Datasheet

ManualsBrandsVishay ManualsCapacitorsTantalum Capacitor with Polymer Cathode 22uF ±20% 6.3V

T58

www.vishay.com

Vishay

Revision: 09-Apr-2019

Document Number: 40189

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

vPolyTan

Polymer Surface Mount Chip Capacitors,

Compact, Leadframeless Molded Type

DESIGN SUPPORT TOOLS AVAILABLE

PERFORMANCE / ELECTRICAL

CHARACTERISTICS

Operating Temperature: -55 °C to +105 °C

Capacitance Range: 1 μF to 330 μF

Capacitance Tolerance: ± 20 %

Voltage Rating: 6.3 V

to 35 V

FEATURES

•Low ESR

• 100 % surge current tested

• Accelerated voltage conditioning

• High ripple current capability

• High volumetric efficiency

• Stable capacitance in operating temperature

range

• Better capacitance stability vs. frequency

• No wear out effect

• Molded case available in 8 case codes including 0603 and

0805 footprint

• Lead (Pb)-free L-shaped face-down terminations

• 8 mm tape and reel packaging available per EIA-481

standard

• Moisture sensitivity level 3

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

APPLICATIONS

• Decoupling, smoothing, filtering

• Bulk energy storage in wireless cards

• Infrastructure equipment

• Storage and networking

• Computer motherboards

• Smartphones and tablets

3D Models

Models

Calculators

ORDERING INFORMATION

T58 MM 106 M 6R3 C 0300

TYPE CASE

CODE

CAPACITANCE CAPACITANCE

TOLERANCE

DC VOLTAGE RATING TERMINATION /

PACKAGING

ESR

See

Ratings

and

Case

Codes

table.

This is expressed in

picofarads. The first

two digits are the

significant figures.

The third is the

number of zeros

to follow.

M = ± 20 % This is expressed in

volts. To complete the

three-digit block, zeros

precede the voltage

rating. A decimal point

is indicated by an “R”

(6R3 = 6.3 V)

C = lead (Pb)-free

solderable coating,

7" reel

Maximum

100 kHz ESR

in m

Summary of content (16 pages)

