User's Manual

ManualsBrandsVision Automobile Electronics Industrial ManualsElectronicsWireless CO Detector

Federal Communications Commission Statement

This equipment has been followed to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

and correct the interferene by one of the following measures:

-- Reorient or relocate the receiving antenna,

-- Increase the separation between the equipment and receiver,

-- Connect the equipment into and outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undersired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

Limited Warranty

Vision Guarantees that every wireless CO detector is free from physical defects in material and

workmanship under normal use for one year from the date of purchase. If the product proves

defective during this one-year warranty period, Vision will replace it free of charge. Vision does not

issue any refunds. This warranty is extended to the original end user purchase only and is not

transferable. This warranty does not apply to: (1) damage to units caused by accident, dropping or

abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair,

opened, taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4)

damages exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost,

or reinstallation cost.

For information on addional devices, plesae visit us at www.visionsecurity.com.tw

WARNING: The carbon monoxide sensing unit has only 5-year limited life. For the

security issue, we strongly recommend the user to change whole the CO detector after

4-year usage.

Installation & Operation Manual

ZS6301IN-5

ZS6301MY-5

ZS6301EU-5

ZS6301RU-5

ZS6301US-5

ZS6301IL-5

ZS6301KR-5

ZS6301HK-5

ZS6301JP-5

ZS6301BR-5

Wireless CO Detector

ZS 6301-5

1040529

-5-

Summary of content (3 pages)

PAGE 1
Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
PAGE 2
Introduction Thanks for choosing the Vision’s wireless CO detector of the home security device. This detector is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™ enabled network and it’s security framework. Every mains powered Z-Wave™ enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-sports”.
PAGE 3
5. Suggestion of the CO Detector Location: 5. 6. 7. 8. 9. 10. 11. 12. Operation 1. 2. 3. 4. 13. Power-on Mode: 1) Install the battery into the module 2) The detector will emit a beep in 0.5 second and the three LEDs will flash once quickly. 3) Close the bracket. The CO detector will alarm once remove the bracket. Stand-by Mode: The Green LED flashes once every 60 seconds. Alarm Mode (In the status when the sensor is triggered.