TECHCONNECT HDBT OWNERS MANUAL www.visionaudiovisual.com/techconnect/tc2-hdbt 1 TC2-HDBT_manual_en.
DECLARATION OF CONFORMITY Where applicable Vision products are certified and comply with all known local regulations to a ‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all applicable certification standards for sale in the EU and other participating countries. The product described in this owner manual is in compliance with RoHS (EU directive 2002/95/EC), and WEEE (EU directive 2002/96/EC) standards.
USE ONLY DOMESTIC AC OUTLETS Connecting the unit to an outlet supplying a higher voltage may create a fire hazard. HANDLE THE POWER CORD WITH CARE Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself. Pulling the cord may damage it. If you do not intend to use your unit for any considerable length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and try to avoid dropping heavy objects on it. Do not tie a knot in the power cord.
TRANSMITTER 1 1. 2. 3. 4. 2 4 Mini USB-B connector - for firmware updates Link LED – shows HDMI input is connected HDMI Input RS-232 Input 5 5. 6. 7. 8. 3 6 7 8 CAT5e/6 Output Status LED – shows receiver is attached 12V 3A Power input Power LED 4 TC2-HDBT_manual_en.
RECEIVER 1 1. 2. 3. 4. 3 4 Mini USB-B connector - for firmware updates 3.5mm Minijack Audio Output (analogue) EDID selector HDMI Output 5 5. 6. 7. 8. 9. 2 6 7 8 9 RS-232 Output CAT5e/6 Input Status LED – shows transmitter is attached 12V 3A Power input Power LED 5 TC2-HDBT_manual_en.
INSTALLATION When used as a set connect power to either the transmitter or receiver but not both. Vision HDBT products use proprietary PoE. When using either the transmitter or receiver in conjunction with other manufacturer’s HDBT equipment it is necessary to connect power. 1. CONNECT CABLES You can use unshielded twisted pair (UTP) cable or shielded twisted pair (STP). For best results use STP CAT5e/6 cable. 2. POWER ON HDBT TRANSMITTER AND RECEIVER 3. POWER ON DISPLAY DEVICE 4.
TROUBLESHOOTING If your system is not operating properly, please refer to the following information. If the problem persists, disconnect from power and contact your AV reseller immediately. Problem Correction Status lights no on • • Check CAT5e/6 cable The cable should be wired to 568B standard at both ends. • If one end has green and orange swapped this is a crossover cable and cannot be used.
SPECIFICATIONS TRANSMITTER DIMENSIONS: 105 x 88 x 25 mm (length x width x height) RECEIVER DIMENSIONS: 108 x 106 x 25 mm PRODUCT WEIGHT: Set: 0.68 kg Transmitter: 0.30 kg Receiver: 0.38 kg CONSTRUCTION MATERIAL: Metal COLOUR: White TECHNICAL DETAILS: Signaling rates: 2.25Gbits x 3 Input Video Signal: 0.5-1.0 volts p-p Input DDC Signal: 5 volts p-p (TTL) Video(HDMI) format supported: DTV/HDTV:1080p/1080i/720p/576p/480p/576i/480i HDMI Version: 1.4 (3D) Output Audio: PCM 2.
WARRANTY This product comes with a 2-year return to base warranty, effective from the date of purchase. This warranty applies only to the original purchaser and is not transferable. For the avoidance of doubt, this will be taken from the information held by the appointed national distributor at the point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to notify the national distributor via your AV reseller.
