TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Improved immunity against HF and RF noise • Low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency 1 2 3 • Supply voltage: 2.5 V to 5.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 3 17170-11 Transmitter with TSALxxxx 4 Input Demo dulator Band pass AGC R1 IR receiver VS OUT μC OUT 1 PIN + VS C1 Circuit 33 kΩ VS VO GND GND GND Control circuit R1 and C1 recommended to reduce supply ripple for VS < 2.8 V 16839-1 ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage TEST CONDITION VS -0.3 to +6 V Supply current IS 5 mA Output voltage VO -0.3 to (VS + 0.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) ton, toff - Output Pulse Width (ms) Optical Test Signal Ee (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * T 10/f0 is recommended for optimal function * tpi Output Signal VO 1) VOH 2) 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f0 0.8 ton 0.7 0.6 0.5 toff 0.4 0.3 0.2 λ = 950 nm, optical test signal, fig. 1 0.1 0 0.
TSOP62.., TSOP64.. Vishay Semiconductors 1.0 S (λ) rel - Relative Spectral Sensitivity Ee min. - Threshold Irradiance (mW/m2) www.vishay.com f = f0 0.9 0.8 0.7 f = 30 kHz 0.6 0.5 f = 20 kHz 0.4 f = 10 kHz 0.3 0.2 0.1 f = 100 Hz 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 1 10 100 0 750 1000 ΔVsRMS - AC Voltage on DC Supply Voltage (mV) 800 850 950 1000 1050 1100 1150 λ- Wavelength (nm) 21425 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 900 Fig.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 7.5 Pick and place area. TT taping 7.2 (1.5) 2.8 2.2 5.3 A 1 4 0.5 ± 0.15 0.1 (1.4) 0.3 4x 0.1 1.27 2.9 3 x 1.27 = 3.81 4 0.4 A 5.51 Not indicated tolerances ± 0.3 Pick and place area. TR taping technical drawings according to DIN specifications 2.6 Footprint 2.35 3 x 1.27 = 3.81 0.9 2.2 1.27 R 1.7 Drawing-No.: 6.544-5341.01-4 Issue: 8; 02.09.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE Axis Title 300 10000 max. 260 °C 255 °C 240 °C 2nd line Temperature (°C) 250 245 °C 217 °C 1000 200 max. 20 s 150 max. 120 s max. 100 s 100 100 Max. ramp up 3 °C/s 50 Max. ramp down 6 °C/s Max. 2 cycles allowed 10 0 0 19800 50 100 150 200 250 300 Time (s) TAPING VERSION TSOP..TT DIMENSIONS in millimeters 16584 Rev. 1.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR DIMENSIONS in millimeters 16585 Rev. 1.6, 03-Apr-18 8 Document Number: 82463 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area.
TSOP62.., TSOP64.. www.vishay.
TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors ESD PRECAUTION VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. The Vishay Semiconductors standard bar code labels are printed at final packing areas.
SMD Tape and Reel www.vishay.com Vishay Semiconductors Tape and Reel Standards for Surface-Mount IR Receiver Modules NUMBER OF COMPONENTS Vishay Semiconductor surface-mount IR receivers are packaged on tape and reel. The following specification is based on IEC publication 286, which takes the industrial requirements for automatic insertion into account. A.
