Datasheet

ManualsBrandsVishay ManualsCapacitorsMolded Case Low Profile Tantalum Capacitor 220nF ±10% 35V

TMCU

www.vishay.com

Vishay Polytech

Revision: 26-Oct-17

Document Number: 40180

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Solid Tantalum Surface Mount Chip Capacitors,

Molded Case, Ultra Flat Low Profile

PERFORMANCE / ELECTRICAL

CHARACTERISTICS

Operating Temperature: -55 °C to +125 °C

(above 85 °C, voltage derating is required)

Capacitance Range: 0.1 μF to 220 μF

Capacitance Tolerance: ± 10 %, ± 20 %

Voltage Rating: 2.5 V

to 35 V

FEATURES

• Small size, low profile

• Terminations:

Case UA: 100 % matte tin

Case UB: Ni / Pd / Au

• Qualified to EIA-717

• MSL level: 1 (UA case size), 3 (UB case size)

• Compatible with “high volume” automatic pick

and place equipment

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

APPLICATIONS

• Industrial

• General purpose

Available

ORDERING INFORMATION

TMCU A 1G 107 M TR (2) F

TYPE CASE

CODE

DC VOLTAGE

RATING AT +85 °C

CAPACITANCE

(μF)

CAPACITANCE

TOLERANCE

PACKAGING

POLARITY

(OPTIONAL) TERMINAL

CODE

See

Ratings

and

Case

Codes

table.

0E = 2.5 V

0G = 4 V

0J = 6.3 V (7 V)

1A = 10 V

1C = 16 V

1D = 20 V

1E = 25 V

1V = 35 V

This is

expressed in

picofarads. The

first two digits

are the

significant

figures. The

third is the

number of

zeros to follow.

K = ± 10 %

M = ± 20 %

TR = 7" reel,

cathodes close

to perforation

side

Halogen-free

(special order)

F = lead

(Pb)-free

terminations

DIMENSIONS in inches [millimeters]

CASE CODE EIA SIZE L W H l a

UA 3216-12

0.126 ± 0.008

[3.2 ± 0.2]

0.063 ± 0.008

[1.6 ± 0.2]

0.047 max.

[1.2 max.]

0.030 ± 0.012

[0.8 ± 0.3]

0.047 ± 0.008

[1.2 ± 0.2]

UB 3528-12

0.138 ± 0.008

[3.5 ± 0.2]

0.110 ± 0.008

[2.8 ± 0.2]

0.047 max.

[1.2 max.]

0.030 ± 0.012

[0.8 ± 0.3]

0.071 ± 0.008

[1.8 ± 0.2]

Anode indication belt mark

UA, UB case

Summary of content (14 pages)

