User's Manual

ManualsBrandsVision Automobile Electronics Industrial ManualsElectronics4-in-1 Motion Sensor / Wireless PIR Motion Sensor

Federal Communications Commission Statement

This equipment has been followed to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try and

correct the interferene by one of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver,

- Connect the equipment into and outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undersired

operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

Limited Warranty

Vision Guarantees that every wireless PIR sensor is free from physical defects in material

and workmanship under normal use for one year from the date of purchase. If the product

proves defective during this one-year warrany period, Vision will replace it free of charge.

Vision does not issue any refunds. This warnnty is extended to the original end user

purchase only and is not transferable. This warranty does not apply to : (1) damage to units

caused by accident, dropping or abuse in handling, or any negligent use; (2) units which

have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not

used in accordance with instruction; (4) damanges exceeding the cost of the produt; (5)

transit damage, initial installation costs, removal cost, or reinstallation cost.

For information on addional devices, plesae visit us at www.visionsecurity.com.tw

Installation & Operation Manual

ZP3112IN-5

ZP3112MY-5

ZP3112EU-5

ZP3112RU-5

ZP3112US-5

ZP3112IL-5

ZP3112KR-5

ZP3112HK-5

ZP3112BR-5

ZP3112JP-5

Wireless PIR Motion Sensor

ZP 3112-5 V0 1050113

Summary of content (4 pages)

PAGE 1
Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
PAGE 2
Introduction Thanks for choosing the Vision’s wireless Motion sensor of the home security device. This TM enabled device (interoperable, two-way RF mesh networking sensor is a Z-Wave technology) and is fully compatible with any Z-Wave TM enabled network and it’s security TM enabled device acts as a signal repeater and framework. Every mains powered Z-Wave multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”.
PAGE 3
“association”, and following its instruction to associate the ZP3112 with other device. Support grouping identifier=1. Support one association group (5 nodes). “Association” is used for other grouping devices chain reaction. Red LED will flash once when trigger.
PAGE 4
configuration setting, refer Table 1 (Parameter 1) will send Basic Set OFF (0x00), Red LED will flash once, and refer to table for status. 4. The ZP3112 sensor equipped with tamper switch. If the tamper switch is triggered (or remove the cover), the ZP3112 sensor will send Alarm Report, LED will flash once and refer to table for status. 5. If the tamper switch is closed (or closed the cover), ZP3112 will send Alarm Report, and refer to table for status.