Datasheet

ManualsBrandsVISHAY ManualsIR ComponentsIR receiver Non-standard Axial lead 33 kHz 950 nm TSOP 1833

TSOP22.., TSOP24.., TSOP48.., TSOP44..

www.vishay.com

Vishay Semiconductors

Rev. 1.3, 05-Feb-14

Document Number: 82459

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

IR Receiver Modules for Remote Control Systems

MECHNICAL DATA

Pinning for TSOP44.., TSOP48..:

1 = OUT, 2 = GND, 3 = V

Pinning for TSOP22.., TSOP24..:

1 = OUT, 2 = V

, 3 = GND

FEATURES

• Low supply current

• Photo detector and preamplifier in one package

• Internal filter for PCM frequency

• Improved shielding against EMI

• Supply voltage: 2.5 V to 5.5 V

• Improved immunity against ambient light

• Insensitive to supply voltage ripple and noise

• Material categorization:

For definitions of compliance please see

www.vishay.com/doc?99912

DESCRIPTION

The TSOP22.., TSOP48.., TSOP24.. and TSOP44.. series

are miniaturized IR receiver modules for infrared remote

control systems. A PIN diode and a preamplifier are

assembled on lead frame, the epoxy package contains an IR

filter.

The demodulated output signal can be directly connected to

a microprocessor for decoding.

The TSOP24.., TSOP44.. are optimized to suppress almost

all spurious pulses from energy saving lamps like CFLs. The

AGC4 used in the TSOP24.. and TSOP44.. may suppress

some data signals. The TSOP22.., TSOP48.. are legacy

products for all common IR remote control data formats.

Between these four receiver types, the TSOP24.., TSOP44..

are preferred. Customers should initially try the TSOP24..,

TSOP44 in their design.

These components have not been qualified according to

automotive specifications.

Note

(1)

We advise try AGC4 first if the burst length is unknown.

16672

PARTS TABLE

AGC

LEGACY, FOR

LONG BURST REMOTE CONTROLS (AGC2)

RECOMMENDED FOR

LONG BURST CODES (AGC4)

(1)

Carrier

frequency

30 kHz TSOP4830 TSOP2230 TSOP4430 TSOP2430

33 kHz TSOP4833 TSOP2233 TSOP4433 TSOP2433

36 kHz TSOP4836 TSOP2236 TSOP4436

(2)(3)(4)

TSOP2436

(2)(3)(4)

38 kHz TSOP4838 TSOP2238 TSOP4438

(5)(6)(7)

TSOP2438

(5)(6)(7)

40 kHz TSOP4840 TSOP2240 TSOP4440 TSOP2440

56 kHz TSOP4856 TSOP2256 TSOP4456

(7)(8)

TSOP2456

(7)(8)

Package Mold

Pinning 1 = OUT, 2 = GND, 3 = V

1 = OUT, 2 = V

, 3 = GND 1 = OUT, 2 = GND, 3 = V

1 = OUT, 2 = V

, 3 = GND

Dimensions (mm) 6.0 W x 6.95 H x 5.6 D

Mounting Leaded

Application Remote control

Best remote control code

(2)

RC-5

(3)

RC-6

(4)

Panasonic

(5)

NEC

(6)

Sharp

(7)

r-step

(8)

Thomson RCA

Summary of content (7 pages)

PAGE 1
TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Improved shielding against EMI • Supply voltage: 2.5 V to 5.5 V 1 • Improved immunity against ambient light 2 • Insensitive to supply voltage ripple and noise 3 16672 • Material categorization: For definitions of compliance please see www.vishay.
PAGE 2
TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170-10 16833_14 Transmitter with TSALxxxx 3 VS 1 Input Band pass AGC µC OUT Demodulator VO GND GND The external components R1 and C1 are optional to improve the robustness against electrical overstress (typical values are R1 = 100 Ω, C1 = 0.1 µF).
PAGE 3
TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal ton, toff - Output Pulse Width (ms) Ee (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * T 10/f0 is recommended for optimal function * tpi VO Output Signal 1) 2) VOH 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f 0 VOL 0.8 ton 0.7 0.6 0.5 toff 0.4 0.3 0.2 λ = 950 nm, optical test signal, Fig. 1 0.1 0 0.
PAGE 4
TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors S (λ) rel - Relative Spectral Sensitivity Ee min. - Threshold Irradiance (mW/m2) 1.0 0.9 0.8 0.7 f = f0 f = 10 kHz f = 100 kHz 0.6 0.5 0.4 0.3 0.2 0.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 750 0 1 10 100 1000 ΔVS RMS - AC Voltage on DC Supply Voltage (mV) 800 850 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 900 950 1000 1050 1100 1150 λ- Wavelength (nm) 21425 Fig.
PAGE 5
TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below.
PAGE 6
TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 3.9 1 1 30.5 ± 0.5 (5.55) 8.25 6.95 5.3 6 0.85 max. 0.89 0.5 max. 2.54 nom. 1.3 0.7 max. 4.1 2.54 nom. 5.6 marking area Not indicated tolerances ± 0.2 technical drawings according to DIN specifications R 2.5 Drawing-No.: 6.550-5169.01-4 Issue: 9; 03.11.10 13655 Rev. 1.3, 05-Feb-14 6 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
PAGE 7
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.