PAGE 1
T58 www.vishay.com Vishay vPolyTanTM Polymer Surface Mount Chip Capacitors, Compact, Leadframeless Molded Type FEATURES • Low ESR • 100 % surge current tested • Accelerated voltage conditioning • High ripple current capability • High volumetric efficiency • Stable capacitance in operating temperature range • Better capacitance stability vs.
PAGE 2
T58 www.vishay.com Vishay DIMENSIONS in inches [millimeters] Anode Polarity Bar Anode Termination W C P1 Cathode Termination P2 H P1 L CASE CODE EIA SIZE H (MAX.) L W P1 P2 (REF.) C MM 1608-09 0.035 [0.9] 0.063 ± 0.008 [1.6 ± 0.2] 0.033 ± 0.008 [0.85 ± 0.2] 0.020 ± 0.004 [0.5 ± 0.1] 0.024 [0.6] 0.024 ± 0.004 [0.6 ± 0.1] M0 1608-10 0.039 [1.0] 0.063 ± 0.008 [1.6 ± 0.2] 0.033 ± 0.008 [0.85 ± 0.2] 0.020 ± 0.004 [0.5 ± 0.1] 0.024 [0.6] 0.024 ± 0.004 [0.6 ± 0.
PAGE 3
T58 www.vishay.com Vishay MARKING Wx-Case Polarity bar Mx-Case Bx-Case Ax-Case Polarity bar Voltage code EIA capacitance code (pF) Capacitance code Polarity bar J107 + Polarity bar J JA + M0-Case Voltage code Polarity bar Voltage Capacitance code code + 330 6 2 VOLTAGE CODE V 6.3 8.2 10 16 25 35 Voltage code Vishay marking CAPACITANCE CODE CODE J k A C E V CAP, μF 1 4.
PAGE 4
T58 www.vishay.com Vishay RECOMMENDED VOLTAGE DERATING GUIDELINES CAPACITOR VOLTAGE RATING 6.3 8.2 10 16 25 35 OPERATING VOLTAGE 5.7 7.4 9.0 12.8 20 28 CAPACITANCE VS. FREQUENCY Axis Title 10000 220 μF - 10 V BB 100 1000 100 μF - 6 V A0 1st line 2nd line 2nd line Capacitance (μF) 1000 47 μF - 6 V M0 10 100 22 μF - 6 V MM 1 0.01 0.1 1 10 100 10 10 000 1000 Frequency (kHz) IMPEDANCE AND ESR VS. FREQUENCY Axis Title 100 10000 1. 22 μF - 6 V MM 2. 47 μF - 6 V M0 3. 100 μF - 6 V A0 4.
PAGE 5
T58 www.vishay.
PAGE 6
Polymer Guide www.vishay.com Vishay Guide for Tantalum Solid Electrolyte Chip Capacitors with Polymer Cathode INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability, and long service life are primary considerations.
PAGE 7
Polymer Guide www.vishay.com Vishay SOLID ELECTROLYTE POLYMER TANTALUM CAPACITORS Solid electrolyte polymer capacitors utilize sintered tantalum pellets as anodes. Tantalum pentoxide dielectric layer is formed on the entire surface of anode, which is further impregnated with highly conductive polymer as cathode system.
PAGE 8
Polymer Guide www.vishay.
PAGE 9
Polymer Guide www.vishay.com Vishay POLYMER CAPACITORS - MOLDED CASE SERIES T55 PRODUCT IMAGE VPolyTanTM, molded case, high performance polymer High performance -55 °C to +105 °C 3.3 μF to 1000 μF 2.5 V to 63 V ± 20 % 0.
PAGE 10
Polymer Guide www.vishay.com Vishay MOLDED CAPACITORS, T55 TYPE PLASTIC TAPE AND REEL PACKAGING DIMENSIONS in millimeters E A B C Label D W TAPE WIDTH A+0/-3 B+1/0 C ± 0.2 D ± 0.5 E ± 0.5 W ± 0.3 8 12 Ø 180 Ø 60 Ø 13 Ø 21 2.0 9.0 13.0 Note • A reel diameter of 330 mm is also applicable PLASTIC TAPE SIZE DIMENSIONS in millimeters Pocket Perforation E Ø 1.5 + 0.10 W B F A P1 t Direction of tape flow 4.0 ± 0.1 2.0 ± 0.
PAGE 11
Polymer Guide www.vishay.com Vishay LEADFRAMELESS MOLDED CAPACITORS, ALL TYPES PLASTIC TAPE AND REEL PACKAGING in inches [millimeters] 0.157 ± 0.004 [4.0 ± 0.10] Tape thickness Deformation between embossments 0.014 [0.35] max. 0.059 + 0.004 - 0.0 [1.5 + 0.10 - 0.0] Top cover tape B1 (max.) (6) 10 pitches cumulative tolerance on tape ± 0.008 [0.200] Embossment 0.079 ± 0.002 0.069 ± 0.004 [2.0 ± 0.05] [1.75 ± 0.10] A0 K0 0.030 [0.75] min. (3) B0 0.030 [0.75] min.
PAGE 12
Polymer Guide www.vishay.com Vishay CARRIER TAPE DIMENSIONS in inches [millimeters] CASE CODE TAPE SIZE B1 (MAX.) (1) D1 (MIN.) F K0 (MAX.) P1 W 0.071 [1.8] 0.315 ± 0.004 [8.0 ± 0.10] 0.476 ± 0.008 [12.1 ± 0.20] E5 12 mm 0.329 [8.35] 0.059 [1.5] 0.217 ± 0.002 [5.50 ± 0.05] MM (2) 8 mm 0.075 [1.91] 0.02 [0.5] 0.138 [3.5] 0.043 [1.10] 0.157 [4.0] 0.315 [8.0] M1 12 mm 0.32 [8.2] 0.059 [1.5] 0.217 ± 0.002 [5.5 ± 0.05] 0.094 [2.39] 0.315 ± 0.04 [8.0 ± 1.0] 0.472 + 0.012 / - 0.
PAGE 13
Polymer Guide www.vishay.com Vishay PACKING AND STORAGE Polymer capacitors meet moisture sensitivity level rating (MSL) of 3 or 4 as specified in IPC/JEDEC® J-STD-020 and are dry packaged in moisture barrier bags (MBB) per J-STD-033. MSL for each particular family is defined in the datasheet - either in “Features” section or “Standard Ratings” table. Level 3 specifies a floor life (out of bag) of 168 hours and level 4 specifies a floor life of 72 hours at 30 °C maximum and 60 % relative humidity (RH).
PAGE 14
Polymer Guide www.vishay.com Vishay MOLDED CAPACITORS, T55 TYPE PAD DIMENSIONS in millimeters L X Capacitor Pattern Y W G Z CAPACITOR SIZE PAD DIMENSIONS CASE / DIMENSIONS L W G (max.) Z (min.) X (min.) Y (Ref.) J 1.6 0.8 0.7 2.5 1.0 0.9 P 2.0 1.25 0.5 2.6 1.2 1.05 A 3.2 1.6 1.1 3.8 1.5 1.35 T/B 3.5 2.8 1.4 4.1 2.7 1.35 Z/V/D 7.3 4.3 4.1 8.2 2.9 2.
PAGE 15
Polymer Guide www.vishay.com Vishay GUIDE TO APPLICATION 1. AC Ripple Current: the maximum allowable ripple current shall be determined from the formula: I R MS = 4. Reverse Voltage: the capacitors are not intended for use with reverse voltage applied. However, they are capable of withstanding momentary reverse voltage peaks, which must not exceed the following values: At 25 °C: 10 % of the rated voltage or 1 V, whichever is smaller. At 85 °C: 5 % of the rated voltage or 0.5 V, whichever is smaller.
PAGE 16
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.