Datasheet

IL300
www.vishay.com
Vishay Semiconductors
Rev. 2.0, 05-Mar-18
3
Document Number: 83622
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• Minimum and maximum values were tested requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements
(1)
Bin sorting: K3 (transfer gain) is sorted into bins that are ± 6 %, as follows:
Bin A = 0.557 to 0.626
Bin B = 0.620 to 0.696
Bin C = 0.690 to 0.773
Bin D = 0.765 to 0.859
Bin E = 0.851 to 0.955
Bin F = 0.945 to 1.061
Bin G = 1.051 to 1.181
Bin H = 1.169 to 1.311
Bin I = 1.297 to 1.456
Bin J = 1.442 to 1.618
K3 = K2/K1. K3 is tested at I
F
= 10 mA, V
det
= -15 V
(2)
Bin categories: All IL300s are sorted into a K3 bin, indicated by an alpha character that is marked on the part. The bins range from “A”
through “J”.
The IL300 is shipped in tubes of 50 each. Each tube contains only one category of K3. The category of the parts in the tube is marked on
the tube label as well as on each individual part
(3)
Category options: standard IL300 orders will be shipped from the categories that are available at the time of the order. Any of the ten
categories may be shipped. For customers requiring a narrower selection of bins, the bins can be grouped together as follows:
IL300-DEFG: order this part number to receive categories D, E, F, G only
IL300-EF: order this part number to receive categories E, F only
IL300-E: order this part number to receive category E only
Note
• As per IEC 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with
the safety ratings shall be ensured by means of protective circuits
PHOTOCONDUCTIVE OPERATION
Frequency response I
Fq
= 10 mA, MOD = ± 4 mA, R
L
= 50 Ω BW (-3 db) - 200 - kHz
Phase response at 200 kHz V
det
= -15 V - -45 - Deg.
SWITCHING CHARACTERISTICS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Switching time ΔI
F
= 2 mA, I
Fq
= 10 mA
t
r
-1-μs
t
f
-1-μs
Rise time t
r
-1.75- μs
Fall time t
f
-1.75- μs
COMMON MODE TRANSIENT IMMUNITY
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Common mode capacitance V
F
= 0 V, f = 1 MHz C
CM
-0.5-pF
Common mode rejection ratio f = 60 Hz, R
L
= 2.2 kΩ CMRR - 130 - dB
SAFETY AND INSULATION RATINGS
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Climatic classification According to IEC 68 part 1 55 / 100 / 21
Comparative tracking index CTI 175
Maximum rated withstanding isolation voltage t = 1 min V
ISO
4420 V
RMS
Maximum transient isolation voltage V
IOTM
10 000 V
peak
Maximum repetitive peak isolation voltage V
IORM
890 V
peak
Isolation resistance
V
IO
= 500 V, T
amb
= 25 °C R
IO
≥ 10
12
Ω
V
IO
= 500 V, T
amb
= 100 °C R
IO
≥ 10
11
Ω
Output safety power P
SO
400 mW
Input safety current I
SI
275 mA
Safety temperature T
S
175 °C
Creepage distance ≥ 7mm
Clearance distance ≥ 7mm
Insulation thickness DTI ≥ 0.4 mm
ELECTRICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT