OWNER’S MANUAL Chrysler Group LLC 13ZD-126-AA First Edition 1135554cv1 Viper Printed in U.S.A. 13ZD-126-AA Chrysler 1" gutter 07/11/2012 15:40:46 2013 Viper 2013 OWNER’S MANUAL Chrysler Group LLC 13ZD-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine MOPAR威 parts, and cares about LLC vehicle. Be assured that it represents precision your satisfaction. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .11 䡵 REMOTE KEYLESS ENTRY (RKE) . . . . . . . . . . .17 ▫ Keyless Ignition Node (KIN) . . . . . . . . . . . . . .11 ▫ To Unlock The Doors. . . . . . . . . . . . . . . . . . . .17 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .18 ▫ Ignition Or Accessory On Message . . . . . . . . . .12 ▫ To Unlatch The Liftgate . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .24 ▫ Seat Belts and Pregnant Women . . . . . . . . . . . .38 ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .24 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .38 ▫ Auto-Down Feature . . . . . . . . . . . . . . . . . . . .25 ▫ Driver And Passenger Supplemental Restraint System (SRS) - Airbags . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 NOTE: In case the ignition does not change with the push of a button, the RKE transmitter (Key Fob) may Your vehicle uses a keyless ignition system. This system have a low or dead battery. consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Keyless Ignition Node (KIN).
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle hatch should the battery in the vehicle or the Key Fob go dead. To remove the emergency key, slide the mechanical latch on the back of the Key Fob sideways with your thumb and then pull the key out with your other hand.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster. NOTE: With the Uconnect Touch™ system, the power window switches, radio and power outlets will remain active for up to 10 minutes after the ignition is cycled to the OFF position. Opening either front door will cancel this feature. The time for this feature is programmable.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from vehicle, cycle the ignition OFF and lock all doors when leaving the vehicle unattended. VEHICLE SECURITY ALARM SYSTEM Rearming of the System If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals (flashing lights) after 15 minutes, and then rearm itself.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Entering The Liftgate With The System Armed • Press the Keyless Enter-N-Go™ Start/Stop button (requires at least one valid Key Fob in the vehicle). NOTE: Using the key to open the liftgate while the Vehicle Security Alarm is armed will trigger the alarm. NOTE: Press the LIFTGATE release button on the RKE transmit- • The liftgate key cylinder cannot arm or disarm the ter twice to allow access without triggering the alarm or Vehicle Security Alarm.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Alarm is armed and the battery becomes disconnected, the Vehicle Security Alarm will remain armed when the battery is reconnected; the exterior lights will flash, the horn will sound. If this occurs, disarm the Vehicle Security Alarm. ILLUMINATED ENTRY The interior lights will turn on whenever a door is opened or the liftgate is opened and the dimmer switch is not in the defeat position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually. 2 REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors and liftgate, or activate the Panic Alarm from distances up to approximately 200 ft (60 m) using a hand-held Key Fob with RKE transmitter.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Uconnect™ Access Programmable Settings” in “Under- To Lock The Doors standing Your Instrument Panel” for further information. Press and release the LOCK button on the RKE transmitRemote Key Unlock, Driver Door/Both Doors First ter to lock the doors. The horn will chirp once and the park lights and turn signal lights will flash to acknowlThis feature lets you program the system to unlock either edge the signal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Using The Panic Alarm Programming Additional Transmitters To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights will turn on, the park lights will flash, the horn will pulse on and off, and the interior lights will turn on. Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 If your RKE transmitter fails to operate from a normal 3. The RKE transmitter battery may be weak or dead. distance, check for these two conditions: The expected life of the battery is a minimum of three years. 1. Closeness to a radio transmitter, such as a radio station tower, airport transmitter, and some mobile or CB DOOR LOCKS radios can affect transmitter operation.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be injured seriously or fatally. Don’t leave the ignition in the ON position. A child could operate power windows, other controls, or move the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 is open, and the ignition is in the ACC or ON/RUN position, a chime will sound as a reminder to remove the Key Fob. Automatic Door Locks The auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 5 mph (8 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer for service.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit Programming To change the current setting, refer to “Uconnect威 Settings” in “Understanding Your Instrument Panel” for further information. NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws. WINDOWS Power Windows The window controls on the driver’s door control both of the door windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Opening either front door will cancel this feature. The time is programmable. Refer to “Uconnect™ Access Settings” in “Understanding Your Instrument Panel” for further information. WARNING! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, and do not leave a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To close the window part way, lift the window switch to Reset Auto-Up the first detent and release it when you want the window Should the Auto Up feature stop working, the window to stop. probably needs to be reset. To reset Auto Up: NOTE: 1. Pull the window switch up to close the window completely and continue to hold the switch up for an • If the window runs into any obstacle during autoadditional two seconds after the window is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Once unlocked, the liftgate can be opened or closed. To open the liftgate, press the LIFTGATE RELEASE switch located under the right side of the tail panel, which is located below the liftgate, then pull the liftgate open with one fluid motion. Rear Panel Manual Lock Cylinder To unlock the liftgate with the RKE transmitter, press the LIFTGATE button on the RKE transmitter two times.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The liftgate release switch will be ignored under the following conditions: • When the ignition is in ON/RUN and the parking brake is not set. • When vehicle speed is not 0 mph (0 km/h). • When all doors are locked (except for RKE transmitter liftgate access). Refer to “Entering the Liftgate with the System Armed — Coupe” under “Security Alarm System” for additional information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped If you will be carrying children too small for adult-sized • Three-point lap and shoulder belts for all seating seat belts, the seat belts or the Lower Anchors and Tether positions for CHildren (LATCH) feature also can be used to
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is located at the side of your 4. When the belt is long enough to fit, insert the latch seat back. Grasp the latch plate and pull out the belt. plate into the buckle until you hear a “click.” Latch Plate 3. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! WARNING! (Continued) • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the lap belt across your thighs, below your 6. To loosen the lap belt if it is too tight, lift up on the abdomen. To remove slack in the lap belt portion, pull shoulder belt and pull on the lap belt. A snug belt up a little on the shoulder belt, as shown. reduces the risk of sliding under the belt in an collision. WARNING! Removing Slack From Belt • A lap belt worn too high can increase the risk of injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 7. Position the shoulder belt on your chest so that it is Lap/Shoulder Belt Untwisting Procedure comfortable and not resting on your neck. The retrac- Use the following procedure to untwist a twisted lap/ tor will withdraw any slack in the belt. shoulder belt. 8. To release the belt, push the red button in the buckle. 1. Position the latch plate as close as possible to the The belt will retract automatically to its stowed posianchor point. tion.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert姞) BeltAlert威 is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert威) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both front seat belts are fastened.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Automatic Locking Retractor Mode (ALR) — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combination lap/shoulder belt. Use the Automatic Locking Mode anytime a child safety seat is installed in a seating position that has a belt with this feature.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners — If Equipped Seat Belts and Pregnant Women The seat belts for both front seating positions may be equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of an collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in an collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • No objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 The airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on several factors, including collision severity and occupant size. even a small adult. Therefore, even if the driver’s Advanced Front Airbag deploys, the passenger’s Advanced Front Airbag may not deploy.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE shut OFF. An airbag deployment can cause severe injury or death to an infant in this position. Refer to “Passenger Airbag Disabled (PAD) Indicator Light”. child safety seat or booster seat. If too large for a booster seat, the child should wear the lap/shoulder belt properly. 3. A child who is not big enough to wear the vehicle seat 8.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Knee Impact Bolsters • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors The Knee Impact Bolsters help protect the knees of the driver and the passenger, and position front occupants • Occupant Classification System (OCS) for the best interaction with the airbags.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not add a secondary seat cover other than those may modify the rate of passenger airbag inflation or prevent passenger airbag deployment based on input approved by Chrysler Group LLC/Mopar威. from the Occupant Classification System (OCS). The ORC • At no time should any supplemental restraint system will not detect roll-over or rear impacts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Because airbag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an airbag should have deployed. Seat belts are necessary for your protection in all collisions, and also are needed to help keep you in position, away from an inflating airbag.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 If there is a fault present in the OCS, the Airbag Warning Light will turn on. This indicates that you should take the vehicle to an authorized dealer for service. The Airbag Warning Light will turn on whenever there is a fault present, which can affect the operation of the airbag system. If there is a fault present in the OCS, both the PAD Indicator Light and the Airbag Warning Light will illuminate to show that the passenger airbag is turned off.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The passenger airbag will not be enabled for most any size child who is seated properly in the passenger seat and for most properly installed child restraint systems. However, under certain conditions, even with a properly installed child restraint system, the PAD Indicator Light may not be on, even though the airbag is disabled. This can occur if the child restraint is lighter than the threshold weight necessary to turn the PAD Indicator Light on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 proper airbag deployment. Do not make any modifica- • Turn on the interior lights, which remain on as long as the battery has power or until the ignition is cycled to tions to the passenger seat components, assembly, or to OFF. the seat cover. If the seat, trim cover, or cushion needs service for any reason, take the vehicle to your autho• Unlock the doors automatically. rized dealer.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the airbags, any or all of the following may occur: continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front Do not drive your vehicle after the airbags have depassenger as the airbags deploy and unfold. The ployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Rearward-facing infant restraints must never be secured in the passenger seat of a vehicle with a passenger airbag. In a collision, a passenger airbag may deploy causing severe injury or death to infants riding in rearward-facing infant restraints. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! (Continued) • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchorages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal injury.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For additional information, refer to Child Restraint Tether Anchor www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents, should refer to Transport Canada’s webChild restraints having tether straps and hooks site for additional information. http://www.tc.gc.ca/ for connection to tether anchors have been roadsafety/safedrivers/childsafety/index.htm available for some time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 2 Child Tether Access Cover Child Tether NOTE: While the child tether is in use, keep the access cover in a safe place so that it can be replaced after use of the child tether. 4. Pass the child restraint tether hook through either opening in the seatback underneath the head restraint.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Attach the tether hook to the anchor loop. 8. Install the child restraint according to the manufacturer’s directions. 9. Remove slack from the tether strap according to the child restraint manufacturer’s directions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 To restrain the child seat: retractor. In this mode, you will only be able to retract excess webbing into the retractor to secure the child restraint. 1. Pull enough webbing from the retractor to allow the belt to pass through the child restraint and insert the Transporting Pets latch plate into the buckle until you hear a “click.” Deploying airbags could harm your pet. An unrestrained 2.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Avoid driving at a constant speed, either fast or slow, SAFETY TIPS for long periods. Transporting Passengers • Do not make any full throttle starts and avoid full NEVER TRANSPORT PASSENGERS IN THE CARGO throttle acceleration. AREA. • Use the proper gear for your speed range. • Wait until the engine has reached normal operating temperature before driving at the recommended maximum break-in speed. • Avoid excessive idling.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Inspect the belt system periodically, checking for cuts, Defroster frays, and loose parts. Damaged parts must be replaced Check operation by selecting the defrost mode and place immediately. Do not disassemble or modify the system. the blower control on high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Periodic Safety Checks You Should Make Outside The Vehicle Lights Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument Examine tires for excessive tread wear and uneven wear panel. patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for Door Latches cuts and cracks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 ▫ Automatic Dimming Mirror . . . . . . . . . . . . . .68 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .69 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . .70 䡵 Uconnect™ Phone — IF EQUIPPED . . . . . . . . . .71 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . . .113 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .119 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .122 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . .115 ▫ Intermittent Wiper System . . . . . . . . . . . . . . .122 ▫ Automatic Headlights . . . . . . . . . . . . . . . . . .116 ▫ Wiper Operation . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .129 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . . .139 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .129 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . .139 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . .129 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . .140 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror NOTE: The mirror contains an Assist button and a 9–1–1 button located on the bottom of the mirror. This mirror automatically adjusts for headlight glare from Assist Call vehicles behind you. This feature will be defaulted on, and The rear view mirror contains an ASSIST push button only be disabled when the vehicle is moving in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the Report an accident without taking your eyes off the road. lane next to your vehicle. Just press 9-1-1 on your mirror and connect. 9-1-1 Call CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power mirror controls consist of mirror select butThe power mirror controls are located on the driver-side tons and a four-way mirror control switch. To adjust a mirror, press either the L (left) or R (right) to select the door trim panel. mirror that you want to adjust. Power Mirrors NOTE: A light in the selected button will illuminate indicating the mirror is activated and can be adjusted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 mobile phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect™ Phone. NOTE: The Uconnect™ Phone requires a mobile phone equipped with the Bluetooth威 “Hands-Free Profile”, Version 0.96 or higher. See the Uconnect™ website for supported phones. For Uconnect™ customer support, visit www.UconnectPhone.com or call 1–877–855–8400.
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE standard that enables different electronic devices to connect to each other without wires or a docking station, so Uconnect™ Phone works no matter where you stow your mobile phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect™ Phone. The Uconnect™ Phone allows up to seven mobile phones to be linked to the system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 The Uconnect™ Phone is fully integrated with the vehi- • Prior to giving a voice command, one must wait for the beep, which follows the “Ready” prompt or another cle’s audio system. The volume of the Uconnect™ Phone prompt. can be adjusted either from the radio volume control knob or from the steering wheel radio control (right • For certain operations, compound commands can be switch), if so equipped. used.
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Tree Pair (Link) Uconnect™ Phone To A Mobile Phone Refer to “Voice Tree” in this section. To begin using your Uconnect™ Phone, you must pair your compatible Bluetooth威 enabled mobile phone. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say “Help” following the beep. The Uconnect™ Phone will play some of the options at any prompt if you ask for help.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 enter into your mobile phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process. Uconnect™ Phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “Advanced Phone Connectivity” in this section).
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call By Saying A Name • Press the button to begin. Phonebook Download – Automatic Phonebook Transfer From Mobile Phone If equipped and specifically supported by your phone, • After the “Ready” prompt and the following beep, say Uconnect™ Phone automatically downloads names (text “Call”. names) and number entries from your mobile phone’s • The system will prompt you to say the name of the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 • A maximum of 1000 entries per phone will be down- Add Names To Your Uconnect™ Phonebook loaded and updated every time a phone is connected NOTE: Adding names to the Uconnect™ Phonebook is to the Uconnect™ Phone. recommended when the vehicle is not in motion. • Depending on the maximum number of entries downbutton to begin. • Press the loaded, there may be a short delay before the latest downloaded names can be used.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button to begin. After you are finished adding an entry into the phone- • Press the book, you will be given the opportunity to add more • After the “Ready” prompt and the following beep, say phone numbers to the current entry or to return to the “Phonebook Edit Entry”. main menu. • You will then be asked for the name of the phonebook The Uconnect™ Phone will allow you to enter up to 32 entry that you wish to edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 mobile and a home number, but you can add “John Doe’s” work number later using the “Phonebook Edit Entry” feature. from the list, press the button while the Uconnect™ Phone is playing the desired entry and say “Delete”. • After you enter the name, the Uconnect™ Phone will ask you which designation you wish to delete: home, NOTE: Editing phonebook entries is recommended work, mobile, other, or all. Say the designation you when the vehicle is not in motion.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE but• The Uconnect™ Phone will ask you to verify that you • To call one of the names in the list, press the ton during the playing of the desired name, and say wish to delete all the entries from the phonebook. “Call”. • After confirmation, the phonebook entries will be NOTE: The user can also exercise “Edit” or “Delete” deleted. operations at this point.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 NOTE: The Uconnect™ Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can When you receive a call on your mobile phone, the only answer an incoming call or ignore it. Uconnect™ Phone will interrupt the vehicle audio system, if on, and will ask if you would like to answer the Making A Second Call While Current Call Is In button to accept the call.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE press and hold the button until you hear a double beep, indicating that the two calls have been joined into If two calls are in progress (one active and one on hold), one conference call. button until you hear a single beep, indicatpress the ing that the active and hold status of the two calls have Call Termination switched. Only one call can be placed on hold at a time. To end a call in progress, momentarily press the butConference Call ton.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 • The Uconnect™ Phone will call the last number that • After the ignition is cycled to OFF, a call can continue on the Uconnect™ Phone for a certain duration, after was dialed from your mobile phone. which the call is automatically transferred from the NOTE: This may not be the last number dialed from the Uconnect™ Phone to the mobile phone. Uconnect™ Phone. • An active call is automatically transferred to the mobile phone after the ignition is cycled to OFF.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After selecting one of the languages, all prompts and • After the “Ready” prompt and the following beep, say “Emergency” and the Uconnect™ Phone will instruct voice commands will be in that language. the paired mobile phone to call the emergency number. NOTE: After every Uconnect™ Phone language change This feature is supported in the U.S., Canada, and operation, only the language-specific 32-name phoneMexico. book is usable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 WARNING! To use your Uconnect™ Phone System in an emergency, your mobile phone must be: • turned on, • paired to the Uconnect™ System, • and have network coverage. Roadside Assistance If you need roadside assistance: NOTE: • The roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico).
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE followed by the word “Send”. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you To learn how to access your voice mail, refer to “Working can press the button and say, “3 7 4 6 # Send”. with Automated Systems”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 NOTE: Turning Confirmation Prompts ON/OFF • You may not hear all of the tones due to mobile phone Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ network configurations. This is normal. Phone will not repeat a phone number before you dial it). • Some paging and voice mail systems have system time button to begin. out settings that are too short and may not allow the • Press the use of this feature.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE using Uconnect™ Phone. The status is given for network Mute/Un-Mute (Mute ON/OFF) signal strength, phone battery strength, etc. When you mute the Uconnect™ Phone, you will still be able to hear the conversation coming from the other Dialing Using The Mobile Phone Keypad party, but the other party will not be able to hear you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 from your Uconnect™ Phone paired mobile phone to the • When prompted, say “List Phones”. button Uconnect™ Phone or vice versa, press the • The Uconnect™ Phone will play the phone names of and say “Transfer Call”. all paired mobile phones in order from the highest to the lowest priority. To “Select” or “Delete” a paired Connect Or Disconnect Link Between The phone being announced, press the button and say Uconnect™ Phone And Mobile Phone “Select” or “Delete”.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button at any time while the • You can also press the button at any time while the • You can also press the list is being played, and then choose the phone that list is being played, and then choose the phone you you wish to select. wish to delete. • The selected phone will be used for the next phone call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • Press and hold the the session begins, or, button for five seconds until • After the “Ready” prompt, and the following beep, say “Setup”, then “Reset”. button and say the “Voice Training”, This will delete all phone pairing, phone book entries, • Press the “System Training”, or “Start Voice Training” com- and other settings in all language modes. The System will prompt you before resetting to factory settings. mand.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • It is not recommended to store similar sounding names in the Uconnect™ Phonebook. • Phonebook (Downloaded and Uconnect™ Phone Local) name recognition rate is optimized when the entries are not similar. • Numbers must be spoken in single digits.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Far End Audio Performance Recent Calls • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. If your phone supports “Automatic Phonebook Download”, Uconnect™ Phone can list your Outgoing, Incoming and Missed Calls. SMS Uconnect™ Phone can read or send new messages on your phone.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Uconnect™ Phone will play the new text message for Uconnect™ Phone will prompt you to say the name or number of the person you wish to send the message to. you. After reading a message, you can “Reply” or “Forward” List of Preset Messages: the message using Uconnect™ Phone. 1. Yes Send Messages: 2. No You can send messages using Uconnect™ Phone. To send 3. Where are you? a new message: 4. I need more direction. button. • Press the 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 11. See You in 15 minutes • Press the 12. I am on my way • After the “Ready” prompt and the following beep, say “Setup, SMS Incoming Message Announcement,” you will then be given a choice to change it. 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? button. Bluetooth威 Communication Link 18. When can we meet? Mobile phones have been found to lose connection to the Uconnect™ Phone.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 3
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais 3
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book Voice Commands Primary Alternate (s) previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect™ Tutorial voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. All attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Pressing the Voice Command button while the system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 To hear the first available Menu, press the Voice Com- Main Menu button and say “Help” or “Main Menu”. mand Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the Commands main menu. The Voice Command system understands two types of commands. Universal commands are available at all In this mode, you can say the following commands: times.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio AM (Or Radio Long Wave Or Radio Medium Wave — If Equipped) • “Previous Station” (to select the previous station) To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: Bluetooth威 Streaming (BT) Mode • “Menu Radio” (to switch to the radio menu) To switch to the AM band, say “AM” or “Radio AM”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • “Previous Track” (to play the previous track) Memo Mode • “List” (to list a Artist, Playlist, Album, Track, etc.) To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: Satellite Radio • “New Memo” (to record a new memo) — During the recording, you may press the Voice Command button to stop recording.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE – “Delete” (to delete a memo) • “Language Spanish” • “Delete All” (to delete all memos) • “Tutorial” Setup • “Voice Training” To switch to system setup, you may say on of the NOTE: Keep in mind that you have to press the Voice following: button first and wait for the beep before Command speaking the “Barge In” commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 2. Repeat the words and phrases when prompted by SEATS Uconnect™ Voice. For best results, the Voice Training Seats are a part of the Occupant Restraint System of the session should be completed when the vehicle is vehicle. parked, engine running, all windows closed, and the blower fan switched off. This procedure may be reWARNING! peated with a new user. The system will adapt to the last trained voice only.