BENUTZERHANDBUCH OWNER’S MANUAL VX 3000 PRO ULTRA CLASS D MONO AMPLIFIER VERS. 1.
DEUTSCH SICHERHEITSHINWEISE DAS VON IHNEN ERWORBENE GERÄT IST NUR FÜR DEN BETRIEB AN EINEM 12-V-BORDNETZ EINES FAHRZEUGS AUSGELEGT. Andernfalls besteht Feuergefahr, die Gefahr eines elektrischen Schlages oder anderer Verletzungen. BITTE KEINE BEDIENUNG DES SOUNDSYSTEMS AUSFÜHREN, WELCHE VOM SICHEREN LENKEN DES FAHRZEUGS ABLENKEN KÖNNTE. Führen Sie keine Bedienungen aus, die Ihre Aufmerksamkeit längere Zeit in Anspruch nehmen.
DEUTSCH ENTSORGUNG Elektro- und Elektronikgeräte – Informationen für private Haushalte Das Elektro- und Elektronikgerätegesetz (ElektroG) enthält eine Vielzahl von Anforderungen an den Umgang mit Elektro- und Elektronikgeräten. Die wichtigsten Anforderungen sind hier zusammengestellt. 1. Getrennte Erfassung von Altgeräten Elektro- und Elektronikgeräte, die zu Abfall geworden sind, werden als Altgeräte bezeichnet.
DEUTSCH TECHNISCHE DATEN Modellbezeichnung VX 3000 PRO Kanäle 1 Schaltung Digital Ultra Class D AUSGANGSLEISTUNG RMS @ 14,4 V Watt @ 4 Ohm Watt @ 2 Ohm Watt @ 1 Ohm 1 x 1200 1 x 2200 1 x 3300 Lautsprecherimpedanz 1 - 8 Ohm Frequenzgang –3dB 10 - 5.000 Hz Dämpfungsfaktor > 7000 Signal-Rauschabstand 95 dB Klirrfaktor @ 1W/RMS < 0,07 % Filtersektion Subsonicfilter Tiefpassfilter Bassanhebung 10 - 100 Hz 50 - 5.
DEUTSCH BESTIMMUNGSGEMÄSSER GEBRAUCH Dieses Produkt ist nur für den Gebrauch in einem Fahrzeug mit 12 Volt Bordspannung und negativer Masse konzipiert und fungiert als Verstärker von Audiosignalen. Eine anderweitige Verwendung führt eventuell zu Beschädigungen am Produkt oder in der Umgebung des Produktes. MECHANISCHE INSTALLATION • Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B.
DEUTSCH ELEKTRISCHE ANSCHLÜSSE VOR DEM ANSCHLIESSEN Für den fachgerechten Anschluss des Soundsystems sind geeignete Kabelsets im Fachhandel erhältlich. Achten Sie beim Kauf auf einen ausreichenden Kabelquerschnitt und den passenden Sicherungswert der Kabel. Säubern und entfernen Sie vorhandene Rost- und Oxidationsstellen an allen Kontaktpunkten der Batterie und an den Massepunkten.
DEUTSCH 3 GND Verbinden Sie den Minuspol des Pufferkondensators mit einem geeigneten Massepunkt am Fahrzeugchassis. Verbinden Sie dann den Minuspol des Pufferkondensators mit dem Anschluss GND des Verstärkers. Das Massekabel sollte möglichst kurz sein und an einem blanken, metallischen Punkt des Fahrzeugchassis angebracht werden. Achten Sie darauf, dass dieser Punkt eine sichere elektrische Verbindung zum Minuspol der Fahrzeugbatterie hat.
DEUTSCH FUNKTIONSBESCHREIBUNG 7 8 9 10 11 12 13 INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.6 V 7 Am LINE INPUT befinden sich zwei Cinch-Eingänge, die jeweils mono angesteuert werden. Der Eingang LOW VOLTAGE ist für Niederpegelsignale von 0,4 bis 3,6 Volt geeignet. Am Eingang HIGH VOLTAGE können Sie ein Hochpegelsignal von 1,0 bis 9,0 Volt anschließen, wie es beispielsweise ein DSP liefert. ACHTUNG: Schließen Sie hier keinesfalls ein Hochpegelsignal von einem Lautsprecherausgang an.
