User Manual Preface This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer, Jan 2012. Trademarks Other product names mentioned herein are used for identification purpose only and may be trademarks and/or registered trademarks of their respective companies.
Foreword & Important Note on Safety!! (MUST READ) Please read this note before you install and use MB-4 Bluetooth Upgrade Adaptor! Congratulation on your MB-4! ViseeO MB-4 is the latest and one of the simplest Bluetooth Handsfree System ever designed for your Mercedes Benz. You will be able to connect the latest mobile phones to the handsfree system, sync phonebook and dial/answer a call from vehicle's original steering wheel control or headunit keypads.
QUICK START GUIDE CAUTION!! DO NOT ATTEMPT TO INSTALL THE UNIT WHILE THE CAR IS IN MOTION! INSTALLING MB-4 (For detailed instruction please see Section 2.1 Installing the Main Unit) 1. Make sure the engine is off. 2. Locate your UHI/MHI connector (It is usually situated in the tray under the front armrest). 3. Make sure there is no cradle attached to the UHI/MHI connector. 4. Press and hold MB-4 UHI release button then, gently slides MB-4 onto the UHI/MHI connector until in lock into the connector. 5.
MAKING A CALL (For detailed instruction please see Section 3.4 Making the First Call) 1. Connect your phone with MB-4. 2. Dial a set of numbers you wish to call using the numeric keypad on your Comand console. 3. Press the answer button on your Comand console to make a phone call. 4. To end the call, press the hang up button on your Comand console to end the call. SYNC FOR THE 1ST TIME (For detailed instruction please see Section 4.1 Sync Phonebook) 1. Connect your phone with MB-4. 2.
Preface................................................................................................................................. 1 Foreword & Important Note on Safety!! (MUST READ) .................................................................... 2 QUICK START GUIDE .............................................................................................................. 3 1. Understanding Your MB-4 ..............................................................................................
1. Understanding Your MB-4 1.1 Package Contents 1. MB-4 main unit. 2. USB to mini USB cable. 3. ViseeO Software Upgrade Cable.
1.2 MB-4 Main Unit & Descriptions Power Indicator OLED Display Menu/Confirm Button SYNC now/ Return/Cancel Button Quick Switch for Paired Phones/Menu Browsing Button 5V Mini USB Charging Port Software Dip Switch UHI Compatible Socket UHI Release Button CPU Software Upgrade Port 1.
1.4 MB-4 Keypads and Functions Each key corresponds to a designated command shown on the display Left Key Middle Key Right key SYNC Now, Return to Upper Level Menu, Cancel, Mic Volume Down Main Menu, Confirm, Save, Setup, OK, Delete Switch to Next Paired Phone, Browse Next Menu Item, Yes, Mic Volume Up << HTC 7 MOZART Connected SYNC MENU P2 1.5 Software Dip Switch and NTG 4 Vehicles (W204, W212, W207, etc.
The factory default setting has the both dip switches 1 & 2 at the “ON” position (see the illustration below) and this software setting is designed to work with Audio 20/Audio 50/COMAND APS NTG1 and NTG2 types of head units Original software switch position for Non-NTG4 vehicles Newer vehicles such as W204, W212, some of the GLK and W207 Coupe which comes with a newer type of UHI/MHI Comand system (NTG 4) that requires different type of software to work with.
2. Installation 2.1 Installing the Main Unit ViseeO MB-4 is designed to work with a pre-installed UHI/MHI Comand system in your vehicle. Therefore, you will need to locate the UHI/MHI connector which is normally found in the tray under the front armrest. If there is a phone cradle attached to the UHI/MHI connector, please remove it first. To remove the cradle: 1. Please make sure the vehicle engine is off. 2. Press the release button on your cradle (normally located at the top). 3.
3. Basic Operation 3.1 Pairing for the First Time Once you have installed your MB-4 in the vehicle, you need to pair it with your mobile phone. To pair your mobile phone with MB-4 for the first time: 1. Press [MENU] in standby mode. 2. Browse with [ ] to BLUETOOTH and press [SETUP] to enter the Bluetooth setting. 3. Browse with [ ] to PAIRING and press [SETUP] to enter pairing mode. The OLED screen should display 'PAIRING NOW... Search ViseeO on your phone'. 4.
order to allow automatic reconnection each time you re-enter your vehicle please select “Yes” when you see this type of messages. Due to the variation in phone’s Bluetooth setting and its operating software not all phones can be paired or connected with MB-4 smoothly. We endeavour to make sure all major Bluetooth mobile phones are compatible with MB-4. However, with the new phones or less popular phones there is still a possibility that MB-4 may not pair, connect properly or smoothly.
If you switch to a phone that is not nearby or its Bluetooth is not switched on you will get a message “Not found” and followed by “No Phone Device” after 90 seconds of attempting to make connection. You can always check what phones are already paired and what are their assigned number in Reconnect a Paired Device menu under the Bluetooth Setting (see Section 5.2 Reconnect a Paired Device for further information) 3.4 Making the First Call To make your first call: 1.
