Specifications

UVW-100B
CAMCORDERS
64
Record Review Function
Plays back two seconds of the last scene
and stops at the end of the previous record-
ing. The tape rewind time can be extended
up to a maximum of ten seconds.
LCD Multiple Display
8-digit LCD display indicates time data,
warning indicators and video status.
Battery status and two-channel audio level
are shown in a bar graph meter, while the
remaining tape quantity is shown in record.
Anton/Bauer Integration
In addition to a selection of battery cases,
Anton Bauer Digital batteries can also be
used with the UVW-100B. With these bat-
teries, the amount of remaining battery
power is accurately displayed on the LCD
panel and through the viewfinder. The
Anton Bauer Ultralight System can also be
used. With this system, lighting power is
turned on and off according to the VTR
Start/Stop function.
Full Function Control
Eject, REW, Play, FF and Stop function but-
tons are located on the top of the camcorder
and are covered to prevent misoperation.
During Record mode, they are automatically
inhibited. Record mode is activated with
the trigger buttons on the front of the cam-
era or on the zoom lens grip. With
the optional RM-81 Remote Control,
record Start/Stop can also be controlled.
Back Space Editing
Back Space Editing smooths transitions
between scenes while recording. Use of the
Time Code Regeneration function with the
Record Review function enables the UVW-
100B to record continuous Time Code at
any scene transition point. If the power is
turned off while in the Record Pause mode,
it will automatically resume the Rec Pause
mode at the last editing point when repow-
ered. This ensures a smooth transition in
the editing point.
Warning Indicators
Warning indicators on RF, Servo, Humid,
Slack, Tape-before-End, Tape-End, Low
Battery and End-of-Battery are superimposed
and displayed on the viewfinder screen, as
well as on the LCD window. An audible
alarm is sent through the built-in ear speaker
to warn you, as well.
Light and Well Balanced
Weighs 6.9kg (15 lbs. 3 oz.) with
viewfinder, battery, cassette and lens. The
compact, lightweight design, attributable in
part to the small drum mechanism, makes
the UVW-100B ideal for one-person oper-
ation. It is well balanced, with a low center
of gravity. Shoulder pad is adjustable, so
that optimum balance is maintained when
using different lenses and battery systems.
Due to the low power consumption (20w),
one fully charged NP-1B battery provides
continuous operation for approximately 60
minutes.
SONY
UVW-100B SPECIFICATIONS
CAMERA HEAD
Image Device:
Three 1⁄2˝ IT Power HAD
CCD Sensors
Picture Element:
768 x 492 (H x V)
Built-In Filters:
3200k, 5600k + 1/6 ND,
5600k
Horizontal Resolution:
700 TV Lines
Minimum Illumination:
4 Lux with f/1.4 + 18 dB
Sensitivity:
f/11 at 2000 Lux
Gain Selection:
OFF: 0 dB
MID: 1-17 dB in 1 dB Steps
HIGH: 2-18 dB in
1 dB Steps
(MID < HIGH)
0-18 dB Variable (AGC)
Shutter Speeds:
OFF, 1/100, 1/250, 1/500,
1/1000, 1/2000 sec
Clear Scan Range:
59.9 Hz to 200.3 Hz
S/N Ratio: 60 dB
VTR SECTION
Time Code I/O (BNC):
IN: 0.5v to 5v p-p 10KΩ
OUT: 1.0v p-p, 75w
Audio Input:
Mic: -60 dB Balanced,
Line: +4 dB Balanced
VIDEO PERFORMANCE
Bandwidth:
Y: 30 Hz to 4.0 MHz
R-Y/B-Y: 30 Hz -1.5 MHz
S/N Ratio: > 49 dB
CONNECTORS
Playback Adapter:
20-pin (VA-300)
External VTR Connector:
26-pin
Camera Video Out:
BNC x 2
Camera Genlock In:
BNC x 1
Camera MIC In:
XLR x 1 with 48v OUT
Audio In:
XLR x 2 with 48v OUT
Selectable
Headphone Out:
Stereo Mini Jack x 1
Remote:
Stereo Mini Jack x 1
Lens:
12-pin 1/2˝ Bayonet
DC In:
XLR 4-pin
AUDIO
Frequency Response:
50 Hz to 12.5k Hz
S/N Ratio:
>70 dB
GENERAL
Power Requirements:
12v +5.0/-1.0v DC
Power Consumption:
20w without Viewfinder
Weight:
6.9kg (15 lbs. 3oz.)
See us in person at NAB, Infocomm, and Siggraph