User's Manual

ManualsBrandsVision Automobile Electronics Industrial ManualsElectronics4-in-1 Motion Sensor

Federal Communications Commission Statement

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operation.

FCC Caution

To assure continued compliance, any changes or modifications not expressly approved by

the party responsible for compliance

may void the user’s authority to operate his equipment. (Example – use only shielded

interface cables when connecting to computer or peripheral devices)

FCC Statement in User’s Manual (for class B) FCC Section 15.105 “Federal Communications

Commission (FCC) Statement”

This equipment has been tested and found to comply with the limits for a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Limited Warranty

Vision Guarantees that every wireless PIR sensor is free from physical defects in material and

workmanship under normal use for one year from the date of purchase. If the product proves

defective during this one-year warranty period, Vision will replace it free of charge. Vision does

not issue any refunds. This warranty is extended to the original end user purchase only and is

not transferable. This warranty does not apply to : (1) damage to units caused by accident,

dropping or abuse in handling, or any negligent use; (2) units which have been subject to

unauthorized repair, taken apart, or otherwise modified; (3) units not used in accordance with

instruction; (4) damages exceeding the cost of the product; (5) transit damage, initial

installation costs, removal cost, or reinstallation cost. For information on additional devices,

please visit us at www.visionsecurity.com.tw

ZP3113-7 V0 1090803

Installation & Operation Manual

ZP3113IN-7

ZP3113EU-7

ZP3113RU-7

ZP3113US-7

ZP3113BR-7

ZP3113IL-7

ZP3113HK-7

ZP3113TH-7

ZP3113KR-7

ZP3113JP-7

4-in-1 Motion Sensor

(Temp./Humidity/Light Sensor Built-In)

IMPORTANT NOTE :

FCC Radiation Exposure Statement :

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

Summary of content (5 pages)

PAGE 1
Federal Communications Commission Statement FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
Introduction Thanks for choosing the Vision’s wireless 4-in-1 Motion sensor of the home security device. The new multi-sensor consists of motion, temperature, humidity & light sensor for combing several functionality in one device; more attractive and economic consideration. This sensor is a Z-Wave TM enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave TM enabled network and it’s security framework.
PAGE 3
Configuration – Temperature Z-Wave Command Classes: COMMAND_CLASS_APPLICATION_STATUS COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_BATTERY COMMAND_CLASS_CONFIGURATION_V4 COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5 COMMAND_CLASS_INDICATOR_V3 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 Size Parameter 1 1 Parameter 2 1 COMMAND_CLASS_SECURITY_V2 COMMAND_CLASS_SENSOR_MULTILEVEL_V11 COMMAND_CLASS_SUPERVISION COMMAND_CLASS_TRANSPORT_SERVICE_V2 COMMAND_
PAGE 4
Configuration – Acknowledge: Size Parameter 8 Value 0 ~ 10 (unsigned decimal) Times (default: 3 Times) 1 8. Battery Capacity Detection: * Use “Battery Get” command to have the battery capacity back in % * It will detect the battery capacity automatically * Low Battery Auto Report when power is lower than 2.4V +/- 0.1V Humidity Report: Use SENSOR_MULTILEVEL_GET for getting the Humidity Report.
PAGE 5
Operation 9. 1. Using adhesive tape to mount ZP3113 at 2 meters above surface. To enhance proper operation, place ZP3113 on the location which can detect the room widely. The PIR needs one minute to be stable after initial power on, please proceed motion detection after that. Support SECURITY S0, SECURITY S2 UNAUTHENTICATED & SECURITY S2 AUTHENTICATED. 10. Support SmartStart, please scan the QR Code from ZP3113 for SmartStart.