OWNER’S MANUAL CERAMIC UTILITY HEATER 10” | 1500 / 750W MODEL 1VAHCU10
CONTENTS (Continued) TECHNICAL DATA Model: 1VAHCU10 Voltage: 120V~ / 60Hz Watts: 750W Low / 1500W High BTUs: 5120 Features: • Adjustable Thermostat • Three Settings: High / Low / Fan Only • Top Mounted Control Panel • Power and Caution Indicator Lights • Safety Overheat Protection • Convenient Stay Cool Carry handle • Quiet High Efficiency Fan • Sturdy Metal Body CONSUMER PRODUCT INFORMATION For your own records, please attach a copy of your sales receipt to this manual.
CONTENTS Safety Guidelines.....................................................................................4-6 Usage........................................................................................................ 7-8 Assembly Instructions.............................................................................7 Heater Operation.....................................................................................7 Power / Caution Lights..........................................................
SAFETY GUIDELINES INTENDED USE: This product is intended for indoor residential and office use only, not for industrial or other commercial application. Use only with electrical wiring that is in good working order and that meets applicable codes and ordinances. This heater must be plugged in to a 120V AC, 15 Amp. (or larger) circuit. Do not plug anything additional into the same circuit. If you have any questions whether your wiring is adequate, consult a qualified electrician.
SAFETY GUIDELINES (Continued) • Use your heater only in dry environments. This heater is not intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools or other sources of water. Never locate heater where it may fall into a bathtub or other water container. Do not use in damp environments such as flooded basements. • Do not place the heater on a small, unlevel, uneven or any surface which might allow heater to tip or fall.
HEADLINE SAFETY GUIDELINES (Continued) WARNING: HOT SURFACES Do not touch body of heater when in use. This heater is hot when in use, to avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. WARNING: FIRE HAZARD Heater has hot and arcing or sparking parts inside. Do not use near combustible materials or flammable gases or sources of heat. DO NOT USE in areas where gasoline, paint or flammable materials are used or stored.
USAGE ASSEMBLY INSTRUCTIONS Simple assembly is required before you use this heater. 1. Remove Screw “A” on both sides of heater using a phillips screwdriver. 2. Rotate base cradle to align Hole “B” with new open hole from screw “A”. 3. Replace screw “A” through screw hole “B” on both sides of heater. 4. Heater is now ready for use. BEFORE AFTER HEATER OPERATION Always operate the heater in the upright position following all instructions and recommendations listed in this manual.
USAGE (Continued) TURNING HEATER ON To start the heater, turn the On/Off Power Level Control from the OFF position to the LOW or HIGH setting. Then rotate the Thermostat Control clockwise to the HIGH THERMOSTAT position as described below. (During the heaters initial use, you may experience a slight odor or smoking. This is the result of the heating element lubrication “burning off”. This is normal and will go away after a few minutes of use.
USAGE (Continued) TO OPERATE FAN ONLY Turn the On/Off Power Level Control dial to the Fan setting. Turn thermostat fully clockwise so the fan will run continuously TURNING OFF Turn the center dial to the OFF position before unplugging or plugging in the heater. Heater should be unplugged when not in use. IMPORTANT SAFETY FEATURES The power indicator light, located near the control panel, lights whenever the heater or fan is turned on.
CARE AND MAINTENANCE CLEANING CAUTION-Before cleaning the heater be sure to disconnect power cord and allow the heater to cool completely. This heater should be cleaned at least once a year to maintain proper performance. Clean the outside surface with a clean, damp cloth. Do not use harsh chemical or abrasive cleaners. DO NOT IMMERSE THE HEATER IN WATER. Allow heater to dry completely before use. REPAIR DO NOT OPERATE THE HEATER WITHOUT THE GRILLE IN PLACE.
4560 W. 160th Street Cleveland, OH 44135 833-950-1185 | support@visionairproducts.com www.visionairproducts.