PAGE 1
TMCU www.vishay.com Vishay Polytech Solid Tantalum Surface Mount Chip Capacitors, Molded Case, Ultra Flat Low Profile FEATURES • Small size, low profile • Terminations: Case UA: 100 % matte tin Case UB: Ni / Pd / Au • Qualified to EIA-717 Available • MSL level: 1 (UA case size), 3 (UB case size) • Compatible with “high volume” automatic pick and place equipment PERFORMANCE / ELECTRICAL CHARACTERISTICS Available • Material categorization: for definitions of compliance please see www.vishay.
PAGE 2
TMCU www.vishay.com Vishay Polytech RATINGS AND CASE CODES μF 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 2.5 V 4V UA UA UA / UB UA / UB UB UB UB UB 6.
PAGE 3
TMCU www.vishay.
PAGE 4
TMCU www.vishay.com Vishay Polytech STANDARD RATINGS CAPACITANCE (μF) CASE CODE PART NUMBER MAX. DCL AT +25 °C (μA) MAX. DF AT +25 °C, 120 Hz (%) MAX. ESR AT +25 °C, 100 kHz () MAX. RIPPLE, 100 kHz IRMS (A) 0.140 10 VDC AT +85 °C; 6.3 VDC AT +125 °C 4.7 UA TMCUA1A475(1)TRF 0.5 6 4.0 6.8 UA TMCUA1A685(1)TRF 0.7 6 4.0 0.140 10 UA TMCUA1A106(1)TRF 1.0 8 4.0 0.140 0.164 15 UA TMCUA1A156(1)TRF 3.0 12 2.9 15 UB TMCUB1A156(1)TRF 1.5 10 2.8 0.185 22 UA TMCUA1A226MTRF 4.
PAGE 5
TMCU www.vishay.com Vishay Polytech STANDARD RATINGS CAPACITANCE (μF) CASE CODE PART NUMBER MAX. DCL AT +25 °C (μA) MAX. DF AT +25 °C, 120 Hz (%) MAX. ESR AT +25 °C, 100 kHz () MAX. RIPPLE, 100 kHz IRMS (A) 35 VDC AT +85 °C; 22 VDC AT +125 °C 0.10 UA TMCUA1V104(1)TRF 0.5 4 40.0 0.044 0.15 UA TMCUA1V154(1)TRF 0.5 4 40.0 0.044 0.22 UA TMCUA1V224(1)TRF 0.5 4 40.0 0.044 1.0 UA TMCUA1V105MTRF 0.5 8 16.5 0.069 1.0 UB TMCUB1V105(1)TRF 0.5 6 8.8 0.104 1.
PAGE 6
TMCU www.vishay.com Vishay Polytech PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Specified initial value Capacitance change Temperature characteristics Measure the specified characteristics in each stage Dissipation factor (%), maximum Leakage current Solder heat resistance Solder Dip 260 °C ± 5 °C, 10 s ± 1 s Reflow 260 °C, 10 s ± 1 s Moisture resistance no load Leave at 40 °C and 90 % to 95 % RH for 500 h High temperature load 85 °C.
PAGE 7
Molded Guide www.vishay.com Vishay Polytech Guide for Tantalum and Niobium Solid Electrolyte Chip Capacitors INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability, and long service life are primary considerations.
PAGE 8
Molded Guide www.vishay.com Vishay Polytech SOLID ELECTROLYTE TANTALUM CAPACITORS TANTALUM CAPACITORS FOR ALL DESIGN CONSIDERATIONS Solid electrolyte capacitors contain manganese dioxide, which is formed on the tantalum pentoxide dielectric layer by impregnating the pellet with a solution of manganous nitrate. The pellet is then heated in an oven, and the manganous nitrate is converted to manganese dioxide.
PAGE 9
Molded Guide www.vishay.
PAGE 10
Molded Guide www.vishay.com Vishay Polytech SOLID TANTALUM CAPACITORS - MOLDED CASE SERIES TMCTX TMCH THC PRODUCT IMAGE TYPE FEATURES Solid tantalum surface mount chip capacitors, molded case Built-in fuse TEMPERATURE RANGE CAPACITANCE RANGE VOLTAGE RANGE High reliability -55 °C to +125 °C DISSIPATION FACTOR CASE SIZES -55 °C to +150 °C 1.0 μF to 68 μF 0.1 μF to 100 μF 0.
PAGE 11
Molded Guide www.vishay.com Vishay Polytech PLASTIC TAPE AND REEL PACKAGING DIMENSIONS in millimeters E A B C Label D W CASE CODE TAPE WIDTH A+0/-3 B+1/0 C ± 0.2 D ± 0.5 E ± 0.5 W ± 0.3 J, P, A, UA, B, UB 8 C, E, F 12 Ø 180 Ø 60 Ø 13 Ø 21 2.0 9.0 13.0 TAPE SIZE in millimeters Pocket Perforation E Ø 1.5 + 0.10 F B W A P1 t Direction of tape flow 4.0 ± 0.1 2.0 ± 0.
PAGE 12
Molded Guide www.vishay.com Vishay Polytech RECOMMENDED REFLOW PROFILES Capacitors should withstand reflow profile as per J-STD-020 standard TEMPERATURE (°C) Tp tp Max. ramp-up rate = 3 °C/s Max. ramp-down rate = 6 °C/s TL Ts max. TC - 5 °C tL Preheat area Ts min. ts 25 Time 25 °C to peak TIME (s) PROFILE FEATURE Preheat / soak Temperature min. (Ts min.) Temperature max. (Ts max.) Time (ts) from (Ts min. to Ts max.
PAGE 13
Molded Guide www.vishay.com Vishay Polytech GUIDE TO APPLICATION 1. AC Ripple Current: the maximum allowable ripple current shall be determined from the formula: I R MS = 4. P -----------R ESR where, P= 2. At 85 °C: 5 % of the rated voltage or 0.5 V, whichever is smaller. power dissipation in W at +25 °C as given in the tables in the product datasheets. RESR = the capacitor equivalent series resistance at the specified frequency. 5. Mounting Precautions: 5.
PAGE 14
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.