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seats Forward and Rearward Adjustment The adjusting bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Seat Adjustment Bar Seat Height Adjustment The seat height adjustment lever is located on the outboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 recliner lever upward and hold it until the seat returns to its full upright position. 3 Height Adjustment Lever Recliner Adjustment The recliner lever is located on the outboard side of the seat. To recline the seat, lean forward slightly, pull the recliner lever upward, lean backward until the seat is in the desired position, and release the lever.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. 3 Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Push upward or push downward on the seat switch, the seat will move in the direction of the switch.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 TO OPEN AND CLOSE THE HOOD 1. Reach into the back side area of the drivers front fender to gain access to the hood release lever. 2. Pull the hood release lever rearward to release the hood latches.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Lift the hood upward to the full forward position. CAUTION! • Do not leave the hood open in areas where strong gust of wind are likely. Such a place might be by the side of the road where large trucks pass by. Strong gusts of wind may damage the hood. Always close the hood in such situations. • To prevent possible damage, do not slam the hood to close it. Simply lower the hood until it is open approximately 6 in (15 cm) and then drop it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. 3 LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Headlights On with Wipers feature can be turned on or off using the Uconnect Touch™ System, This system automatically turns the headlights on or off refer to “Uconnect Touch™ Settings” in “Understanding according to ambient light levels. To turn the system on, Your Instrument Panel” for further information. rotate the headlight switch counterclockwise to the A (AUTO) position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: If allowed by law in the country in which the vehicle was purchased the Daytime Running Lights can • The lights must be turned off within 45 seconds of be turned on and off using the Uconnect Touch™ System, placing the ignition in the OFF position to activate this refer to “Uconnect Touch™ Settings” in “Understanding feature. Your Instrument Panel” for further information.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever Turn Signals The multifunction lever controls the operation of the turn Move the multifunction lever up or down and the arrows signals, headlight beam selection and passing lights. The on each side of the instrument cluster flash to show multifunction lever is located on the left side of the proper operation of the front and rear turn signal lights. steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 High/Low Beam Switch light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever Dimmer Controls toward you to switch the headlights back to low beam. The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the parking lights or headlights on, rotating the left The right dimmer control adjusts the ambient light for dimmer control upward will increase the brightness of the interior door release handles. the instrument panel lights and turn on the courtesy lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Interior Light Control Interior Light Defeat (OFF) Rotate the left dimmer control completely upward to the Rotate the left dimmer control to the extreme bottom OFF second detent to turn on the interior lights. The interior position. The interior lights will remain off when the lights will remain on when the dimmer control is in this doors are open. position. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Intermittent Wiper System The multifunction lever operates the windshield wipers and washer when the ignition is placed in the ON/RUN or ACC position. The multifunction lever is located on the left side of the steering column. Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause between cycles desirable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the “Park” position before turning off the engine.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE released. It will then resume the intermittent interval previously selected. If the washer knob is pushed while in the off position, the wiper will turn on and cycle approximately three times after the wash knob is released. Headlights On With Wipers (Available with Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 position, push the release lever forward to lock the column firmly in place. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The adjustable pedal switch is located to the left side of • Further small adjustments may be necessary to find the steering column. the best possible seat/pedal position. CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Adjustable Foot Rest To adjust the pedal: This feature allows the driver to adjust the foot rest 1. Adjust the seat and steering column to a comfortable forward or backward and to rotate it upward or downposition. ward to allow for greater driving comfort. 2. Using a 13 mm socket wrench, loosen the nut on the pedal. 3. Slide the pedal either forward or backward and rotate it upward or downward as desired. 4.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Electronic Speed Control buttons are located on the NOTE: In order to ensure proper operation, the Elecright side of the steering wheel. tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set A Desired Speed vehicle will deactivate Electronic Speed Control without erasing the set speed memory.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while the Electronic Speed Control is set, push the SET (-) button. If the button is continually held in the SET (-) position, the set speed will continue to decrease until the button is released. Release the button when the desired speed is reached, and the new set speed will be established. Pressing the SET (-) button once will result in a 1 mph (1.6 km/h) decrease in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Turning ParkView姞 On Or Off — With Touch Screen Radio 1. Turn the Radio on. The HomeLink威 buttons, located on the sunvisor, designate the three different HomeLink威 channels. The HomeLink威 indicator is located above the center button. 2. Press the “More” soft-key. 3. Press the “Settings” soft-key. 4. Press the “Safety & Driving Assistance” soft-key. 5. Press the check box soft key next to “Parkview威 Backup Camera” to enable/disable.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink姞 NOTE: Be sure that your vehicle is parked outside of the garage • Erasing all channels should only be performed when before you begin programming. programming HomeLink威 for the first time. Do not erase channels when programming additional buttons.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view. 3. Simultaneously press and hold both the HomeLink威 button you want to program and the hand-held transmitter button. Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1. Cycle the ignition to the ON/RUN position. 4. Continue to hold both buttons and observe the indicator light.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Firmly press and release the “LEARN” or “TRAIN- Reprogramming A Single HomeLink威 Button ING” button. On some garage door openers/devices To reprogram a channel that has been previously trained, there may be a light that blinks when the garage door follow these steps: opener/device is in the LEARN/TRAIN mode. 1. Cycle the ignition to the ON/RUN position. NOTE: You have 30 seconds in which to initiate the next 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view. • To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels. Reprogramming A Single HomeLink威 Button 3.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your hand-held For programming transmitters in Canada/United States transmitter every two seconds until HomeLink威 has that require the transmitter signals to “time-out” after successfully accepted the frequency signal. The indiseveral seconds of transmission.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 If you unplugged the garage door opener/device for Using HomeLink姞 programming, plug it back in at this time. To operate, press and release the programmed HomeLink威 button. Activation will now occur for the Reprogramming A Single HomeLink威 Button programmed device (i.e., garage door opener, gate operaTo reprogram a channel that has been previously trained, tor, security system, entry door lock, home/office lightfollow these steps: ing, etc.,).
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original hand-held transmitter. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code. • Did you unplug the device for programming and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • The term IC before the certification/registration number only signifies that Industry Canada technical speciThis device complies with FCC rules Part 15 and Industry fications were met. Canada RSS-210. Operation is subject to the following two conditions: ELECTRICAL POWER OUTLETS General Information 1. This device may not cause harmful interference. Your vehicle is equipped with two 12 Volt (13 Amp) 2.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One power outlet is located on the center console to the The second power outlet is located between the seat right of the shifter. Push down on the power outlet to backs above the cup holders. This power outlet is conaccess the opening. Push down on it again to close. This nected directly by the battery and powered at all times. power outlet is powered when the ignition is in the ON or ACC position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS — If Equipped STORAGE There are two cupholders located in the rear of the center Glovebox Storage console. An electronic glovebox storage compartment is located on the passenger side of the instrument panel. Push in the button to open the glovebox.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Console Features Console Cubby Bin — If Equipped An open storage area, or cubby bin, is located in the center console rearward of the shift lever. 3 Opened Glove Box Storage Compartment NOTE: The glovebox storage compartment will lock with the door locks.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Net Storage— If Equipped Storage Bin — If Equipped There is a cargo net storage area located between the There is a storage bin located between the driver and driver and passengers seat. passengers seat. Pull up on the release lever to open the storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Door Storage The door panels contain storage areas located in the lower center area of the door panel.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .151 ▫ EVIC Green Telltales . . . . . . . . . . . . . . . . . . .172 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .152 ▫ EVIC Selectable Menu Items . . . . . . . . . . . . . .172 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .153 ▫ Screen Setup Driver Selectable Items . . . . . . . .177 䡵 ELECTRONIC VEHICLE INFORMATION CENTER 䡵 Uconnect™ ACCESS SETTINGS. . . . . . . . . . . (EVIC) . . . . . . . . . . . . . .
150 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 STEERING WHEEL AUDIO CONTROLS . . . . . .190 ▫ Winter Operation. . . . . . . . . . . . . . . . . . . . . .197 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .190 ▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . .197 䡵 RADIO ANTENNA . . . . . . . . . . . . . . . . . . . . .190 ▫ Window Fogging and Frosting . . . . . . . . . . . .197 䡵 RADIO OPERATION AND MOBILE PHONES . .191 ▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 151 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 — Air Outlet — Sound System Speaker — Instrument Cluster — Keyless Enter-N-Go™ Start/Stop Button — Glove Compartment Lock 6 — Passenger Air Bag 7 — Glove Compartment 8 — Uconnect Touch™ System 9 — Uconnect Touch™ System Hard Controls 10 — Switch Bank (Screen Off, Hazard Switch, Back Button) 11 — Climate Controls 12 — Dimmer Controls 13 — Headlight Switch
152 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 153 INSTRUMENT CLUSTER DESCRIPTIONS 1. Speedometer Indicates vehicle speed. 2. Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition is first cycled to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.
154 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Leaving the hazard flashers on for extended • Selectable Information (Compass, Temp, Range, to periods will wear down the battery. Empty, Trip A, Trip B, Average MPG) 5. High Beam Indicator • Menu Titles / Odometer This indicator shows that the high beam head- • Menu Set (Selectable Icons) lights are on.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 7. Brake Warning Light The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. This light monitors various brake functions, including brake fluid level and parking brake application.
156 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by cycling the ignition from the OFF position to the ON/ RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. 9. Oil Pressure Warning Light This light indicates low engine oil pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 12. Tire Pressure Monitoring Telltale Light — If reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
158 UNDERSTANDING YOUR INSTRUMENT PANEL alternate tires or wheels on the vehicle that prevent the 13. Malfunction Indicator Light (MIL) TPMS from functioning properly. Always check the The Malfunction Indicator Light (MIL) is part of TPMS malfunction telltale after replacing one or more an onboard diagnostic system, called OBD, that tires or wheels on your vehicle, to ensure that the monitors engine control systems.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions.
160 UNDERSTANDING YOUR INSTRUMENT PANEL 16. EVIC Amber Telltale Lights When the appropriate conditions exist, the following EVIC Amber Telltale Lights will display: • Windshield Washer Fluid Low Indicator — If Equipped This light will turn on to indicate the windshield washer fluid is low • Low Fuel Light When the fuel level reaches approximately 3.0 gal (11.0 L) this light will turn on, and remain on until fuel is added. 17.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 • Electronic Throttle Control (ETC) This telltale informs you of a problem with the Electronic Throttle Control (ETC) system. If the telltale comes on while driving, have the system checked by an authorized dealer. If a problem is detected, the telltale will come on while the engine is running. Cycle the ignition when the vehicle has completely stopped and the shift lever is placed in the NEUTRAL position and the parking brake applied. The telltale should turn off.
162 UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Temperature Warning Light This telltale indicates high engine oil temperature. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. • Door Ajar This telltale turns on when one or more doors are ajar. The telltale will show which doors are ajar. 19.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 Each time the ignition is cycled to ON/RUN, the ESC If the ABS light remains on or turns on while driving, it system will be ON, even if it was turned off previously. indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, The ESC system will make buzzing or clicking sounds the conventional brake system will continue to operate when it is active.
164 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) This system allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 • Vehicle Settings The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • UP Arrow Button Press and release the UP arrow button to scroll upward through the main menu and submenus (Fuel Economy, Trip A, Trip B, Audio, Stored Messages, Screen Set Up).
166 UNDERSTANDING YOUR INSTRUMENT PANEL • RIGHT Arrow Button Press and release the RIGHT arrow button to access/select the information screens or submenu screens of a main menu item. Press and hold the RIGHT arrow button for two seconds to reset displayed/selected features that can be reset. • LEFT Arrow Button Press the LEFT arrow button to return to the main menu from an info screen or sub-menu item.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 The EVIC displays are located in the center portion of the 8. Launch Control status when launch control mode is cluster and consists of the following sections: entered. The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages.
168 UNDERSTANDING YOUR INSTRUMENT PANEL the EVIC’s compass/outside temp line. Examples of this Electronic Vehicle Information Center (EVIC) message type are “Right Front Turn Signal Lamp Out” Messages and “Low Tire Pressure”. • Front Seatbelts Unbuckled • Unstored Messages • Driver Seatbelt Unbuckled This message type is displayed indefinitely or until the • Passenger Seatbelt Unbuckled condition that activated the message is cleared.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 • Cruise Ready • Right Turn Signal Light Out • Cruise Set To XXX MPH • Left Turn Signal Light Out • Tire Pressure Screen With Low Tire Pressure Warnings • Turn Signal On • Service Tire Pressure System • Service Airbag System • Parking Brake Engaged • Service Airbag Warning Light • Brake Fluid Low • Driver Seatbelt Unbuckled • Service Electronic Braking System • Passenger Seatbelt Unbuckled • Engine Temperature Hot • Front Seatbelts Unbuckled • Battery V
170 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Amber Telltales EVIC Red Telltales This area will show amber caution telltales. These tell- This area will show red telltales. These telltales include: tales include: • Door Ajar • Low Fuel Telltale This light will turn on to indicate that one or When the fuel level reaches approximately 3.0 gal more doors may be ajar. (11.0 L) this light will turn on, and remain on until fuel is added.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 Do not operate the vehicle until the cause is corrected. • Electronic Throttle Control (ETC) Light This light does not show how much oil is in the engine. This light informs you of a problem with the The engine oil level must be checked under the hood. Electronic Throttle Control (ETC) system. The • Charging System Light light will come on when the ignition is first cycled ON and remain on briefly as a bulb This light shows the status of the electrical chargcheck.
172 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Temperature Warning Light EVIC Green Telltales This light warns of an overheated engine condi- • Electronic Speed Control SET tion. As temperatures rise and the gauge apThis telltale will illuminate green when the proaches H, this indicator will illuminate and a single electronic speed control is SET. For further chime will sound after reaching a set threshold.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 Tachometer arrow button and Coolant Temp will be displayed. Press the UP or DOWN arrow button to scroll through the following information sub-menus: Press and release the UP or DOWN arrow button until the Tachometer icon is highlighted Tire Pressure in the EVIC. Press and release the RIGHT Press and release the UP or DOWN arrow button until arrow button to change the display between “Tire Pressure” is highlighted in the EVIC.
174 UNDERSTANDING YOUR INSTRUMENT PANEL Tire PSI is an information only function and cannot be Battery Voltage reset. Press and release the LEFT arrow button to return Press and release the UP or DOWN arrow button until to the main menu. “Battery Voltage” is highlighted in the EVIC. Press and Refer to “Tire Pressure Monitoring System (TPMS)” release the RIGHT arrow button and the battery voltage under “Starting and Operating” for further information. will be displayed. Coolant Temperature Intake Air Temp.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 Current Power 1/8 Mile Top Speed & Duration Press and release the UP or DOWN arrow button until Press and release the UP or DOWN arrow button until “Current Power” is highlighted in the EVIC. Press and the last 1/8 Mile Top Speed & Duration information is release the RIGHT arrow button and the current power displayed. will be displayed. Current G-Forces SRT Performance Info Press and release the UP or DOWN arrow button until the Current G-Forces are displayed.
176 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy Trip B Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted. Press the RIGHT arrow button and the next screen will display the following: Press and release the UP or DOWN arrow button until the Trip B icon is highlighted in the EVIC. Press and release the RIGHT arrow button to display the Trip B information.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 Stored Messages Vehicle Hibernation Press and release the UP arrow button until the Press and release the UP or DOWN arrow Messages display icon is highlighted in the button until the Hibernation icon is highlighted EVIC. This feature shows the number of stored in the EVIC. Press and release the RIGHT warning messages.
178 UNDERSTANDING YOUR INSTRUMENT PANEL • Average MPG • Average MPG • Current MPG • Current MPG • Trip A • Trip A • Trip B • Trip B • Coolant Temp. • Coolant Temp. • Oil Temp. • Oil Temp.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Uconnect™ ACCESS SETTINGS Customer Programmable Features — Uconnect™ The Uconnect™ Access system uses a combination of soft Access System Settings and hard keys located on the center of the instrument Press the Apps soft-key, then press the Settings soft-key panel that allows you to access and change the customer to display the menu setting screen. In this mode the Uconnect™ Access system allows you to access programprogrammable features.
180 UNDERSTANDING YOUR INSTRUMENT PANEL soft-key to close out of the settings screen. Pressing the setting soft-keys or by selecting any point on the scale Up or Down Arrow soft-keys on the right side of the between the + and – soft-keys. Then touch the arrow back screen will allow you to toggle up or down through the soft-key. available settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 • Units pressed. Touch the Touchscreen Beep soft-key until a check-mark appears next to the setting, showing that When in this display, you may select to have the EVIC, setting has been selected. Touch the back arrow soft-key odometer, and navigation system (if equipped) changed to return to the previous menu. between US and Metric units of measure.
182 UNDERSTANDING YOUR INSTRUMENT PANEL • Sync Time With GPS make your selection touch the + or - soft-keys to adjust the minutes up or down. Touch the back arrow soft-key When in this display, you may automatically have the to return to the previous menu or touch the X soft-key to radio set the time. To change the Sync Time setting touch close out of the settings screen. the Sync with GPS Time soft-key until a check-mark appears next to the setting, showing that setting has been • Time Format selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Safety / Assistance Lights After pressing the Safety / Assistance soft-key the fol- After pressing the Lights soft-key the following settings lowing settings will be available. will be available. • ParkView威 Backup Camera • Headlight Illumination On Approach Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE.
184 UNDERSTANDING YOUR INSTRUMENT PANEL your selection, touch the Headlights With Wipers softkey, next to setting, showing that setting has been selected. until a check-mark appears next to setting, showing that Touch the back arrow soft-key to return to the previous setting has been selected. Touch the back arrow soft-key menu. to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Remote Keyless Entry (RKE) transmitter. To make your selection, touch the Flash Lights With Lock soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. • Sound Horn With Lock When this feature is selected, the horn will sound when the Key Fob Lock button is pressed.
186 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Off Power Delay Compass Settings When this feature is selected, the power window switches, radio, Uconnect™ phone system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to OFF. Opening either front door will cancel this feature. To change the Engine Off Power Delay status touch the 0 seconds, 45 seconds, 5 minutes or 10 minutes soft-key.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 calibrate the compass by pressing the ON soft-key and completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the CAL indicator displayed in the EVIC turns off. The compass will now function normally. Audio After pressing the Audio soft-key the following settings will be available. • Balance/Fade Compass Variance Map When in this display you may adjust the Balance and Fade settings.
188 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Bass/Mid/Treble allow you to simply slide your • Paired Devices finger up or down to change the setting as well as touch This feature shows which phones are paired to the directly on the desired setting. Phone/Bluetooth system. For further information, refer • Speed Adjusted Volume to the Uconnect™ Access User’s Manual. This feature increases or decreases volume relative to SiriusXM™ Setup vehicle speed.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 • Subscription Information Uconnect™ ACCESS RADIOS – IF EQUIPPED New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM™ Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen in order to resubscribe. For detailed information on the Uconnect™ 3.0, Uconnect™ 5.0, Uconnect™ 8.4A or the Uconnect™ 8.