SMD Tape and Reel www.vishay.com Vishay Semiconductors REEL DIMENSIONS FOR PANHEAD, HEIMDALL, AND TVCASTSMD TR in millimeters 16734 Note • The body structure of the reel can vary Rev. 2.5, 08-Mar-18 2 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters A. Panhead (TSOP36...TT, TSSP....TT, TSOP6...TT, TSOP16...TT, TSOP96...TT) 16584 Rev. 2.5, 08-Mar-18 3 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters 3.65 0.3 B. Heimdall (TSOP75...TT, TSOP77...TT, TSSP77...TT, TSOP15...TT, TSOP95...TT) 16 1.75 7.5 Ø 1.5 4 8 Direction of feed 2 Ø 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5338.01-4 Issue: 4; 12.06.13 Rev. 2.5, 08-Mar-18 4 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters 3 0.3 C. Heimdall without lens (TSOP75...WTT, TSOP77...WTT, TSSP77...WTT, TSOP15...WTT, TSOP95...WTT) 16 1.75 7.5 Ø 1.5 4 Direction of feed 8 2 Ø 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5341.01-4 Issue: 3; 06.10.15 Rev. 2.5, 08-Mar-18 5 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT1 (TOP VIEW) DIMENSIONS in millimeters D. Belobog (TSOP37...TT1, TSOP57...TT1, TSOP17...TT1, TSOP97...TT1) Tape and reel dimensions: Ø 60 min. Unreel direction Reel size “Y” TT1 Ø 180 ± 2 = 1800 pcs. Tape position coming out from reel 2± ØY 0 .5 Ø 21 ± 0.8 Ø 13 ± 0.2 Label posted here (12.4) 18.4 max. Parts mounted Empty leader 400 mm min. 100 mm min. with cover tape Leader and trailer tape: Empty trailer 200 mm min.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT1 (TOP VIEW) DIMENSIONS in millimeters E. Belobog with shield (TSOP37...HTT1, TSOP57...HTT1, TSOP17...HTT1, TSOP97...HTT1) Tape and reel dimensions: Reel size “Y” TT1 Ø 180 ± 2 = 1500 pcs. X 2± Ø 60 min. Unreel direction Tape position coming out from reel ØY 0.5 Ø 21 ± 0.8 Ø 13 ± 0.2 Label posted here (12.4) 18.4 max. Parts mounted Empty leader 400 mm min. 100 mm min.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..DF1P (SIDE VIEW) DIMENSIONS in millimeters F. Minimold DF1P (TSOP33...DF1P, TSOP53...DF1P, TSOP13...DF1P, TSOP93...DF1P) +3 -0 Technical drawing according to DIN specifications Form of the leave open of the wheel is supplier specific. Dimensions according to IEC EN 60 286-3 Ø 12 .8 m 1.5 in. mi n. Ø 60 min. Ø 330 +0 -4 24.4 Tape width: 24 20 .2 Reel hub 2:1 n. (2) (1.55) B (0.4) (12) (1.5 min.) A A (11.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters G. TVCastSMD TR1 (TSOP59...TR1, TSOP39...TR1, TSOP19...TR1, TSOP99...TR1) (1.7) (9.75) (2.85) A-A (2 : 1) (16) (7.5) B-B (2 : 1) (1.75) (7.05) B B A (2) (Ø 1) Direction of feed (4) (12) A Ø 1.5 Technical drawings according to DIN specification. Drawing-No.: GO-100220.10_Z Issue B: 08.02.17 Rev. 2.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters A. Panhead (TSOP36...TR, TSSP6...TR, TSOP6...TR, TSOP16...TR, TSOP96...TR) 16585 Rev. 2.5, 08-Mar-18 10 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters 0.3 3.6 B. Heimdall (TSSP7...., TSOP75...TR, TSOP77...TR, TSSP7....TR, TSOP15...TR, TSOP95...TR) 16 7.5 1.75 1.34 ref. Ø 1.5 4 Direction of feed 8 2 Ø 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5337.01-4 Issue: 2; 06.10.15 Rev. 2.5, 08-Mar-18 11 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters 3.6 0.3 C. Heimdall without lens (TSOP75...WTR, TSOP77...WTR, TSSP...WTR, TSOP15...WTR, TSOP95...WTR) 16 1.75 7.5 Ø 1.5 4 Direction of feed 8 2 Ø 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5342.01-4 Issue: 2; 12.06.13 Rev. 2.5, 08-Mar-18 12 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
SMD Tape and Reel www.vishay.com Vishay Semiconductors LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE REEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area.
SMD Tape and Reel www.vishay.com Vishay Semiconductors DRY PACKAGING The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. LEVEL CAUTION This bag contains MOISTURE-SENSITIVE DEVICES Aluminum bag 4 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a.
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.