Operator's Manual Original Operating Instructions 26750TSC Compact Tiller GAS/OIL RATIO 50:1 Product #: 26750TSC Email for more information info@ardisam.com P/N: 13461 ECN: 9580 Rev. 10/11/12 © 2012 Ardisam, Inc.
Operator's Manual 26750TSC Compact Tiller INTRODUCTION Congratulations on your investment in quality. Thank you for purchasing the 26750TSC Compact Tiller from HUSKEE®. We have worked to ensure that this tiller meets the highest standards for usability and durability. With proper care, your tiller will provide many years of service. Please read this entire manual before installation and use.
Operator's Manual 26750TSC Compact Tiller Warnings and Safety Precautions Operator's RESPONSIBILITY Accurate assembly and safe and effective use of the machine is the operator's responsibility. • Read and follow all safety instructions. • Carefully follow all assembly instructions. • Maintain the machine according to directions and schedule included in this HUSKEE operator’s manual. • Ensure that anyone who uses the machine is familiar with all controls and safety precautions.
Operator's Manual 26750TSC Compact Tiller General Safety Rules • Read, understand, and follow all instructions on the machine and in the manual(s). Be thoroughly familiar with the controls and the proper use of the machine before starting. • Use this equipment for its intended purpose only. • Familiarize yourself with all of the safety and operating decals on this equipment and on any of its attachments or accessories. • Do not put hands or feet near or under rotating parts.
Operator's Manual 26750TSC Compact Tiller • Tines rotate when the tiller is engaged; tines rotate when the drive safety control lever is pulled down. Releasing the drive safety control lever to the neutral position stops the tines. • Do not overload the machine capacity by attempting to till too deep at too fast of a rate. • Be careful when tilling in hard ground. The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine.
Operator's Manual 26750TSC Compact Tiller • Always wipe up excess (spilled) fuel from engine before starting. Clean up spilled fuel immediately. If fuel is spilled, do not start the engine but move product and fuel container from area. Clean up spilled fuel and allow to evaporate and dry after wiping and before starting. Children and bystanders Tragic accidents can occur if the operator is not alert to the presence of children and/or bystanders.
Operator's Manual 26750TSC Compact Tiller SAFETY DECALS This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
Operator's Manual 26750TSC Compact Tiller Unpacking and Assembly Unpacking and Assembling Your Tiller 1. Open top of carton and remove handlebar assembly. 2. Parts bag for compact tiller contains: 2- Bolts M8 x 1.25 x 20 Hex Head 6- Bolts M8 x 1.25 x 25 Hex Head 6- Washers M8 8.4mm x 24mm x 2.2mm 6- Nuts M8 x 1.25 important The right and left sides of your rototiller are determined from the operating position as you face the direction of forward travel. Engine is shipped from factory without oil.
Operator's Manual 26750TSC Compact Tiller 5. Assemble tine shield extensions using six (6) M6 bolts and six (6) nylock nuts. SEE FIGURE 4 6. Assemble tines to unit. Sharp edges of tines will be away from the operator at the top or facedown at front of machine. Fasten outer tines to the inner tines using the 8mm x 40mm lock pins already affixed to the inner tines.
Operator's Manual 26750TSC Compact Tiller Features drive safety control lever adjustable forward cable adjustable handlebar height adjustable depth regulator transport wheels tines Specifications ENGINE DISPLACEMENT 99cc tilling width 11 in., 16 in., 21 in. tilling DEPTH 11 in. tine speed 178 rpm WHEEL SIZE 8” diameter WEIGHT OF UNIT 90 lb UNIT SIZE L x W x H (inches) 51” x 24” x 41” 10 For additional information email info@ardisam.
Operator's Manual 26750TSC Compact Tiller Operation Controls Drive SAFETY Control Lever Engage tines into forward, releasing returns machine to neutral. Pulling down on drive safety control lever engages the tines. Releasing the drive safety control lever to a neutral position disengages the tines. BELT TENSION ADJUSTMENT Caution This information is provided here only to introduce the controls. DO NOT START THE ENGINE AT THIS TIME. Starting and operating instructions are given on page 11.
Operator's Manual 26750TSC Compact Tiller PRE-START Inspection 1. Make sure all safety guards are in place and all nuts and bolts are secure. 2. Check oil level in engine crankcase. See your engine manual for procedure and specifications. 3. Inspect air cleaner for cleanliness. See your engine manual for procedure. 4. Check the fuel supply. Fill the fuel tank no closer than 1 inch from top of tank to provide space for expansion. See your engine manual for fuel recommendations. 5.
Operator's Manual 26750TSC Compact Tiller Operating Speed For normal tilling, set the throttle lever to FAST. SHUTTING DOWN To stop the engine at any time, turn the On/Off switch to the OFF position. To stop tines at any time, release the drive safety control lever to the neutral position. Tilling 1. Adjust the depth regulator lever to desired tilling depth. NOTE: Raise depth regulator lever up one hole at a time, testing tiller operation after each raise.
Operator's Manual 26750TSC Compact Tiller SERVICING THE ROTOTILLER The following information will help you make the necessary checks and perform the procedures required to follow the normal care recommendations made for your rototiller unit. If you prefer, your local authorized dealer can make these checks and perform the required procedures for you. Warning C heck forwa rd be lt tension regu l a r ly. Too much or too little tension will cause premature belt failure.
Operator's Manual 26750TSC Compact Tiller Engine Maintenance Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides detailed information and a maintenance schedule for performing the following tasks: 1. Check oil level before each use or after every 8 hours of operation. 2. Change oil after first 5-8 hours of operation. Change oil while engine is warm. Refill with new oil of recommended grade. 4.
Operator's Manual 26750TSC Compact Tiller Troubleshooting and Repair Warning Troubleshooting Guide Practice safety at all times. Engine must be turned off and allowed to cool, and spark plug wire must be disconnected and secured before attempting any maintenance or repair. Failure to comply with this safety requirement can result in serious personal injury to you or bystanders.
Operator's Manual 26750TSC Compact Tiller Parts Breakdown Handlebar assembly Parts explosion and Parts List 7 8 9 6 21 5 18 10 12 11 13 19 17 16 15 14 22 1 2 3 4 20 REF. NO. PART # 3 2 1 DESCRIPTION QTY. 1 18135 BOLT M8 X 1.25 X 25 SFH GR8.8 ZN 6 2 3245 WASHER M8 8.4MM X 24MM X 2.2MM ZN 6 3 64132 NUT M8 X 1.
Operator's Manual 26750TSC Compact Tiller 2 29 23 11 22 21 7 30 10 9 26 27 6 5 10 15 4 8 10 26 27 25 1 28 11 3 13 14 12 16 18 19 20 17 24 Engine assembly Parts explosion 18 For additional information email info@ardisam.
Operator's Manual 26750TSC Compact Tiller Engine assembly Parts List REF. NO. PART # DESCRIPTION QTY. 1 53617 ARM FORWARD REAR TINE 1 2 13364 Forward Idler Pulley 10mm 1 3 332033 Bolt M10 x 1.5 x 50 hhcs 1 4 W1265V0915 Bolt M8 x 25 hhcs 2 5 W1265V0904 Bolt M8 x 1.25 x 20 HHCS 2 6 18008 BUSHING 16.4MM X 22MM X 21.5MM 1 7 38397 KEY 3/16IN X 1.75IN 1 8 3235 Nut M10 x 1.5 htplk 1 9 803 WASHER 5/16"ID X 1-1/2"OD FLAT 16 GA.
Operator's Manual 26750TSC Compact Tiller 23 17 3 15 12 19 11 20 8 20 21 16 11 8 8 13 11 1 4 6 7 10 7 13 2 9 14 5 22 8 18 21 Chassis assembly Parts explosion For additional information email info@ardisam.
Operator's Manual 26750TSC Compact Tiller Chassis assembly Parts List REF. NO. PART # DESCRIPTION QTY. 1 18004 WELDMENT FRAME 1 2 13366 Lock pin wire bale 1 3 92776 BOLT M6 X 1.0 X 20 HHCS GR8.8 ZN 2 4 18010 HANDLEBAR LOWER STRAP 1 5 W1265V0904 BOLT M8 X 1.25 X 20 HHCS ZN GR8.8 2 6 3245 WASHER M8 8.4MM X 24MM X 2.2MM ZN 2 7 3252 NUT M8 X 1.25 H GR8.8 ZN 4 8 W1265V0913 NUT M6 X 1.0 HNYLK GR8.8 ZN 10 9 3247 BOLT M8 X 1.25 X 45 HHFCS GR8.
Operator's Manual 26750TSC Compact Tiller Transmission assembly Parts Explosion and Parts LIst 20 22 24 28 13 11 10 18 3 19 2 15 17 1 5 26 9 8 27 27 7 12 26 24 6 14 16 21 4 15 14 6 25 23 22 23 25 REF. NO. PART # DESCRIPTION QTY. 1 13610 Worm Driveshaft 20mm od REF. NO. PART # DESCRIPTION QTY. 1 16 13615 Gear Brass 25mm id 6mm Key ft 1 17 13590 Bushing 26mm x 20.22mm x 6.
Operator's Manual 26750TSC Compact Tiller Front Tine RotoTillers Warranty Terms and Conditions Product Warranty: 1-Year Limited Warranty Ardisam, Inc., a manufacturing company, warrants this HUSKEE® 26750tsc Compact TILLER to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one-year warranty of this product, Ardisam will furnish, at their discretion, parts and labor to correct any defect caused by faulty material or workmanship.
1160 8th Avenue, PO Box 666 Cumberland, WI 54829 800-345-6007 | Fax 715-822-2223 E-mail: info@ardisam.com All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Items used for props not included. Some assembly may be required. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 Distributed by: Tractor Supply Co.® 200 Powell Place Brentwood, TN 37027 www.
