View The TM CCTV Owners Manual & Set-up Instructions Made in the USA
TABLE of CONTENTS Important Information 3 Introduction 4 Unpacking 4 Set-up 5-12 Close Down 13-15 Operating Controls Diagram Description of Controls 16 16-17 Operating your View 18 Care and Maintenance 19 Warranty & Service Information 19 2
Important Information Thank you for choosing the VIEWT M portable video magnification system. The VIEW is a quality portable in-line system with a movable camera, distance, close-up and mirror image viewing capability. Should your VIEW require service, refer to the Warranty Information section in this manual. Caution: Do not remove the cover on the monitor or camera. There are no user serviceable parts inside. Any changes or modifications not expressly approved or performed by Vision Technology, Inc.
Introduction Although your new system is very simple to use, it is very important that you read the instructions in this guide very carefully. This step by step manual is arranged in the way we anticipate you will operate your new system. Should you require assistance with set-up or a service issue please contact our client care department Monday—Friday 8:30am 4:30 pm CST at 1-800-560-7226. Our service department is here to provide courteous and knowledgeable responses to your inquiries.
Checklist _____ VIEW Video Magnification System _____ Power Supply (yellow plug) _____ Packaging material _____ Owner’s Manual _____ Product Registration Card Optional Accessories purchased may include: _____ Lithium Battery _____ Charger for Battery (black plug) _____ Soft Sided Carrying Case Set-up Place the CCTV base on a sturdy work surface, such as a desk or table. Be sure there is enough room to work with your CCTV as you move the X-Y Table from side to side.
Opening the ViewTM. 1. Set the View on a flat surface. 2. Grasp the back of the table top with the paper stop raised edge and pull up and out. The table top is held in place with 2 locking clips shown below. 3. Lift up the tray.
View Folded Flat Unclip the table Lift up 7
Raise the table top to its fullest upright position as shown below. 4. Grasp the top of the monitor and lift up as shown below.
5. Reach in with one hand and pull the camera up 2-3 inches to release the components. 6. Raise the monitor & camera will rise.
7. Support the monitor up with one hand and turn the camera 180 degrees clockwise so the U-bar is angled away from the monitor. 8. Push up on the camera moving it towards the monitor with a gentle motion until the camera clicks into place.
9. Slide the tabletop out away from the base until there is room to fold it down. 10. Click into place by pressing down onto the clips.
Adjust monitor to desired height Turn camera 180 degrees back to x-y table viewing position, flip up for distance views 12
Closing the ViewTM. Turn off power and unplug. Lift and support the monitor in its highest position. 2. Slide the tabletop out away from the base. Unclip the top by pulling out on the back of the table. 3. Lift table top and slide the black portion back into the base. Clips are under here.
4. With the camera in the x-y viewing position support the monitor and pull back on the u-bar & camera to release it from the locked position. Slowly let it collapse into position. The camera will lower first.
5. Make sure the wires are tucked in between the two table clips. Fold down the monitor and table top. 6. Press firmly on the back of the table top to lock the table into position. Place in carry case for safety.
Operating Controls/Features On\Off: The Red ON\OFF switch is located on the left portion of the front control panel. To turn on monitor, press the on\off button on the front of the monitor. Select Mode: (Button to the right of the power button) 1. Full Color– is excellent for viewing photos 2. Black on White– makes any print high contrast black and any background high contrast white. 3.
Operating Controls/Features NTSC “Video Out” Port (located on the left rear side of the base) Connect a standard “NTSC” RCA cable to this port & video receiver (ie: LCD projector or TV screen) Quiet Mode An audible tone is sounded when you press a control button. To Change to Quiet Mode: with the system turned off, hold down the Mode button while turning the base unit on. Release after you hear two beeps. To turn the tone on again, repeat these same steps.
Operating your View The monitor on “The VIEWTM ” raises and lowers from table height up to 14 1/2” when locked into place. Distant Viewing The camera on “The VIEWT M” is movable. To change camera view, grasp camera and rotate it to view desired object. Mirror Image Viewing Press the Contrast button to make image a true mirror image. X-Y Table Place your reading material or other objects on the X-Y table & move the table from side to side or front to back to view the magnified form on the display.
Care & Maintenance The unit and display can be gently wiped with a clean soft cotton cloth to remove dust or dirt. Do not use any abrasive cleaners or spray it with cleaning solution. Do not store the VTI Video Magnifier at temperatures below 14 degrees F or above 122 degrees F. Make sure lid is snapped in place before lifting machine by the handle. You may also want to purchase a protective carrying case (part# VSC available from your Distributor).
Vision Technology Inc.