DEUTSCH ANWENDUNGSBEISPIEL A INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.6 V Belegung Steuergerät Verstärker Cinch Ausgang Cinch Eingang SUB OUT LOW VOLTAGE 1Ω 100% Leistung ANWENDUNGSBEISPIEL B 2Ω 50% Leistung INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.6 V Belegung Steuergerät Verstärker Cinch Ausgang Cinch Eingang SUB OUT LOW VOLTAGE 2Ω 50% Leistung ANWENDUNGSBEISPIEL C INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.
DEUTSCH FEHLERBEHEBUNG ACHTUNG Sämtliche Hinweise dieser Fehlerbehebung beziehen sich auf das gesamte Soundsystem und deren Einzelkomponenten. Unter Umständen entspricht die Ausstattung Ihres Geräts nicht den in den Hinweisen beschriebenen Funktionen. Überspringen Sie dann diesen Punkt und machen mit dem nächsten weiter.
DEUTSCH DIE POWER LED LEUCHTET, ABER ES KOMMT KEIN TON AUS DEN LAUTSPRECHERN Überprüfen Sie folgende Schritte: Niederpegelmodus: Sind die RCA/Cinchkabel am Radio/Steuergerät und am Verstärker korrekt angeschlossen? • Die RCA/Cinchkabel sind korrekt angeschlossen. Es könnte ein RCA/Cinchkabel defekt sein. Überprüfen Sie die Funktion der RCA/Cinchkabel an einem anderen Audiogerät. Ersetzen Sie gegebenenfalls das defekte RCA/Cinchkabel.
DEUTSCH FEHLERBEHEBUNG VERZERRUNGEN ODER ZISCHGERÄUSCHE SIND AUS DEN LAUTSPRECHERN ZU HÖREN Überprüfen Sie folgende Schritte: Ist ein Eingangspegelregler am Verstärker zu hoch eingestellt? Drehen Sie den Regler langsam zurück, bis ein sauberes Audiosignal zu hören. Ist der Bass Boost (Bassanhebung) am Verstärker zu hoch eingestellt? Drehen Sie den Regler langsam zurück, bis ein sauberes Audiosignal zu hören.
DEUTSCH VERSTÄRKER AKTIVIERT DIE SCHUTZSCHALTUNG / DIE PROTECT LED LEUCHTET Überprüfen Sie folgende Schritte: Kurzschluss an den Lautsprecherkabeln • Klemmen Sie zunächst alle Lautsprecherkabel am Verstärker ab. Überprüfen Sie mit einem Multimeter die ohmsche Impedanz jedes Lautsprechers, indem sie zwischen dessen Plus- und Minusleitung messen. Bei handelsüblichen Lautsprechern schwankt der Wert zwischen 3 und 5 Ohm. Die Werte bei niederohmigen Subwoofern können geringer sein.
ENGLISH SAFETY INSTRUCTIONS THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE. Otherwise fire hazard, risk of injury and electric shock consists. PLEASE DO NOT MAKE ANY OPERATION OF THE SOUND SYSTEM, WHICH DISTRACT YOU FROM A SAFE DRIVING. Do not make any procedures, which demand a longer attention. Perform these operations not until you have stopped the vehicle on a safe place. Otherwise the risk of accident consists.
ENGLISH MOUNT THE DEVICE AND OTHER COMPONENTS OF THE SOUND SYSTEM SUFFICIENTLY. Otherwise the device and components may get loose and act as dangerous objects, which could cause serious harm and damages in the passenger room. ENSURE NOT TO DAMAGE COMPONENTS, WIRES AND CABLES OF THE VEHICLE WHEN YOU DRILL THE MOUNTING HOLES.
ENGLISH TECHNICAL SPECIFICATIONS Model VX 3000 PRO Channels 1 Circuit Digital Ultra Class D OUTPUT POWER RMS @ 14.4 V Watts @ 4 Ohms Watts @ 2 Ohms Watts @ 1 Ohms 1 x 1200 1 x 2200 1 x 3300 Loudspeaker Impedance 1 - 8 Ohm Frequency Range –3dB 10 - 5.000 Hz Damping Factor > 7000 Signal-to-Noise Ratio 95 dB THD+N < 0,07 % Filter Section Sub Sonic Filter Low Pass Filter Bass Boost 10 - 100 Hz 50 - 5.
