Model 7900 ➤Owner’s Guide
limited lifetime consumer warranty Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and servi
REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
table of contents limited‑lifetime‑consumer‑warranty �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � i what‑is‑included �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� 3 important‑information �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��
code‑hopping �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �42 owner‑recognition‑ �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �43 rapid‑resume‑logic �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��
what is included ➤ A control module ➤ A Responder receiver/antenna ➤ One 2-way Color Remote Control P/N 7541V ➤ A Stinger Doubleguard shock sensor ➤ A 514N Neosiren ➤ The plug-in status LED ➤ The plug-in Valet/Program switch ➤ A hood pinswitch ➤ A toggle (override) switch ➤ One Remote Control charger important information Congratulations on the purchase of your combination remote start alarm system.
➜ your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Make sure you receive the warranty registration from your dealer. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. ➜ fcc/id notice This device complies with Part 15 of FCC rules.
safety ➜ important safety instructions 1. Follow all instructions. 2. Do not use this apparatus near water. 3. Clean only with a dry cloth. 4. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 6.
CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SEVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
replacement remote controls You can purchase replacement remote controls from your Authorized Dealer or on-line at the following web site: www.directedstore.com Once you receive your new remote control, please refer to instructions included on the remote packaging. remote control introduction This 2way Remote Control system operates at 434MHz using binary data communication technology for sending and receiving of information.
• 12 Hour Clock • Remote control battery level indicator • Power saver sleep mode • Beeps on/off • Page Mode on/off • Programmable alarm trigger animations & icons • 2way garage door module capable note: for detail on setting the clock and programming of other remote control features, refer to the remote control programming section in this manual.
1. ARM & DISARM ICON 2. SENSOR WARN TRIGGER & CAR CALL ICONS 3. HOOD TRIGGER ICON 4. TRUNK OR HOOD ICONS (PROGRAMMABLE) 5. IGNITION TRIGGER ICON 6. ARM/LOCK BUTTON 7. AUXILIARY CHANNEL BUTTON 8. TRANSMITTER PROGRAMMING BUTTON (ON REAR) 9. REMOTE START BUTTON 10. DISARM/UNLOCK BUTTON 11. REMOTE START ON/OFF ICON 12. REMOTE CONTOL BEEPS ON/OFF ICON 13. SENSOR ZONE TRIGGER ICON 14. FULL TRIGGER FOR ALL ZONES & CAR CALL ICONS 15. REMOTE CONTROL BATTERY LEVEL INDICATOR ICON 16.
remote control button functions The remote control buttons are initially programmed to Standard Configuration for this system. The instructions in this manual correspond to a Standard Configuration remote control. NOTE: If desired, the remote control button configuration can be customized by an authorized dealer. ➜ standard configuration Button This button controls the arm, lock and panic functions. Button ������� This button controls the disarm, unlock and panic off functions.
and ������� Buttons These buttons control the turbo timer/short run remote start function. ������� and Buttons These buttons control the auxiliary channel 4 output. ������� ������� and Buttons These buttons control the auxiliary channel 5 output. ������� and ������� and Buttons These buttons control the rear window defogger function. and ������� Buttons These buttons control the auxiliary channel 6 output.
Note: If the remote control does not play the transmitting anima‑ tion, the remote control did not transmit the command. • Command response: one second after the system receives and implements a command; it will transmit a command response to the activating remote control. The remote control will play the appropriate Notification output. Note: If more than one remote control is programmed to the system, a command update will follow ten seconds later.
• Alarm Page Alert: an alarm page alert is a single beep that repeats every sixty seconds after an alarm warn or full trigger page has been received. It will continue to beep until it has been cleared by the user. • Alarm Page: to clear an Alarm Page Alert, press any button on the remote control. Until the alert is cleared, the buttons on the remote control will not transmit commands. a.
To replay, simultaneously press and release the “ ”&“ ” buttons. The screen will replay the animation once without beeps. remote control maintenance ������� This remote control needs no specific maintenance beyond charging of the remote control battery. It is powered by a 4.3V/600mA Lithium Ion battery that will last approximately 1 week on a full charge under normal use. Excessive viewing of on-screen animations will quickly diminish the battery charge.
using your system ➜ warning! safety first The following safety warnings must be observed at all times: ➤ Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. ➤ When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage).
injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in the product installation guide.
AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
➜ active arming Press the button of the remote control for 1 second to arm the alarm. “system” The siren will chirp once, the lights will flash once, the ������� doors will lock if connected, and the led will begin flashing. “remote” The remote control Notification will be one beep, play the arm animation and then display the status icons for 6 seconds. note: In Valet mode, when locking the doors, the remote control Notification will be a single beep and the Valet mode animation.
➜ passive arming This alarm can be programmed to arm automatically thirty seconds after exiting the vehicle. The following steps will start the passive arming operation. • Turn the ignition off, exit the vehicle and close all protected entries (doors, hood and trunk). • The led will flash rapidly to indicate the alarm will arm shortly. “system” After twenty seconds the siren will chirp once. Ten seconds later the lights will flash when the alarm is armed.
while exterior protection is provided via dual stage shock sensor. Entry point protection is provided by connection to the vehicle wiring system and engine immobilization is provided by a hidden starter kill relay. Alarm triggers will activate the siren and lights to draw atten‑ tion to any trigger event and immediately send an Alarm Page to the remote control. The remote control will play an Alarm Page Notification that consists of beeps and animation to inform you of the trigger event.
“remote” The remote control Notification will consist of four beeps twice followed by the Shock Sensor animation. This will repeat 3 times before displaying the status icons. note: the animation displayed for Full trigger Notifications can be changed to accommodate any additional system sensors. exterior protection The dual stage shock sensor monitors impacts to the vehicle exte‑ rior and will activate a response to the severity of the impact.
hood and Trunk triggers responses “system” The alarm will immediately activate the full trigger response. “remote” The remote control Notification will include the Hood or Trunk animation and hood or trunk icon. interior protection If the vehicle has been entered and the ignition turned on, the starter kill will prevent the engine from starting.
➜ multi-level arming Multi-level arming allows you to choose the level of vehicle protection each time the alarm is armed. It is also a convenient way to avoid sensor triggers when parking in environmentally questionable areas such as airports, construction zones or during inclement weather. After arming, if within 1 second the system receives arm signals from the remote control it will chirp the siren and bypass selected zones for each signal. ➤ First ➤ Second press: one chirp, the alarm is armed.
➜ arming while driving The alarm can be armed while driving to protect the occupants from unwanted entries or carjacking attempts in undesirable locations. While armed, the alarm will trigger if a door is opened and the starter kill will not be activated. to arm while driving Press and hold the button for 2 seconds “system” The system will chirp once and then once more to indi‑ cate that the ignition is on. ������� “remote” The remote control Notification will be the arm animation.
➜ disarming Press the button of the remote control for 1 second to disarm the alarm. ������� “system” The siren will chirp twice, the lights will flash twice, the doors will unlock if connected, and the led will stop flashing. “remote” The remote control Notification will be two beeps, play the disarm animation and then display the status icons.
➜ disarming without a remote control If your remote control should be lost, damaged or fail to operate the system, the ignition and Valet Switch can be used to disarm the alarm. You must know where the Valet Switch is located and the correct number of presses required for the alarm to disarm. Have your installer familiarize you with this procedure. The siren will be sounding while you are disarming which can be quite distracting. 1. Open the driver’s door and enter the vehicle. 2.
➜ silent mode Use Silent mode to temporarily delete arming or disarming siren chirps when operating the system at a time where silent operation is desired. Silent mode when arming also deletes the Warn-away response of the alarm system. note: Although the Warn-away function is deleted, Full triggers of the alarm are still responded to normally using silent mode Press the button for less than one second immediately before pressing the or buttons.
To stop Panic mode press and release the or button, or wait for the siren duration to end. The siren and light flash output ������� will cease and the alarm will return to the armed state. ������� “system” The system will activate the full trigger output. It will sound the siren and flash the lights for the programmed siren duration. “remote” When Panic mode is activated the remote control Notification will be the Panic mode animation.
