type: sets the name to be displayed in the Text Field when the Aux 1 output is activated/ de-activated 4. Aux 2 Timed Output: sets the Aux 2 “Timed” output in 1 second intervals up to 90 seconds 5.
Basic Remote Functions See Owner’s guide for functionality details on the 1-way remote controls. Reset and Deletion If a feature/virtual tach needs to be reset or the remote controls need to be deleted, use the following procedure. 1. Turn the ignition to the ON position (The heavy gauge pink wire must be connected). 2. Within 10 seconds, press and release the Control button: 2 times if you want to delete remotes, 3 times to reset features or 4 times to reset virtual tach..
Troubleshooting: Keyless Entry System does not Auto re-lock: 1. Is Auto re-locking programmed ON? 2. Are the door inputs connected? Either the H1/8 green or the H1/6 violet should be connected. Door locks operate backwards. • This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have reversed these. Troubleshooting: Remote Start The remote will not activate the remote start 1. Check remote startup diagnostics. 2. Is the neutral safety switch plugged in and turned on? 3.
1. Is the system programmed for engine checking off or virtual tach voltage sense? When programmed for either of these features, the engine cranks for the pre programmed crank time regardless of how long it takes for the vehicle to actually start. Adjust to a lower cranking time. 2. Was the Tach Learn successful? The LED must light solid and bright to indicate a successful learn. 3. Make sure that there is a tach signal at the purple/white tach input wire of the remote start.
around. • 22 The E-brake wire connected to the neutral safety input of the system has a poor ground. Clean the contacts on the switch or replace the switch. © 2009 Directed Electronics. All rights reserved.
