Datasheet

ManualsBrandsVishay ManualsOpto- & Photo CouplersOptocoupler DIP-8

Table Of Contents

Optocoupler, Phototransistor Output (Dual, Quad Channel)

VISHAY

ILD1/ 2/ 5 / ILQ1/ 2/ 5

Document Number 83646

Rev. 1.3, 10-Jun-04

Vishay Semiconductors

www.vishay.com

i179012

Dual Channel

Quad Channel

Optocoupler, Phototransistor Output (Dual, Quad Channel)

Features

• Current Transfer Ratio at I

= 10 mA

• Isolation Test Voltage, 5300 V

RMS

Agency Approvals

• UL - File No. E52744 system Code H or J

• CSA 93751

• BSI IEC60950 IEC60965

• DIN EN 60747-5-2 (VDE0884)

DIN EN 60747-5-5 pending

Available with Option 1

• FIMKO

Description

The ILD1/ 2/ 5/ ILQ1/ 2/ 5 are optically coupled iso-

lated pairs employing GaAs infrared LEDs and silicon

NPN phototransistor. Signal information, including a

DC level, can be transmitted by the drive while main-

taining a high degree of electrical isolation between

input and output. The ILD1/ 2/ 5/ ILQ1/ 2/ 5 are espe-

cially designed for driving medium-speed logic and

can be used to eliminate troublesome ground loop

and noise problems. Also these couplers can be used

to replace relays and transformers in many digital

interface applications such as CTR modulation.

The ILD1/ 2/ 5 has two isolated channels in a single

DIP package and the ILQ1/ 2/ 5 has four isolated

channels per package.

Order Information

For additional information on the available options refer to

Option Information.

Part Remarks

ILD1 CTR > 20 %, DIP-8

ILQ1 CTR > 20 %, DIP-16

ILD2 CTR > 100 %, DIP-8

ILQ2 CTR > 100 %, DIP-16

ILD5 CTR > 50 %, DIP-8

ILQ5 CTR > 50 %, DIP-16

ILD1-X007 CTR > 20 %, SMD-8 (option 7)

ILD1-X009 CTR > 20 %, SMD-8 (option 9)

ILD2-X006 CTR > 100 %, DIP-8 400 mil (option 6)

ILD2-X007 CTR > 100 %, SMD-8 (option 7)

ILD2-X009 CTR > 100 %, SMD-8 (option 9)

ILD5-X009 CTR > 50 %, SMD-8 (option 9)

ILQ1-X009 CTR > 20 %, SMD-16 (option 9)

ILQ2-X009 CTR > 100 %, SMD-16 (option 9)

Summary of content (10 pages)

PAGE 1
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Optocoupler, Phototransistor Output (Dual, Quad Channel) Features Dual Channel • Current Transfer Ratio at IF = 10 mA • Isolation Test Voltage, 5300 VRMS Agency Approvals UL - File No.
PAGE 2
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Absolute Maximum Ratings Tamb = 25 °C, unless otherwise specified Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Rating for extended periods of the time can adversely affect reliability.
PAGE 3
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Electrical Characteristics Tamb = 25 °C, unless otherwise specified Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Input Typ. Max Forward voltage Parameter IF = 60 mA Test condition VF 1.25 1.65 V Reverse current VR = 6.0 V IR 0.
PAGE 4
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Switching Non-saturated Parameter Current Delay Rise time Storage Symbol IF tD tr tS Unit mA µs µs µs ILD1 ILQ1 20 0.8 1.9 0.2 ILD2 ILQ2 5.0 1.7 2.6 ILD5 ILQ5 10 1.7 Current Delay Symbol IF tD Fall time Propagation H-L Propagation L-H tf tPHL tPLH µs µs µs 1.4 0.7 1.4 0.4 2.2 1.2 2.3 2.6 0.4 2.2 1.1 2.5 Rise time Storage Fall time Propagation H-L Propagation L-H tPHL tPLH VCE = 5.
PAGE 5
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Typical Characteristics (Tamb = 25 °C unless otherwise specified) F=10 KHz, DF=50% VCC=5 V VCC=5 V RL IF=10 mA VO IF=10 mA VO R L=75 Ω F=10 KHz, DF=50% iild1_01 iild1_03 Figure 1. Non-saturated Switching Schematic Figure 3. Saturated Switching Schematic IF IF t PHL VO tPLH VO tS tD tR VTH=1.5 V 50% tPHL iild1_02 tD tR Rev. 1.3, 10-Jun-04 tS tF tF Figure 2.
PAGE 6
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors 1.5 1.3 CTR - Normalized CTR Factor V F - Forward Voltage - V 1.4 TA = -55°C 1.2 TA = 25°C 1.1 1.0 0.9 TA = 100°C 0.8 0.7 Normalized to: VCE = 10 V, IF = 10 mA TA= 25°C 1.0 CTRce(sat) VCE = 0.4 V TA= 70°C NCTR 0.5 NCTR(SAT) 0.0 .1 1 10 I F - Forward Current - mA 100 .1 1 10 100 I F - LED Current - mA iild1_08 Figure 5. Normalized Non-Saturated and Saturated CTR vs. LED Current Figure 8. Normalized Non-Saturated and Saturated CTR vs.
PAGE 7
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors 1000 10 4 10 3 10 2 Vce = 10 V 10 1 Typical 10 0 10 -1 10 -2 -20 2.5 Ta = 25°C, IF = 10 mA Vcc = 5 V, Vth = 1.5 V tpHL 2.0 100 10 1.5 tpLH 1 0 20 40 60 80 100 tpHL - Propagation High-Low µs tpLH - Propagation Low-High µs ICEO - Collector-Emitter - nA 10 5 1.0 .1 1 TA - Ambient Temperature - °C 10 100 RL - Collector Load Resistor - kΩ iild1_11 iild1_12 Figure 11. Collector-Emitter Leakage Current vs.Temp. Figure 12.
PAGE 8
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Package Dimensions in Inches (mm) pin one ID 8 7 6 5 4 3 2 1 .255 (6.48) .265 (6.81) 9 10 11 12 13 14 15 16 ISO Method A .779 (19.77 ) .790 (20.07) .030 (.76) .045 (1.14) .300 (7.62) typ. .031(.79) .130 (3.30) .150 (3.81) 4° .018 (.46) .022 (.56) .020(.51) .035 (.89) .100 (2.54)typ. .050 (1.27) 10° typ. 3°–9° .008 (.20) .012 (.30) .110 (2.79) .130 (3.30) .230 (5.84) .250 (6.35) i178007 Option 6 Option 7 .407 (10.36) .391 (9.
PAGE 9
ILD1/ 2/ 5 / ILQ1/ 2/ 5 VISHAY Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operatingsystems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment.
PAGE 10
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.