“remote” When exiting Valet mode, the remote control Notification will be two beeps and the Disarm animation. Use the following methods to enter and exit Valet mode. valet switch: a. Turn the ignition on for 5 seconds b. Turn the ignition off c. Within 10 seconds press and release the Valet switch once d. The led will turn on when entering and off when exiting Valet mode DRW-35 remote control: 1. Open any door. 2. Press button, the system will arm. 3.
➜ auxiliary channels This system includes four additional auxiliary channel outputs that can be programmed to control any number of vehicle systems and aftermarket add-on accessory modules. Trunk release, power seats, power windows and sunroof, amp racks and audio/video systems can all be controlled at the touch of a remote control button. activate an auxiliary channel Refer to Remote Control Button Functions section of this guide on which remote control buttons will activate an auxiliary channel. a.
➜ remote start functions This system includes several ways to utilize the remote start feature for your convenience and comfort when driving or parked, while still maintaining a high level of vehicle security. • remote start is used to warm the engine and control the interior temperature for entering and driving the vehicle. • valet takeover activates remote start while the engine is running to maintain the vehicle interior temperature during short trips away from the vehicle.
b. The lights will flash as confirmation the remote start command was received. c. The system will send a remote start response to the remote control. d. A few seconds later the engine will start. For diesel vehicles there may be a delay for the glow plugs to warm. e. Once started, the engine will run for the programmed run time and the lights will continue to flash or turn on. “remote” The remote control Notification will be two beeps ascending in tone followed by the remote start animation.
d. Toggle the shutdown switch to off e. The run time expires “system” a. The lights will turn off. b. The engine will turn off (except when the key is on) c. The system will send an engine off response to the remote control. “remote” The remote control Notification will be two beeps descending in tone followed by the engine off animation. valet takeover operation To activate Valet takeover a. Park the vehicle and set the parking brake b.
“remote” The remote control Notification will be two beeps ascending in tone followed by the remote start animation. turbo mode remote start To activate Turbo mode a. Park the vehicle and set the parking brake b. Leave the engine running and remove your foot from the brake pedal. c. Press and release the ������� and buttons together. d. The lights will flash or turn on to confirm the remote start has taken control of the engine. e. Remove the key. The engine will continue to run. f.
there may be a delay for the glow plugs to warm. e. The engine can be turned off via remote control at this time without exiting timer mode. If not turned off, the engine will run for the programmed run time and will restart every three hours for 18 hours. note: if programmed to temperature timer mode, the remote start will check the temperature every three hours, and will only start if the temperature is below 0 degrees F.
It can be turned on or off anytime with the remote control as weather necessitates. note: This optional feature must be programmed on and connected to the vehicle rear defogger circuit to operate. Check with your installer for vehicle compatibility if you desire to have this feature included. rear defogger operation Press until the vehicle lights flash, the remote control ������� and and buttons simultaneously to turn the rear defogger output on and off. ������� “system” a.
remote start safety features This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components. ➜ starter anti-grind circuitry Whenever the vehicle is remote started, advanced anti-grind circuitry prevents the starter from engaging, even if the key is turned to the start position. This prevents damage to the starter motor if the key is turned to the start position during remote start operation.
➜ over and under rev protection The system monitors the engine speed and will automatically shut the engine off if the RPMs rise above or fall below the programmed levels. This feature prevents damage to the motor due to fuel delivery system failures or other problems which may cause the engine to race. note: The system uses a wire connected to the vehicle to sense engine speed. This wire must be connected in order for over and under rev protection to work.
diagnostics The microprocessor at the heart of your system is constantly moni toring all of the switches and sensors connected to it. It is designed to detect any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will record and report any triggers that occurred during your absence. ➜ arming diagnostics Each time this system is armed it runs a diagnostic routine to test for active alarm inputs.
note: sensor inputs that are triggered too many times will be bypassed using a feature called NPC for Nuisance Prevention. ➜ nuisance prevention circuitry This diagnostic feature monitors the sensor inputs for excessive trig‑ gers and bypasses them automatically to avoid annoying repeated trig‑ gers. how it works If any sensor input is triggered 3 times within a one hour period, it will be bypassed for one hour. The input will still be moni‑ tored, but the alarm will not sound if a trigger is detected..
Action Arm Number of Chirps Description 1 System armed Arm 1 (3-second delay), 1 System armed with zone bypass System disarmed Disarm 2 Disarm 4 System disarmed with trigger alert Disarm 5 System active disarmed NPC ➜ zone identification This system has several inputs (or zones) that can trigger the alarm while armed. Each zone input is identified by an icon on the remote control and by groups of flashes by the status led.
alarm remote con‑ led Sensor or optional Zone trol icon connection flashes vehicle circuit 1 1 Trunk switch 2 2 Shock sensor 3 3 Door switch 4 4 Optional 5 5 Ignition switch 6 6 Hood switch sensor code hopping The receiver and remote controls use a mathematical formula called an algorithm to change their code each time the remote control is used. This technology has been developed to increase the security of the unit.
or the battery has been removed, it may fall out of sync with the control unit and fail to operate the system. To re-sync the remote simply press several times within range of the vehicle. The alarm will automatically re-sync and respond to the remote controls normally. ������� owner recognition Owner Recognition is a revolutionary feature available only from Directed. Using a Directed Bitwriter®, hand-held programming tool, your dealer can program many of the system settings.
and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery.
remote control programming The remote control can be programmed for your particular preferences. Programming is performed using the programming and function buttons as described below. Function button operations during programming: Press the or button to scroll and highlight menu and feature items.
when it will not be used for long periods of time. It will not respond to any RF signals or function button presses when asleep. 1. Enter programming mode 2. Scroll to highlight the OFF icon 3. Press the button to choose and access the POWER screen, CONFIRM is highlighted. 4. button to enter sleep mode or highlight exit Press the and press the 5. Press the ������� button to return to the main menu. button anytime to exit programming.
➜ page mode on/off When Page is off, the remote control will not receive Pages or output Page Notifications or Alerts. It will only receive Command Reponses. 1. Enter programming mode 2. Scroll to highlight OPERATION 3. Press to choose the operation menu screen 4. Scroll to highlight PAGE and press 5. Scroll to highlight the desired setting. 6. Press to choose. to save and return to the Operation menu or ������� to save the setting and exit.
system programming options This system includes programming options that can enhance or defeat some of the features discussed in this manual. It also includes features not discussed that can expand the system’s convenience and security capabilities. Some optional features may require additional parts and labor to operate as designed. Cost should be discussed with your installer before implementing any optional features.
The alarm can be programmed to automatically arm after exiting the vehicle. Refer to Passive Arming section of this guide for more details. Passive locking The door can be programmed to lock when the alarm passively arms. Forced passive arming The alarm can be programmed to arm after one hour even if an entry point is accidentally left open.
Comfort Closure The door lock output timing can be extended for vehicles with an all close feature at the driver door key cylinder. Ignition controlled dome light This feature will turn the dome light on when the ignition is turned off. The default setting is on, and can be programmed off if the feature is not desired.
security & convenience expansion Listed below are some of the many expansion options available. Please consult your dealer for a complete explanation of all the options avail able to you. Audio Sensor: Metal on glass, glass cracking, and breaking glass each produce distinctive acoustic signatures. The 506T audio sensor uses a microphone to pick up sounds, and then analyzes them with proprietary acoustic software to determine if the glass has been struck.
will automatically turn on your parking and headlights when it gets dark. In addition, the 545T will turn your headlights on whenever the windshield wipers are used. A transmitter function can also be used to turn on your parking and headlights for a programmed time. Power Trunk Release: The channel two output of the system can operate a factory power release for the vehicle’s trunk or hatch. (An additional relay may be required.
✂ quick reference guide Arming Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. To arm, press . When the system arms, you will hear a short chirp, and the parking lights will flash once. Arming while driving To arm the system while driving, press on your remote control while the vehicle is running. The system will chirp once and then once more to indicate that the ignition is on. ������� Disarming To disarm, press .
54 © 2006 directed electronics—all rights res er ved
© 2006 directed electronics—all rights reser ved 55
The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.