ENGLISH INTENDED USE This product is only designed for use in a vehicle with 12 volt on-board voltage and negative ground and functions as an amplifier for audio signals. Any other use may lead to damage to the product or in the vicinity of the product. MECHANICAL INSTALLATION • Avoid any damages on the components of the vehicle like air bags, cables, board computer, seat belts, gas tank or the like. • Ensure that the chosen location provides a sufficient air circulation for the amplifier.
ENGLISH ELECTRICAL INTERCONNECTION BEFORE CONNECTING For the professional installation of a sound system, car audio retail stores offers appropriate wiring kits. Ensure a sufficient profile section and a suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
ENGLISH 3 GND Connect the minus pole of the power capacitor with a suitable contact ground point on the vehicle’s chassis. Then connect the minus pole of the power capacitor with the GND terminal of the amplifier. The ground wire must be as short as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable and safe electric connection to the negative “–”pole of the battery.
ENGLISH DESCRIPTION OF OPERATION 7 8 9 10 11 12 13 INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.6 V 7 There are two RCA inputs on the LINE INPUT, each of which is controlled in mono. The input LOW VOLTAGE is suitable for low level signals from 0.4 to 3.6 volts. At the input HIGH VOLTAGE you can connect a high level signal from 1.0 to 9.0 volts, such as that provided by a DSP. ATTENTION: Never connect a high-level signal from a loudspeaker output here. 8 The INPUT SENS.
ENGLISH APPLICATION EXAMPLE A INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.6 V Assignment Head Unit Amplifier RCA Output RCA Input SUB OUT LOW VOLTAGE 1Ω 100% Output Power APPLICATION EXAMPLE B 2Ω 50% Output Power INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.6 V Assignment Head Unit Amplifier RCA Output RCA Input SUB OUT LOW VOLTAGE 2Ω 50% Output Power APPLICATION EXAMPLE C INPUT SENS. HIGH VOLTAGE 1.0 - 9.0 V LOW VOLTAGE 0.4 - 3.
ENGLISH TROUBLE SHOOTING CAUTION All instructions in this trouble shooting refer to the entire sound system and its individual components. The features of your device may not match the functions described in the notes. Then skip this point and move on to the next one. NO FUNCTION / THE POWER LED IS NOT ILLUMINATED First check the fuse of the routed power cable on the vehicle battery The fuse is defective Replace the defective fuse with an equivalent one, never with a higher value. • The fuse fails again.
ENGLISH THE POWER LED IS ON, BUT NO SOUND COMES FROM THE SPEAKERS Check the following steps: Low level mode: Are the RCA cables on the head unit and on the amplifier correctly connected? • The RCA cables are correctly connected. Then an RCA cables could be defective. Check the function of the RCA cables on another audio device. If necessary, replace the defective RCA cables.
ENGLISH TROUBLE SHOOTING DISTORTION OR HISSING NOISE CAN BE HEARD FROM THE SPEAKERS Check the following steps: Is a input level controller on the amplifier set too high? Slowly turn the controller back until you hear a clean audio signal. Is the Bass Boost controller on the amplifier set too high? Slowly turn the controller back until you hear a clean audio signal.
ENGLISH AMPLIFIER ACTIVATES THE PROTECTIVE CIRCUIT / THE PROTECT LED LIGHTS UP Check the following steps: Short circuit on the speaker cables • First disconnect all speaker cables from the amplifier. Use a multimeter to check the ohmic impedance of each loudspeaker by measuring between its plus and minus lines. With standard loudspeakers the value fluctuates between 3 and 5 ohms. The values for low-resistance subwoofers can be lower. • The measurement shows a resistance value of less than 0.
DESIGN Audio Design GmbH Am Breilingsweg 3 · D-76709 Kronau/Germany Tel. +49 7253 - 9465-0 · Fax +49 7253 - 946510 www.esxaudio.de · www.audiodesign.de © Audio Design GmbH, all rights reserved. Technical changes, errors and mistakes reserved.