190 UNDERSTANDING YOUR INSTRUMENT PANEL This feature allows an iPod威 or external USB device to be The button located in the center of the right hand control will switch modes to Radio or other valid audio source. plugged into the USB port. iPod威 control supports Mini, 4G, Photo, Nano, 5G iPod威 The left hand control is a rocker type switch with a and iPhone威 devices. Some iPod威 software versions may pushbutton in the center. The function of the left hand not fully support the iPod威 control features.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 RADIO OPERATION AND MOBILE PHONES Automatic Temperature Control (ATC) Under certain conditions, the mobile phone being on in Hard-Keys your vehicle can cause erratic or noisy performance from The hard-keys located below the Uconnect™ Access your radio. This condition may be lessened or eliminated screen. by relocating the mobile phone antenna. This condition is not harmful to the radio.
192 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys Button Descriptions (Applies To Both Hard-keys And Soft-keys) Soft-keys are accessible on the Uconnect™ Access system 1. A/C Button screen. Press and release to change the current setting, the indicator illuminates when A/C is ON. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 4. Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is ON. Performing this function will cause the ATC to switch into manual mode. The blower speed may increase when Defrost mode is selected. If the front defrost mode is turned off the climate system will return the previous setting. 5.
194 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Modes The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The Mode settings are as follows: • Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 7. Blower Control 8. Climate Control OFF Button Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation. The speeds can be selected using either hard-heys or soft-keys as follows: Press and release this button to turn the Climate Control ON/OFF. Hard-key 9.
196 UNDERSTANDING YOUR INSTRUMENT PANEL 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the RECIRCULATION control button. Recirculation mode should only be used NOTE: temporarily.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 against engine overheating. A solution of 50% ethylene adequate system lubrication to minimize the possibility glycol antifreeze coolant and 50% water is recommended. of compressor damage when the system is started again. Refer to “Maintenance Procedures” in “Maintaining Your Window Fogging and Frosting Vehicle” for proper coolant selection. Vehicle windows tend to fog on the inside of the glass in Winter Operation mild, rainy and/or humid weather.
198 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .202 䡵 DRIVING ON SLIPPERY SURFACES . . . . . . . . .211 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .202 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . .211 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . .204 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . .205 䡵 DRIVING THROUGH WATER . . . .
200 STARTING AND OPERATING 䡵 BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . .218 䡵 TIRES — GENERAL INFORMATION. . . . . . . . .237 ▫ Brake Pad Break-In . . . . . . . . . . . . . . . . . . . .218 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .237 ▫ Anti-Lock Brake System . . . . . . . . . . . . . . . .219 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .238 䡵 ELECTRONIC BRAKE CONTROL SYSTEM . . . .222 ▫ Tire Pressures For High Speed Operation . . . .
STARTING AND OPERATING 201 䡵 TIRE PRESSURE MONITOR SYSTEM (TPMS) . .245 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . .252 ▫ Tire Pressure Monitoring Low Pressure 䡵 ADDING FUEL . . . . . . . . . . . . . . . . Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . .246 ▫ Emergency Fuel Filler Door Release. 䡵 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . .248 䡵 TRAILER TOWING . . . . . . . . . . . . . ▫ 8.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . .
202 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct any other occupant to buckle their seat belt. WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
STARTING AND OPERATING 203 NOTE: 3. Place the shift lever in NEUTRAL. • You must disarm the security system in order to start 4. Press the red ENGINE START/STOP button located on the instrument panel. Release the button when the the engine. Refer to “Security Alarm System” in engine starts. “Things To Know Before Starting Your Vehicle” for further information. • Normal starting of either a cold or a warm engine does not require pumping or pressing the accelerator pedal.
204 STARTING AND OPERATING If Engine Fails To Start WARNING! (Continued) CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. (Continued) • Do not attempt to push or tow your vehicle to get it started.
STARTING AND OPERATING 205 If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the “Normal Starting” procedure should be repeated. After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. MANUAL TRANSMISSION NOTE: The parking brake should be engaged and the shift lever placed into REVERSE before leaving the vehicle, especially when parked on an incline.
206 STARTING AND OPERATING CAUTION! Failure to start out in first gear when moving forward from a starting position may result in damage to the clutch. The spring will try to pull the shift lever toward third and fourth gear. Make sure you move the shift lever into second or fifth gear. If you let the shift lever move in the direction of the pulling, you may end shifting from first to fourth or from sixth to third gear. You will find it easier to use only the lower gears for most city driving.
STARTING AND OPERATING 207 NOTE: (clutch pedal released), but it may also be heard when driving. The noise may also be more noticeable when the transmission is warm. This noise is normal and is not an indication of a problem with your clutch or transmission. • Your vehicle is equipped with a transmission reverse inhibitor system. When vehicle speed is greater than 3 mph (5 km/h), the reverse inhibitor activates to help prevent shifts into REVERSE.
208 STARTING AND OPERATING cruise conditions (relatively steady speeds) will result in coolant is higher than 107°F (42°C), and vehicle speed is increased fuel economy, and may be used as indicated. greater than 16 mph (26 km/h) but less than 18 mph (29 km/h), and engine speed is less than 1,650 RPM, and MANUAL TRANSMISSION the transmission is in first gear, and the accelerator is at 20% throttle or less.
STARTING AND OPERATING 209 CAUTION! If you skip more than one gear while downshifting or downshift at too high a vehicle speed, you could damage the engine, transmission, or clutch. WARNING! Skipping more than one gear while downshifting, could cause you to lose control of your vehicle. You could have a collision. STREET/RACE MODE – IF EQUIPPED This vehicle is equipped with an electronic controlled damping system.
210 STARTING AND OPERATING • Race Mode — This mode is driver selectable when the 4. Press and release the “LAUNCH” Button (Located on the steering wheel controls). vehicle is placed in RACE mode (press the “RACE” button on the Instrument Panel). This mode is for track use only and will supply maximum grip to the tires. NOTE: The RACE setting will provide a firmer ride. • When RACE mode is enabled, a Shock symbol with “RACE” next to it will light up in the instrument cluster.
STARTING AND OPERATING 211 NOTE: If the cluster launch EVIC message indicates all DRIVING ON SLIPPERY SURFACES conditions are correct for launch and the throttle is Acceleration pressed to the floor quickly (within approximately 1/2 WARNING! second) the system will hold the engine speed to a preset speed (below the engine rev limiter speed). Rapid acceleration on slippery surfaces is dangerous. 6. Release the clutch.
212 STARTING AND OPERATING 2. Slow down if road has standing water or puddles. CAUTION! Driving your vehicle through deep puddles at speeds over 5 mph (8 km/h), may cause water to be ingested into the engine. This can cause severe engine damage. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop.
STARTING AND OPERATING 213 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
214 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 215 system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticidoes not in any way damage the steering system. pated. Coordinate inspection efforts through an authorized dealer. WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
216 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated The parking brake should always be applied when the level. With a clean cloth, wipe any spilled fluid from all driver is not in the vehicle. surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further informaWARNING! tion. Before leaving the vehicle, make sure you fully apply the parking brake and shift the transmission into PARKING BRAKE REVERSE.
STARTING AND OPERATING 217 drops into the handle (releasing the lock), guide the handle downward to its stop and then release the button and the handle. The “Brake System Warning Light” in the instrument cluster will turn on when the ignition is in the ON/RUN position and the parking brake is applied. NOTE: This light only shows that the parking brake is applied or a brake/ABS system fault. It does not show the degree of brake application.
218 STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the “Brake System Warning Light.” In the event power assist is lost for any reason (i.e.
STARTING AND OPERATING 219 Safe Operating Tips WARNING! (Continued) WARNING! To use your brakes and accelerator more safely, follow these tips: • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • When descending mountains or hills, repeated braking can cause brake fade with loss of braking control.
220 STARTING AND OPERATING NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the ABS is functioning. The ABS conducts a low-speed self-test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occurring, you may feel slight pedal movement. The movement can be more apparent on ice and snow. This is normal.
STARTING AND OPERATING 221 WARNING! (Continued) • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The Anti-Lock Brake System (ABS) cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
222 STARTING AND OPERATING the vehicle to a complete stop as soon as possible and cycle the ignition to attempt to reset the ABS. If the light remains on, see your authorized dealer immediately to have the system serviced. Also, if the “BRAKE Warning Light” and the “ABS Warning Light” are on, and the parking brake is fully released, see your authorized dealer immediately.
STARTING AND OPERATING 223 In full on mode ESC uses sensors in the vehicle to determine the path that the driver intends to steer the This system monitors the amount of wheel spin of each vehicle and compares it to the actual path of the vehicle. driven wheel.
224 STARTING AND OPERATING WARNING! The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents resulting from loss of vehicle control due to inappropriate driver input for the conditions.
STARTING AND OPERATING 225 message may appear in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle InformaESC On tion Center (EVIC)” in “Understanding Your Instrument This is the normal operating mode for the ESC. When- Panel” for further information. To turn ESC ON again, ever the vehicle is started, the ESC system will be in this momentarily press the “ESC Off” switch. mode. This mode should be used for most driving situations.
226 STARTING AND OPERATING the “ESC” switch twice. The “ESC Track Light” will illuminate, and the ⬙ESC TRACK⬙ message will display in Sport mode has reduced traction control and reduced the vehicle odometer. Refer to “Electronic Vehicle Inforstability control. To enter the “Sport Mode” mode, press mation Center (EVIC)” in “Understanding Your Instruthe “ESC” switch once (located on the steering wheel). ment Panel” for further information.
STARTING AND OPERATING 227 TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
228 STARTING AND OPERATING compact spare tires have the letter “T” or “S” molded • High flotation tire sizing is based on U.S. design into the sidewall preceding the size designation. Exstandards and it begins with the tire diameter molded ample: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING 229 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
230 STARTING AND OPERATING Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
STARTING AND OPERATING 231 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
232 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 233 Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading Tire and Loading Information Placard The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
234 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occuaxles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg” on your vehicle’s placard. “Vehicle Loading” in this section. 2.
STARTING AND OPERATING 235 5. Determine the combined weight of luggage and cargo NOTE: being loaded on the vehicle. That weight may not • The following table shows examples on how to calcusafely exceed the available cargo and luggage load late total load, cargo/luggage, and towing capacities capacity calculated in Step 4. of your vehicle with varying seating configurations 6. If your vehicle will be towing a trailer, load from your and number and size of occupants.
236 STARTING AND OPERATING
STARTING AND OPERATING 237 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
238 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Unequal tire pressures can cause erratic and unpredictable steering response.
STARTING AND OPERATING 239 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
240 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING 241 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
242 STARTING AND OPERATING Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING 243 Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall. See the Tire Sizing Chart example found in the Tire Safety Information section of this manual for more information relating to the Load Index and Speed Symbol of a tire. It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.
244 STARTING AND OPERATING WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. SNOW TIRES There are no snow tires that are compatible with the wheels on this vehicle.
STARTING AND OPERATING 245 Refer to the “Maintenance Schedule” for the proper maintenance interval. Remember, more frequent rotation is permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire rotation. NOTE: Each wheel on your vehicle contains a tire pressure sensor. The Tire Pressure Monitor System (TPMS) learns the location of each sensor though system programming.
246 STARTING AND OPERATING readings to the receiver module. It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. The TPMS consists of the following components: • Receiver module, • Four TPM sensors, • Various TPMS messages, which display in the Electronic Vehicle Information Center (EVIC), and • TPM Telltale Light The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor.
STARTING AND OPERATING 247 Service TPMS Warning 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. 3. Accumulation of snow or ice around the wheels or The system fault will also sound a chime. In addition, the wheel housings. EVIC will display a ⬙SERVICE TPM SYSTEM⬙ message 4. Using tire chains on the vehicle.
248 STARTING AND OPERATING FUEL REQUIREMENTS 8.4L Engine The 8.4L engine is designed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality premium unleaded gasoline with an octane rating of 91 or higher.
STARTING AND OPERATING 249 Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline containgenates such as Ethanol. Fuels blended with oxygenates ing 10% ethanol (E10). Gasoline with higher ethanol may be used in your vehicle. content may void the vehicle’s warranty. CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol.
250 STARTING AND OPERATING • disconnect and reconnect the battery to reset the therefore, you should ask your gasoline retailer whether the gasoline contains MMT. It is even more important to engine controller memory look for gasoline without MMT in Canada, because MMT More extensive repairs will be required for prolonged can be used at levels higher than those allowed in the exposure to E-85 fuel. United States. MMT is prohibited in Federal and CaliforMMT In Gasoline nia reformulated gasoline.
STARTING AND OPERATING 251 Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
252 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 253 4. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper door while refueling. NOTE: Only the correct size nozzle opens the latches allowing the flapper door to open. 5. Fill the vehicle with fuel – when the fuel nozzle “clicks” or shuts off the fuel tank is full. 6. Remove the fuel nozzle and close the fuel door.
254 STARTING AND OPERATING 3. Pull the release cable. Emergency Fuel Filler Door Release If you are unable to open the fuel filler door, use the fuel TRAILER TOWING filler door emergency release. Trailer towing with this vehicle is not recommended. 1. Open the trunk. 2. Remove the access cover (located on the right side inner trim panel). RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 255 NOTE: If the vehicle requires towing, make sure all four wheels are off the ground. GROUND CLEARANCE The front and rear fascias and side sills ride low and ground clearance is limited. CAUTION! Damage to the front and rear fascias and side sills can occur if you disregard the low ground clearance in these areas of your vehicle. Pay close attention when parking to avoid running into parking curbs.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHER . . . . . . . . . . .258 ▫ Sealing A Tire With TIREFIT . . . . . . . . . . . . . .264 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .258 䡵 JUMP-STARTING PROCEDURES . . . . . . . . . . .269 䡵 TIREFIT KIT . . . . . . . . . . . . . . . . . . . . . . . . . .259 䡵 FREEING A STUCK VEHICLE . . . . . . . . . . . . .273 ▫ TIREFIT Storage . . . . . . . . . . . . . . . . . . . . . .260 䡵 TOWING A DISABLED VEHICLE . . . . . . . . . . .
258 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the center of the instrument panel above the climate controls. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all direc- • On the highways — Slow down and use the highest gear possible.
WHAT TO DO IN EMERGENCIES 259 • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
260 WHAT TO DO IN EMERGENCIES TIREFIT Storage TIREFIT Kit Components And Operation The TIREFIT kit is located in left side of the trunk. TIREFIT Location TIREFIT Components 1. Sealant Bottle 2. Deflation Button 3.
WHAT TO DO IN EMERGENCIES 261 4. Power Button 5. Mode Select Knob 6. Sealant Hose (Clear) 7. Air Pump Hose (Black) 8. Power Plug Using The Mode Select Knob And Hoses Your TIREFIT kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Selecting Sealant Mode Turn the Mode Select Knob (5) to this position to inject the TIREFIT Sealant and to inflate the tire. Use the Sealant Hose (clear hose) (6) when selecting this mode.
262 WHAT TO DO IN EMERGENCIES • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the • Replace the TIREFIT Sealant Bottle (1) and Sealant TIREFIT kit. Hose (6) prior to the expiration date (printed on the bottle label) to assure optimum operation of the sys- • You can use the TIREFIT air pump to inflate bicycle tires. The kit also comes with two needles, located in tem.
WHAT TO DO IN EMERGENCIES 263 WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the TIREFIT kit. • Do not use TIREFIT or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4 in. (6 mm) or larger. – If the tire has any sidewall damage. – If the tire has any damage from driving with extremely low tire pressure.
264 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • TIREFIT Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. kit when injecting the sealant into the deflated tire and running the air pump.
WHAT TO DO IN EMERGENCIES 265 4. Remove the cap from the valve stem and then screw NOTE: Sealant may leak out through the puncture in the the fitting at the end of the Sealant Hose (6) onto the tire. valve stem. If the sealant (white fluid) does not flow within 0 – 10 5. Uncoil the Power Plug (8) and insert the plug into the seconds through the Sealant Hose (6): vehicle’s 12 Volt power outlet. 1. Press the Power Button (4) to turn Off the TIREFIT kit. NOTE: Do not remove foreign objects (e.g.
266 WHAT TO DO IN EMERGENCIES NOTE: If the Mode Select Knob (5) is on Air Mode and If the tire does not inflate to at least 26 psi (1.8 Bar) the pump is operating, air will dispense from the Air pressure within 15 minutes: Pump Hose (7) only, not the Sealant Hose (6). • The tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. If the sealant (white fluid) does flow through the Sealant Hose (6): NOTE: If the tire becomes over-inflated, press the Defla1.
WHAT TO DO IN EMERGENCIES 267 3. Immediately disconnect the Sealant Hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the TIREFIT kit in the vehicle storage location. Quickly proceed to (D) “Drive Vehicle”. (D) Drive Vehicle: Immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the TIREFIT Sealant within the tire. Do not exceed 55 mph (88 km/h).
268 WHAT TO DO IN EMERGENCIES 1. Turn the Mode Select Knob (5) to the Air Mode NOTE: If the tire becomes over-inflated, press the Deflaposition. tion Button to reduce the tire pressure to the recommended inflation pressure before continuing. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 Volt power outlet. 2. Disconnect the TIREFIT kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 3. Uncoil the Air Pump Hose (7) (black in color) and Volt outlet.
WHAT TO DO IN EMERGENCIES 269 (F) Sealant Bottle And Hose Replacement: 1. Uncoil the Sealant Hose (6) (clear in color). 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). 2. Locate the round Sealant Bottle release button in the 7. Return the TIREFIT kit to its storage location in the recessed area under the sealant bottle. vehicle. 3. Press the Sealant Bottle release button.
270 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way and may be damaged. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
WHAT TO DO IN EMERGENCIES 271 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles touch one another. 3. Set the parking brake, place the transmission in NEUTRAL, and turn the ignition OFF on both vehicles. 4. Turn off the heater, radio, and all unnecessary electrical loads. 5.
272 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 6. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 10.
WHAT TO DO IN EMERGENCIES 273 13. Disconnect the positive (+) jumper cable from the FREEING A STUCK VEHICLE positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand, or snow, it 14. Disconnect the positive (+) end of the jumper cable can often be moved using a rocking motion. Turn your from the remote positive (+) post of the discharged steering wheel right and left to clear the area around the front wheels. Then shift back and forth between 2nd gear vehicle.
274 WHAT TO DO IN EMERGENCIES CAUTION! (Continued) • Revving the engine or spinning the wheels too fast may lead to transmission or clutch overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring). WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 8.4L . . . . . . . . . .277 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .284 䡵 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . .278 ▫ Hibernation Mode . . . . . . . . . . . . . . . . . . . .286 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . .278 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .287 䡵 REPLACEMENT PARTS . . . . . . . . . . . . . . . . . .280 䡵 DEALER SERVICE . . . . . . . .
276 MAINTAINING YOUR VEHICLE ▫ Hydraulic Clutch . . . . . . . . . . . . . . . . . . . . .301 ▫ Front/Rear Side Marker Lamp . . . . . . . . . . . .319 ▫ Rear Axle . . . . . . . . . . . . . . . . . . . . . . . . . . .302 ▫ Taillamp, Tail/Stop Lamp . . . . . . . . . . . . . . . .319 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . .302 ▫ Rear Turn Signal Lamp . . . . . . . . . . . . . . . . .319 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 277 ENGINE COMPARTMENT — 8.
278 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! To meet new government regulations and promote cleaner air, your vehicle is equipped with a sophisticated Prolonged driving with the light on could cause onboard diagnostic system called OBD II. This system further damage to the emission control system. It monitors the performance of the emissions and engine could also affect fuel economy and driveability. The control systems.
MAINTAINING YOUR VEHICLE 279 Indicator Light (MIL)” is functioning and is not on when 3. As soon as you turn the ignition switch to the ON the engine is running, and that the OBD II system is position, you will see the MIL symbol come on as part ready for testing. of a normal bulb check. Normally, the OBD II system will be ready. The OBD II 4.
280 MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update. A recheck with the above test routine may then indicate that the system is now ready. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
MAINTAINING YOUR VEHICLE 281 MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future.
282 MAINTAINING YOUR VEHICLE check the oil level is approximately five minutes after a Engine Oil Selection fully warmed engine is turned off or before starting the For best performance and maximum protection under all engine after it has sat overnight. types of operating conditions, the manufacturer only Checking the oil while the vehicle is on level ground also recommends full synthetic engine oils that meet the will improve the accuracy of the oil level readings.
MAINTAINING YOUR VEHICLE 283 The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information. Materials Added To Engine Oil The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives.
284 MAINTAINING YOUR VEHICLE WARNING! CAUTION! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 285 WARNING! Battery Location • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
286 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE 287 3. Press and hold the right arrow button on the steering wheel controls for 1 second. Vehicle will countdown from ten seconds and enter Hibernation Mode. NOTE: You may press the right arrow button on the steering wheel controls during the countdown to abort Hibernation Mode. To Deactivate Hibernation Mode 1. Press the RKE UNLOCK button to unlock the vehicle. 2. Press the ignition switch to the ON/RUN position.
288 MAINTAINING YOUR VEHICLE WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
MAINTAINING YOUR VEHICLE 289 marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as necesClean the rubber edges of the wiper blades and the sary. windshield and rear window periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will Adding Washer Fluid remove accumulations of salt, waxes, or road film, and The windshield washer fluid reservoir is located in the help reduce streaking and smearing.
290 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE 291 CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
292 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- Cooling System age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
MAINTAINING YOUR VEHICLE 293 applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (antifreeze). Check the front of the A/C condenser/radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser/radiator. bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.
294 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).
MAINTAINING YOUR VEHICLE 295 period, it is important that you use the same engine Please note that it is the owner’s responsibility to maincoolant (antifreeze) throughout the life of your vehicle. tain the proper level of protection against freezing according to the temperatures occurring in the area where Please review these recommendations for using Organic the vehicle is operated. Additive Technology (OAT) engine coolant (antifreeze).
296 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 297 When additional engine coolant (antifreeze) is needed to • Check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (antimaintain the proper level, it should be added to the freeze) needs to be added, the contents of the coolant coolant bottle. Do not overfill. expansion bottle must also be protected against Points To Remember freezing.
298 MAINTAINING YOUR VEHICLE • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. Brake System WARNING! Riding the brakes can lead to brake failure and possibly an accident.
MAINTAINING YOUR VEHICLE 299 Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only the manufacturer’s recommended brake fluid.
300 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.
MAINTAINING YOUR VEHICLE 301 Manual Transmission Transmission Fluid Level Check Check the fluid in the transmission when performing other underbody services. CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or damage to the transmission. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for fluid specifications.
302 MAINTAINING YOUR VEHICLE manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Rear Axle Axle Lubricant Level Check Check the exterior of the axle for evidence of gear oil leakage every 12 months or 6,000 miles (10 000 km). This check should be made with the vehicle level and on the ground or raised on an axle and wheel type hoist.
MAINTAINING YOUR VEHICLE 303 highly corrosive to the metal in your vehicle. Outside • Use a high quality cleaner wax, such as MOPAR威 Cleaner Wax to remove road film, stains and to protect parking, which exposes your vehicle to airborne contamiyour paint finish. Take care never to scratch the paint.
304 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care Interior Care • All wheels and wheel trim, especially aluminum and Use MOPAR威 Total Clean to clean fabric upholstery and chrome plated wheels, should be cleaned regularly carpeting. with a mild soap and water to prevent corrosion. Use MOPAR威 Total Clean to clean vinyl upholstery. • To remove heavy soil and/or excessive brake dust, use MOPAR威 Total Clean is specifically recommended for MOPAR威 Wheel Cleaner. leather upholstery.
MAINTAINING YOUR VEHICLE 305 WARNING! Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear Leather or Vinyl Seat/Trim Care and Cleaning quarter window equipped with the radio antenna.
306 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses Replace the belts if they appear frayed or worn or if the buckles do not work properly. The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care Aero Group — If Equipped must be taken to avoid scratching the plastic. Please review all of the precautionary notes regarding the 1. Clean with a wet soft rag. A mild soap solution may be Aero Group option.
MAINTAINING YOUR VEHICLE 307 CAUTION! Use care when approaching parking blocks, tall speed bumps and garage curbs. These surfaces can damage your splitter. Use caution when driving up to sloped surfaces or over speed bumps. Approaching a speed bump or a slope at a slight angle may improve your clearance. CAUTION! Front Splitter Always leave ample room and be sure to educate anyone you allow to operate the vehicle. • Hard contact with steep ramps may cause damage to your splitter.
308 MAINTAINING YOUR VEHICLE FUSES Power Distribution Center The Power Distribution Center is located in the engine compartment on the driver’s side of the vehicle. This center contains fuses and relays.
MAINTAINING YOUR VEHICLE 309 Cavity Relay 3 4 5 6 7 8 9 10 11 12 — — — — — — — — — — 13 — Cartridge Fuse 40 Amp Green 40 Amp Green 40 Amp Green 40 Amp Green 40 Amp Green 40 Amp Green 30 Amp Pink 30 Amp Pink Jumper Black 25 Amp Natural — 14 — — Mini-Fuse Description — — — — — — — — — — Rad Fan Rad Fan Rly High ABS/ESP Pump Feed Starter CBC (Ext. Lighting #1) CBC (Ext. Lighting #2) CBC (Int.
310 MAINTAINING YOUR VEHICLE Cavity Relay 15 16 — — Cartridge Fuse — — 17 — — 18 19 20 21 22 23 24 — — — — — — — 30 Amp Pink 30 Amp Pink 30 Amp Pink 20 Amp Blue — Jumper Black — Mini-Fuse Description 10 Amp Red 15 Amp Blue 25 Amp circuit breaker — — — — — — 25 Amp Natural Diagnostic, Mirror, Fuel Door, Stop Switch KIN, RF Hub Power Seats Driver Door Mod Passenger Door Mod EBL Wiper B+ Jumper B+ Jumper PCM- Powertrain Control Module
MAINTAINING YOUR VEHICLE 311 Cavity Relay 25 — Cartridge Fuse — 26 — — 27 — — 28 29 30 — — — 31 32 33 — — — 34 — — 40 Amp Green 20 Amp Yellow — Jumper Black 20 Amp Yellow — Mini-Fuse Description 25 Amp Natural 20 Amp Yellow 20 Amp Yellow — — — Fuel Pump — — — B+ Jumper B+ Jumper Spare — B+ Jumper ASD #1 ASD #2 Spare HVAC Blower RR Power Outlet, Adj.
312 MAINTAINING YOUR VEHICLE Cavity Relay 35 36 37 — — — Cartridge Fuse Jumper Black — — Mini-Fuse Description Spare ORC Mod Run Cluster, Mirror, Camera — — — — 10 Amp Red 15 Amp Blue 20 Amp Yellow 10 Amp Red 15 Amp Blue — — 10 Amp Red 38 — — 39 40 — — — — 41 42 43AC (Forward Fuse) 43BE (Rearward Fuse) G8VA G8VA — — — 10 Amp Red Corax Active Damping Suspension HVAC Module, In Car Temp Radio Run/Start Fuel Door SCCM
MAINTAINING YOUR VEHICLE 313 Cavity Relay Mini-Fuse Description — Cartridge Fuse — 44BE (Rearward Fuse) 45 46 47 48 49 10 Amp Red IBS — — — — — — — — — — 10 Amp 10 Amp 10 Amp 10 Amp 25 Amp Natural — — — — — — PCM- Powertrain Control Module ESP Module ORC Module SCCM Amplifier 50 51 52 53 54 55 HC HC HC HC HC HC Micro Micro Micro Micro Relay Micro — — — — — — Red Red Red Red Rad Fan Rad Fan Relay SER/PAR Starter Relay EBL Relay Rad Fan Relay High Wiper ON/OFF 7
314 MAINTAINING YOUR VEHICLE Cavity Relay 56 HC Micro — G8VA G8VA HC Micro HC Micro G8VA G8VA HC Micro HC Micro G8VA 57 58 59 60 61 62 63 64 65 Cartridge Fuse — Mini-Fuse Description — Wiper LO/HI — — — — — — — — — — — — — — — — — — Horn Relay A/C Clutch Relay HVAC Blower Fuel Pump Run Relay #1 Run Relay #2 ASD #1 ASD #2 Run Accy #1, Pop Up
MAINTAINING YOUR VEHICLE 315 CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
316 MAINTAINING YOUR VEHICLE • Block the wheels. Do not apply the parking brake. • Cut blocks of plywood about the same size of the tires. Cover each block with indoor/outdoor carpeting and place them between the tires and concrete. This will prevent tire flat spotting. Then, either disconnect the battery at the negative terminal or use the “Battery Save Feature” to conserve battery power. Refer to “Maintenance Procedures/ Battery Save Feature” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 317 • Check the battery every four to six weeks to ensure 3. Make sure that the HOOD, LIFTGATE, and DOOR that the voltage is above 12.40 Volts. The voltage will switches are in adjustment. Perform the quick system drop more rapidly in hot temperatures. If battery check, which follows: voltage drops below 12.40 Volts, follow the battery Use the remote transmitter to set the alarm. If the alarm SET light comes on and flashes, the system is recharge procedure in the Service Manual.
318 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS Exterior Bulbs Interior Bulbs Message Center Indicators Cluster Gauge Pack Heater Control Interior Lamp Courtesy Foot Well Lights Cargo Lamp (Coupe Liftgate) Bulb Number 103 103 103 37 LED (Serviced at Authorized Dealer) 194 168 Low/High Beam Headlamp Front Park/Turn Signal Lamp Front Side Marker Lamp Center High Mounted Stop Lamp (CHMSL) Tail/Stop/Turn Signal Lamp Rear Marker Lamp Backup Lamp License Lamp Bulb Number LED (Serviced at Authorized Dealer) L
MAINTAINING YOUR VEHICLE 319 BULB REPLACEMENT Front Headlamp, Front Park/Turn Signal Lamp For bulb replacement, see your authorized dealer. 3. Pull the bulb out of the socket and insert the replacement bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. Front/Rear Side Marker Lamp 5. Reinstall the front/rear side marker. 1. Remove the front/rear side marker.
