Thank you for purchasing N8760B Digital Satellite Receiver. This manual will help you to install, use and maintain the receiver. Please read this manual carefully before operating your unit and keep it for future reference. Warning & Note In this manual, pay special attention to the following marks that indicate hazardous situations. Warning: Alert user to the operation which could result in device damage or data loss, and the presence of a hazardous situation which could result in serious injury.
User’s Manual Safety Instruction Read following items carefully before operating this receiver. Installation This receiver should be installed horizontally. Unbalanced installation may cause damage.
User’s Manual v Replace batteries if there is no enough power and dispose battery waste properly for environmental protection. Others v All-pole power switch of this receiver is on rear panel. Switch it to “I”, related equipment will connect with power supply. Switch it to “o”, related equipment will disconnect with power supply completely. v Only use accessories specified by the manufacturer, as other unsupported accessories may cause damage to the receiver.
User’s Manual Contents 1. Before Using the Receiver .................................................................................................. 3 1.1 Main Feature ................................................................................................................. 3 1.2 Front Panel ................................................................................................................... 4 1.3 Conditional Access (CA) ...............................................................
User’s Manual 9. Edit Channel ....................................................................................................................... 26 9.1 Delete Channel ........................................................................................................... 26 9.2 Lock Channel .............................................................................................................. 27 9.3 Move Channel ................................................................................
User’s Manual 1. Before Using the Receiver 1.1 Main Feature PVR supported Time shift supported Dolby 5.
User’s Manual 1.2 Front Panel Name Function 1. Switch between operation and standby modes 2. IR Receive infrared remote control signal 3. DISPLAY Display status 4. MENU Display/exit from main menu 5/9. Adjust volume or move cursor left/right 6. OK Display channel list or confirm operation 7/8. Switch channels or move cursor up/down 10. USB slot Connect to specific USB device 11. Smart card slot Open the cover to insert smart card 1.
User’s Manual 1.4 Rear Panel Name Function 1. LNB IN Connect to satellite dish 2. LOOP OUT Loop output RF signal to another receiver 3. HDMI Output video and audio signal to TV (support high definition output) 4. Y/Pb/Pr Output Y/Pb/Pr video signal to TV (support high definition output) 5/6. R/L-AUDIO Output right/left audio signal to TV or amplifier 7. VIDEO Output CVBS video signal to TV 8. S/P DIF Output digital audio signal to amplifier 9. 100-240V~ AC power supply 10.
User’s Manual 1.5 Remote Control Unit (RCU) Name Function 1. Learning keys Please refer to Learning Key. 2.
User’s Manual 3.
User’s Manual Learning Key The receiver RCU has some learning keys at the upper part. The keys (except SET key) can be used to memorize corresponding key values of TV RCU. After learning, you can realize remote control for TV with the receiver RCU. The recommended keys are TV POWER, TV/AV, VOL+ and VOL- of TV RCU. The identifier of TV/AV key varies with different types of TV RCUs. Instruction: 1.
User’s Manual 2. Installation Connect TV and other devices, then you can power on the receiver and search channels. 2.1 Signal Input Connect LNB IN port on the receiver to satellite dish with an RF cable. 2.2 Connect TV Please choose one of following 3 ways to connect TV. 1. Connect TV Using HDMI Cable Connect HDMI port on the receiver to HDMI port on TV.
User’s Manual 2. Connect TV Using YPbPr Cable 1. Connect Y (green)/Pb (blue)/Pr (red) ports on the receiver to Y/Pb/Pr ports on TV. 2. Connect R-AUDIO (red)/L-AUDIO (white) ports on the receiver to corresponding ports on TV. 3. Connect TV Using RCA Cable 1. Connect VIDEO (yellow) port on the receiver to corresponding port on TV. 2. Connect R-AUDIO (red)/L-AUDIO (white) ports on the receiver to corresponding ports on TV.
User’s Manual 2.3 Connect other Device For connection of other devices, please refer to following figure: Connect LOOP OUT port on the receiver to LNB IN port on another receiver. Connect S/P DIF port on the receiver to corresponding port on amplifier with an S/P DIF cable, or connect R-AUDIO (red)/L-AUDIO (white) ports on the receiver to corresponding ports on amplifier. Note: If you encounter any problem during the connections, please contact your local operator. 2.4 Power on 1.
User’s Manual 3. Basic Operation This part describes operations such as channel switch, volume control and other basic operations when playing program. 3.1 Channel Switch You can switch channels using following methods: 1. Select Next/Previous Channel Press keys to select next/previous channel. 2. Select Channel by Channel Number 1. Press number keys to input a channel number. 2. Press OK key or wait for 3 to 5 seconds to play it in full screen. 3.
User’s Manual 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Detailed information of current/next program Channel number and name TV/radio mode icon Current program play progress Current and next program information Current audio mode Decoding standard Standard/high definition mode icon Current time Icons Bright if current channel is a favorite channel. Bright if current channel is a scrambled channel. Bright if current channel is a locked channel. Bright if current channel has Teletext information. 3.
User’s Manual 3.7 Subtitle 1. If “Subtitle” is set to “On” in 10.2 Video Set, press SUBTITLE key to display Subtitle list. keys to select a language and press OK key to confirm. The Subtitle is dis2. Press played at the bottom of screen. If you want to switch Subtitle off, select “Close Subtitle” in Subtitle list and press OK key to confirm. Note: This function needs your local operator support. 3.8 Closed Caption (CC) Press CLOSECAPTION key to switch on/off Closed Caption.
User’s Manual Press keys to select 30s, 60s, 90s, 120s or OFF. Divide Record by EPG Event You can record programs in several files according to EPG events, such as news, weather report, etc. Select “OFF” to record programs in one file, or select “ON” to record programs in several files according to EPG events. PVR Icon Time out Set on screen duration of PVR icon. keys to select Always, 5s, 10s, 30s or 60s. If “Always” is selected, PVR icon is Press displayed on screen all through the recording.
User’s Manual 1. Add Schedule 1. Press Green key to display add schedule window. 2. Set schedule parameters as follows: keys to select Rec or Schedule Type: Press Play. Schedule Start Time: Press OK key to display calendar window. Set schedule start date and time according to screen information. Schedule End Time: Press number keys to input end time. keys to select Once, Schedule Mode: Press Daily or Weekly. If “Weekly” is selected, press OK key to pop up weekday group window.
User’s Manual Index: Press keys to select R1 or R2. Mode: Display recording mode Quick or Schedule. Channel Name: Display channel name. File Name: You can rename the file if needed. Press OK key to pop up a keyboard. For detailed operations, please refer to 8.3 Rename Satellite. Valid Record Time: Display valid record time. Past Time: Display past time. keys to select a recording duration. System will record according to the Duration: Press modified duration.
User’s Manual 4. Playback Progress Bar If you press INFO key, playback progress bar is displayed. It displays current file information, playback progress and operation help information. 1. TV icon 2. File name 3. File group name 4. Decoding standard 5. Standard/high definition mode icon 6. Watching point time (hh:mm:ss)/total time (hh:mm:ss) 7. Playback progress 8. Operation help information 5. Jump backward/forward 1. Press INFO key to display playback progress bar.
User’s Manual 3. Press Green key to delete it. 8. File Cut You can cut out some parts of recorded files. These parts will be skipped while playback file. 1. Press INFO key to display playback progress bar. 2. Press OK key to enter file cut mode. 3. Select a time point, and press Green key to set start point. 4. Select a time point, and press Yellow key to set end point. 5. After pressing OK key, a message box pops up for confirmation. 6.
User’s Manual Create Group Press Green key to pop up a keyboard. For detailed operations, please refer to 8.3 Rename Satellite. Delete Group 1. Press keys to select a group. 2. After pressing Red key, a message box pops up for confirmation. 3. Select “OK” and press OK key to confirm or select “Cancel” and press OK key to cancel the operation. Rename Group keys to select a group. 1. Press 2. Press Yellow key to pop up a keyboard. For detailed operations, please refer to 8.3 Rename Satellite. 3.
User’s Manual 1. 2. 3. 4. 5. 6. 7. TV icon Channel name Decoding standard Standard/high definition mode icon Watching point time (hh:mm:ss)/total time (hh:mm:ss) Playback progress Operation help information 2. Stop Time Shift Press STOP key or switch to another channel to stop time shift and return to play live program. 5. USB Application You can play MP3 and browse photo. Notes: USB device should be connected to USB port on front panel before operation.
User’s Manual The icon in bottom left corner of window displays used and free space of USB device. If you want to delete recorded files, please refer to corresponding operations in 4.6 Edit Recorded File. 6.2 Format USB Device Warning: This function will format your USB device, and all files will be deleted. Select Main Menu → PVR → HDD Format and press OK key to enter. 1. Highlight “OK” and press OK key, a warning box pops up for confirmation. 2.
User’s Manual Blue key: Display book list window 7.2 Schedule Program 1. Press keys to select a future program. 2. Press OK key to pop up EPG schedule window. 3. Set schedule type and mode. For detailed operations, please refer to 4.3.1 Add Schedule. 4. Move cursor to “OK” and press OK key to save the new schedule. The scheduled program is marked with “ ”. If you want to cancel this setting, press OK key again. 5. Press EXIT key to save and exit.
User’s Manual receiver. Position Set: For detailed operations, please refer to 8.2 DiSEqC1.2. keys to select a transponder (TP). You can also press OK key to TP Setup: Press display TP edit window. For more details, please refer to 8.4 Transponder (TP) Edit. 4. Press EXIT key to save and exit. 8.2 DiSEqC1.2 Note: The settings of motor control should be operated by qualified personnel, otherwise the satellite dish may not work properly. These settings are for motor control of satellite dish.
User’s Manual Select characters on the keyboard with arrow keys and press OK key to input. Select “Clear” and press OK key to delete all characters on title bar. Select “Caps On” and press OK key to switch between capital and lowercase. Select “Back” and press OK key to delete last character on title bar. Select “OK” and press OK key to confirm renaming. Select “Cancel” and press OK key to cancel renaming. 4. After renaming, the new satellite name appears in satellite list. 8.
User’s Manual 1. Satellite Search Search channels according to all preset TPs of the selected satellite. keys to select one satellite, and press OK key to confirm. 1. Press 2. Press Red key to pop up select search mode window. 3. Set parameters as follows: keys to select FTA or Search Mode: Press FTA+SCR. keys to select ALL (TV Service Filter: Press and radio), TV (only TV) or Radio (only radio). keys to select “ON” to search NIT: Press channels according to NIT. 4.
User’s Manual 9.2 Lock Channel 1. Press keys to select a channel. 2. Press Yellow key to lock this channel and mark it with “ ”. If you want to cancel this setting, press Yellow key again. Note: System password is required to view programs of the locked channels. 9.3 Move Channel 1. Press keys to select a channel. 2. Press Blue key to mark this channel with “ ”. 3. Press keys to move it to a new position and press Blue key to confirm. 9.4 Set Favorite Channel 1. Press keys to select a channel. 2.
User’s Manual the video appears normally. Aspect Mode: Press keys to select Letter Box, PanScan or Default. keys to select 4:3, 16:9 Aspect Ratio: Press or Auto. Subtitle: Select “On” to display Subtitle automatically if available. keys to select a proper Resolve: Press resolution. Note: If your TV does not support the selected resolution, there is no video output on screen. keys until In this case, continue to press the video appears again. keys to select Stereo, Left or Right.
User’s Manual 10.5 Parental Guide (PG) You can set PG lock level for programs and modify PG password. 1. PG Lock Level Select Main Menu → Maintenance → Advance Set → PG Lock Level and press keys to select a PG lock level. After setting, press EXIT key to save and exit. Note: PG password is required to view programs beyond the set level. 2. Modify PG Password PG password is required to view programs beyond the set PG lock level. The default password is “0000”. You can modify it if necessary. 1.
User’s Manual 12.3 Loader Status This window displays information about loader, such as firmware version, loader version, etc. Select Main Menu → Maintenance → Information → Loader Status and press OK key to enter. 12.4 Components This window displays information about the components of this receiver. Select Main Menu → Maintenance → Information → Components and press OK key to enter. 12.5 Mail Information All mails received from your local operator are displayed in mail information window.
User’s Manual 13. Appendix 13.1 Trouble Shooting DISPLAY on front panel is off 1. Power cord is disconnected. Make sure power cord is plugged into a proper power socket. 2. The receiver is turned off. Turn it on. DISPLAY on front panel is on, but no sound and picture on TV screen key to switch it to operation mode. The receiver is in standby mode. Press No signal 1. Signal cable is disconnected. Connect signal cable correctly. 2. Program parameters are set wrongly. Set correct parameters. 3.
User’s Manual 13.2 Specification Tuner Frequency 950 ~ 2150MHz Level -65 ~ -25dBm Impedance 75Ω LNB Supply 13V/18V/OFF, 450mA max. Channel Decoding Standard DVB-S EN300421, DVB-S2 ETSI TR102 376 Demodulation QPSK, 8PSK Symbol Rate 2.
User’s Manual 13.