4. Phonebook Function 4.1 Sync Phonebook If your phone supports the phonebook sync protocol provided by MB-4 you will be able to take the advantage of the automatic phonebook upload function. The phonebook sync process is divided into two stages: 1. From phone to MB-4. 2. From MB-4 to Comand console. As soon as your phone is connected with MB-4 it will upload contacts in your phone memory to the MB-4’s memory. When this is completed MB-4 will then transfer the contacts to the Comand system.
phonebook entries under Object Push Profile (OPP) mode (see Section 4.2 Manually Upload Phonebook for further information). Phonebook sync speed varies between phone models and size of the phonebook. For some phones, the synchronization to MB-4 is almost instant but for others it may take longer. The transfer from MB-4 to Comand APS may take a while depending on the phonebook size. Once transfer is completed you will be able to see the phonebook entries when accessing the Phonebook screen.
2. Browse with [ ] to [SEND CONACT]. 3. Press [OPP] to activate OPP mode. 4. Access your phonebook on your phone now and go to the required contact entry. 5. Choose Option on your phone screen and select Send via Bluetooth (or similar term) and select MB-4 as the device to transfer the contact to. 6. Repeat the Step 4 and 5 for other entries if necessary. 7. Once you have finished, press [OK] to stop OPP mode.
To upload phonebook entries from MB-4 to NTG 4: 1. After connecting MB-4 with your mobile phone wait for “Activating Telephone…” message to disappear from your Comand screen. 2. Press Telephone command on the Comand console. 3. Select Import External Data command on the Comand console. Comand console will now begin the phonebook transfer. Once completed the entries will emerge in the phonebook on the Comand screen. This works the same for uploading the phonebook under the OPP mode.
phone. If you wish to skip the auto sync of your phonebook every time you re-enter your car you can turn this function OFF. To enable/disable automatic phonebook sync: 1. Press [MENU] in the standby mode. 2. Browse with [ ] to PHONEBOOK and press [SETUP] to enter the phonebook setting. 4. Press [ON]/[OFF] to enable or disable automatic phonebook sync function. Tips: You can instantly tell whether automatic sync is on from the << sign in the standby mode.
5. Advanced Bluetooth Setting 5.1 Disconnect from the Current Connected Device To disconnect from the current connected device: 1. Press [MENU] in the standby mode. 2. Browse with [ ] to BLUETOOTH and press the [SETUP] to enter the Bluetooth setting. 3. Browse with [ ] to ACTIVE DEVICE and press [SETUP] to enter this setting. 4. Press [YES] to disconnect current device. Note: This function will only temporary disconnect the link between MB-4 and your phone.
5.3 Remove a Paired Device To remove a paired device: 1. Press [MENU] in standby mode. 2. Browse with [ ] to BLUETOOTH and press the [SETUP] to enter the Bluetooth setting. 3. Browse with [ ] to DELETE A PAIRED DEVICE and press [SETUP] to enter this setting. 4. Scroll with [ ] to select the device you want to remove and press [ ] to delete.
6. Other Advanced Settings 6.1 Microphone Volume Setting To setup microphone volume: 1. Press [MENU] in the standby mode. 2. Browse with [ ] to MIC VOLUME and press [SETUP] to enter the microphone volume setting. 3. Press [＋] or [－] to adjust the microphone volume and press [SAVE] to confirm. Note: Microphone quality may vary between car models.
the phonebook entries, ViseeO MB-4 allows you to reset it back to the original factory settings. To master reset ViseeO MB-4: 1. Press [MENU] in the standby mode. 2. Browse with [ ] to FACTORY DEFAULT and press [SETUP] to enter the factory default setting. 3. Press [CONFIRM] to confirm or [Ø]to cancel. CAUTION!! If you master reset the MB-4, all phonebook entries and paired settings will be erased. 6.4 Firmware Update and Version Check To check current firmware and software version: 1.
is the operating system of MB-4. Both types of updates may be revised from time to time and available for you to download from www.viseeo.com. You can always check your firmware and software version number on MB-4 against the latest firmware and software updates on www.viseeo.com to see if you have the most up-to-date Bluetooth firmware and CPU software.
2. Browse with [ ] to PIN SELECTION and press [SETUP] to enter this setting. 3. Press [SEL] to choose either PIN:1234 or PIN:0000. 4. Press [ ] to return to the upper level menu. Note: If you have a Samsung Galaxy phone such as Galaxy W, R or S2 you must change the PIN code to 0000 before you can use it. Once you have selected PIN code to 0000 you must also enter 0000 when prompt a pass code request during pairing. 6.6 Using the Charging Function Each MB-4 is equipped with a 5V charging port.
7. Miscellaneous 7.1 Trademark The Bluetooth logos are registered trademarks owned by Bluetooth SIG, Inc, and any use of such marks in this document is under license. All other trademarks are the property of their respective owners, and are solely used to identify their respective products, and have no indication of any affiliation or relationship. 7.2 Product Information Model No.: MB-4 Product Description: ViseeO Bluetooth Upgrade Adaptor Main Unit: Dimension: 125mm x 50mm x 27mm (Approx.) Weight: 83.