320 MAINTAINING YOUR VEHICLE Backup Lamps 5. Remove the bulb from the connector socket and install the replacement bulb. 1. Reach behind the rear bumper and press the release tabs on the backup lamp housing. 6. Reinstall the bulb and socket assembly into the backup lamp assembly, and then turn it clockwise. 2. Separate the backup lamp housing from the rear bumper fascia. 7. Reinstall the backup lamp housing into the rear bumper fascia. 3. Disconnect the electrical harness connector. 4.
MAINTAINING YOUR VEHICLE 321 FLUID CAPACITIES Fuel (Approximate) Engine Oil With Filter 8.4 Liter Engine – We recommend you use SAE 0W-40, API Certified. Transmission 8.4 Liter Engine – We recommend you use MOPAR威 ATF+4威 Automatic Transmission Fluid. Rear Axle We recommend you use Castrol SAF-XJ/SAE 75W-140 Synthetic Gear and Axle Lubricant. Cooling System * 8.4 Liter Engine – We recommend you use MOPAR威 Antifreeze/ Engine Coolant 10 Year/150,000 Mile Formula or equivalent.
322 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part We recommend you use MOPAR威 Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). We recommend you use a full synthetic 0W-40 or equivalent engine oil. We recommend you use MOPAR威 Engine Oil Filters. We recommend you use MOPAR威 Spark Plugs, see your authorized dealer.
MAINTAINING YOUR VEHICLE 323 Chassis Component Transmission Rear Axle Brake/Clutch Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part We recommend you use MOPAR威 ATF+4威 Automatic Transmission Fluid. We recommend you use Castrol SAF-XJ/SAE 75W-140 Synthetic Gear and Axle Lubricant. We recommend you use MOPAR威 Brake and Clutch Fluid DOT 4 Motor Vehicle. We recommend you use MOPAR威 Power Steering Fluid + 4, MOPAR威 or ATF+4威 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULES . . . . . . . . . . . . .326 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 326 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULES At Each Stop For Fuel The Scheduled Maintenance services listed in this • Check the engine oil level about five minutes after a manual must be done at the times or mileages specified fully warmed engine is shut off. Checking the oil level to protect your vehicle warranty and ensure the best while the vehicle is on level ground will improve the vehicle performance and reliability. More frequent mainaccuracy of the oil level reading.
MAINTENANCE SCHEDULES 327 M • Check all lights and all other electrical items for correct • Inspect the suspension components. operation. • Lubricate door hinges and check springs. At Each Oil Change • Check the engine coolant level, hoses, and clamps. • Change the engine oil filter. • Check power steering fluid level. • Inspect the exhaust system.
M 328 MAINTENANCE SCHEDULES A I 6,000 Miles (10,000 km) or 6 N T Months Maintenance Service E Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped).
MAINTENANCE SCHEDULES 329 M 18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Change the rear axle fluid. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped).
M 330 MAINTENANCE SCHEDULES A I 30,000 Miles (50,000 km) or 30 N T Months Maintenance Service E Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 331 M 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped). Inspect the brake linings, and replace if necessary.
M 332 MAINTENANCE SCHEDULES A I 54,000 Miles (90,000 km) or 54 N T Months Maintenance Service E Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Change the rear axle fluid. E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter.
MAINTENANCE SCHEDULES 333 M 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped). Inspect the brake linings, and replace if necessary.
M 334 MAINTENANCE SCHEDULES A I 78,000 Miles (130,000 km) or N T 78 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped).
MAINTENANCE SCHEDULES 335 M 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Inspect and replace the PCV Valve if necessary.* ❏ Change the rear axle fluid. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 336 MAINTENANCE SCHEDULES A I 102,000 Miles (170,000 km) or N T 102 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped).
MAINTENANCE SCHEDULES 337 M 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 338 MAINTENANCE SCHEDULES A I 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T ❏ Rotate tires. E ❏ Replace the engine air cleaner filter. N ❏ Replace the air conditioning filter (if equipped). A ❏ Flush and replace the engine coolant at 120 months or 150,000 miles (250 000 km) whichever comes first. N ❏ Inspect the brake linings, and replace if necessary. C E ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 339 M 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Change the rear axle fluid. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped).
M 340 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped).
MAINTENANCE SCHEDULES 341 M 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Flush and replace the engine coolant at 150,000 miles (250 000 km) or 120 months whichever comes first. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M A I N T E N A N C E S C H E D U L E S 8 342 MAINTENANCE SCHEDULES * This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .345 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .347 ▫ Prepare For The Appointment. . . . . . . . . . . . .345 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .347 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .345 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
344 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .351 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .351 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .352 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 345 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
346 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 347 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1 800 855-0511 to connect with a Bell Relay Service operator.
348 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 349 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR威 fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– operating at its best. 9153), or go to http://www.safercar.
350 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 351 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
352 IF YOU NEED CONSUMER ASSISTANCE Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
INDEX 10
354 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .218 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .219 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .294 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .252 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .289 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .250 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .125 Airbag. . . . . . . .
INDEX 355 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 Emergency Starting . . . . . . . . . . . . . . . . . . . . .269 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . .269 Keyless Transmitter Replacement (RKE) . . . . . . . .19 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 Saving Feature (Protection) . . . . . . . . . . . . . . . .286 Storing Vehicle . . . . . . . . . . . . . . . . . . . . . . . .286 Belts, Seat . . . . . . . . . . . . .
356 INDEX Clean Air Gasoline . . . . . . . . . . . . . Cleaning Wheels . . . . . . . . . . . . . . . . . . . Windshield Wiper Blades . . . . . . Climate Control . . . . . . . . . . . . . . . Clutch Fluid . . . . . . . . . . . . . . . . . . Contract, Service . . . . . . . . . . . . . . . Coolant Pressure Cap (Radiator Cap) Cooling System. . . . . . . . . . . . . . . . Adding Coolant (Antifreeze) . . . . Coolant Capacity . . . . . . . . . . . . Coolant Level . . . . . . . . . . . . . .
INDEX 357 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 Door Opener, Garage. . . . . . . . . . . . . . . . . . . . . . .133 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Emission Control System Maintenance . . . . . . . . . .278 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277 Driving Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .283 Through Flowing, Rising, or Shallow Break-In Recommendations . . . . . . .
358 INDEX Enhanced Accident Response Feature . . . . . . . . . . . .49 Fluid Level Checks Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 Brake . . . . . . . . . . . . . . . . . . . . Capacities . . . . . . . . . . . . . . . . . Exhaust Gas Caution. . . . . . . . . . . . . . . . . . . . . . . .28 Clutch Fluid . . . . . . . . . . . . . . . Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Cooling System . . . . . . . . . . . . . Exterior Lighting. . . . . . .
INDEX 359 .248 Hands-Free Phone (Uconnect™). . . . . . . . . . . . . . . .71 .248 Hazard Driving Through Flowing, Rising, or Shallow .321 Standing Water . . . . . . . . . . . . . . . . . . . . . . . .212 .308 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . .258 Garage Door Opener (HomeLink威) . . . . . . . . . . . . .133 Headlights Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . . .248 Delay . . . . . . . . . .
360 INDEX Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Keyless Go. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Hydraulic Clutch Fluid . . . . . . . . . . . . . . . . . . . . .301 Knee Bolster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Lane Change and Turn Signals . . . . . . . . . . . . . . . .118 Lap/Shoulder Belts. . . . . . . . . . . . . . . . . . . . . . . . .30 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 361 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . .156 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . .318 Parade Mode (Daytime Brightness) . . . . . . . . . .121 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Daytime Running . . . . . . . . . . . . . . . . . . . . . . .117 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . .153 Dimmer Switch, Headlight . . . . . . .
362 INDEX Low Tire Indicator . . . . . . . . . . . . . . . . . . . . . . . .245 Modifications/Alterations, Vehicle . . . . . . . . . . . . . . .7 Low Tire Pressure System . . . . . . . . . . . . . . . . . . .245 Monitor, Tire Pressure System . . . . . . . . . . . . . . . .245 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .288 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280 MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 363 Phone, Cellular. . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Phone, Hands-Free (Uconnect™) . . . . . . . . . . . . . . .71 Placard, Tire and Loading Information . . . . . . . . . .233 Power Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .218 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . .141 Steering . . . . . . . . . .
364 INDEX Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 Rear Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Rear Window Defroster . . . . . . . . . . . . . . . . . . . . .148 Rear Window Features . . . . . . . . . . . . . . . . . . . . .148 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . . .109 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . .254 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . .248 Refrigerant . .
INDEX 365 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Security Alarm (Theft Alarm). . . . . . . . . . . . . . . . . .14 Selection of Coolant (Antifreeze). . . . . . . . . . . . . . .322 Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . . .282 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . . .
366 INDEX Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . . .124 Time Delay, Headlight . . . . . . . . . . . . . . . . . . . . . .116 Tire and Loading Information Placard . . . . . . . . . . .232 TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . .
INDEX 367 Transmitter Programming (Remote Keyless Entry) . . .19 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . .17 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . . .59 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . . .241 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 Vehicle Modifications/Alterations . . . . . . . . . . . . . . .7 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .
368 INDEX Water Driving Through . . . . . . . . . . . . . . . . . . . . . . .212 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . .304 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . .304 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . .197 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . . .
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
Chrysler Group LLC Chrysler Group LLC 13ZD-126-AA 13ZD-126-AA OWNER’S MANUAL Printed in U.S.A. Printed in U.S.A. 1st Edition First Edition 1135554cv1 Viper 13ZD-126-AA Chrysler 1" gutter 07/11/2012 15:40:46 2013 Viper 2013 OWNER’S MANUAL Chrysler Group LLC 13ZD-126-AA First Edition Printed in U.S.A.
