Specifications

ManualsBrandsVision ManualsExercise BikeE3200

E2200/E3200/E4200

C-0302/C-0303/C-0304

Installation Instructions

234 FISCHER AVENUE z COSTA MESA, CA 92626

(714) 424-6500

z (800) 840-0288 z (714) 424-6510 FAX

http://www.channelvision.com

z E-Mail: sales@channelvision.com

The Channel Vision Multi-Room Video E Series Modulator makes it easy to map any three

audio/video sources to any unused channels on you television set(s). Watching your security

cameras, laser disk, video tape, or any other video signal becomes as easy as switching channels

with your remote.

Because the E Series Modulator merges these additional inputs into your existing TV signal

"ahead of" your television sets the new channels will be available at every TV hooked up to

your coax cable.

You can even map your stereo system to an unused TV channel to pipe music to any room on

your TV "network!"

Summary of content (7 pages)

PAGE 1
E2200/E3200/E4200 C-0302/C-0303/C-0304 Installation Instructions The Channel Vision Multi-Room Video E Series Modulator makes it easy to map any three audio/video sources to any unused channels on you television set(s). Watching your security cameras, laser disk, video tape, or any other video signal becomes as easy as switching channels with your remote.
PAGE 2
Channel Vision ! CAUTION E2200, E3200, E4200 Tested To Comply With FCC Standards RISK OF ELECTRIC SHOCK DO NOT OPEN FOR HOME OR OFFICE USE CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. PROPER VENTILATION REQUIRED. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONAL. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 3
E3200 Basic Setup Reverse isolation is used to prevent the signal from your E Series from leaking out to the antenna or cable input. Reverse isolation is accomplished by placing an amplifier between your antenna or cable company input and the E Series combiner. This prevents the E Series signal from propagating back up the input line. Source A/V Inputs Cable or Antenna Another way to prevent leakage from your system is to cap all unused coax cable ports on you network with appropriate terminators.
PAGE 4
modulator will be assigned to and keep any potential interference out of the system. Model 3102, cleans up channel 80 and above. 7. Allow 1 to 2 channel spacing between modulated channels and "active" channels. 8. Always compensate for insertion loss with splitters and taps. There will always be a drop in antenna/cable signal strength when combining a modulator to an existing system (because of insertion loss with the combiner). 9.
PAGE 5
4. aimed at the sun or a reflection. Adjust camera lens - see lens manual. Ghosts on the Picture 1. Terminate all unused ports with 75Ω terminator model 2101. 2. Check for low quality combiner in system. Replace with high isolation combiner, HS model combiner. 3. Check the type of coax used in system. Inadequate shielding in coax will cause ghosting. Pull new coax (RG6 quad). O u c h!!! Modulated Picture is Too Dark 1.
PAGE 6
Splitter/Home Run Design 50' Tap System 32dB 9dB Cable or Antenna 28.5dB A/V Source Channel Vision RF Out 28.5dB MULTI ROOM VIDEO TECHNOLOGY CVT - 15PIA HS-2 E2200 25dB 18dB Basic design for home runs to close TVs. 18dB HS-4 50' 18dB 18dB 100' 6dB Attenuator 150' RF Out Large design application with minimal loss for the trunk line, tap pulls part of the signal and attenuates a portion (6dB, 9dB, 12dB, 17dB, 20dB). Cable or Antenna 11dB 27dB 10dB TV TV TV 26dB 22.
PAGE 7
Channel Vision Limited Warranty Channel Vision Technology will repair or replace any defect in material or workmanship which occur during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed.