Owner's Manual
On
Solid
Communication successfully established with
the
Directed
remote start or Directed digital
system.
White
LED*
Off
No
GPS
fix established.
Blinking
The
module
is
seeking for
GPS
satellites.
On
Solid
GPS
fix acquired.
*
The
green
LED
does not light if connected
to
Autostart/ AstroStart
systems
with
pager ports, or
in
standalone mode.
Note
(DSM550/VSM550
only):
In
order to save power, all three
LEDs
are
switched
to
slow pulse mode after 2
hours
of no activity. Also, when
the
de-
vice
enters
GPS
sleep mode, all
three
LEDs
are turned off completely.
The
radio
remains active
in
that mode, but
the
GPS
receiver
is
cycled to reduce power
consumption.
You
may have
to
power cycle
the
module
to
check
the
LED
status.
Note:
SmartStart response time can vary depending
on
cellular coverage and
net-
work congestion. Operating temperature range:
-40°C/-40°F
to+
70°C/
l 58°F.
lldna
Schenmtic
Orange .
f
Green
(Data
Connection)
(Networ~~
r:::;::sstatus)
LED
(
THIS
SIDE
UP)
~~t
Ct
c==>
Configuration
Wires
(Gray
& White) N/C
Wiring
Tobie
6-pin
Analog
Output
Cable
Pin#
Wire
Color
Connection/Description
l White/Blue
1-1
Remote
Start
Activation
AUX
output
1200mAI
2
Brown/Black
1-1
Alarm
input
3
Green
1-1
Lock
output
(200mAI
4
Blue
(-1
Unlock
output
(200mAI
5
Red/White
1-1
Trunk
output
1200mAI
6
Brown/Red
l+I
Alarm
input
Notes:
•
The
analog output wires are only active if
the
device
has
bee,:,
configured for
Analog
Wire
mode
in
the
installation portal.
•
For
Analog
Wire
mode, please make
sure
the
white wire
is
connected
to
ground.
* Do
not
cQnnect power and ground
wben__using
SmartStart
in a
D2D
configuration
or
damage may occur.
Red:+U\L*
------
Black:
Ground*
,--------..
Configuration
Wires
(Gray
& White}
c==>
LED
c==>
Connect Gray wire
to
(-)
Ground
(
THIS
SIDE
UP)
~~f
~f-
c==>
c==>
* Do
not
connect power and ground when using SmartStart
in a D2D configuration
or
damage may occur.
c==>
LED
~----~
Configuration
Wires
(Gray
& White)
c==>
Connect Gray wire
to
(-}
Ground
(
THIS
SIDE
UP)
~~f
~f
c==> c==>
* Do
not
connect power and ground when using SmartStart
in a
D2D
configuration or damage may occur.
see table)
P
(4
pins, Brown)
P
(3
pins,
Black)
[
SmartStart
Cable
- r
D2D
(4 pins, White)
Red:
+12V*
N/C
...._
_____
Black:
Ground*
N/C
SmartStart
Cable
D2D
(4 pins, White}
Red:
+
12V
*
N/C
------
Black:
Ground*
N/C
L
Ill Ill
111111
D83
(Top
View}
Directed
Digital System
(Top View)
u
0
QRNDSM550-VSM550,
510.10653-01
(R1
.0)