VisionStat ® 5.6” and 7.0” Wired Video Monitoring Systems MA-BCKS-5.6 Models MA-BCKS-7.0 Models Installation & User Manual Please read this manual thoroughly before operating the device and keep this document for future reference www.mobileawareness.
Mobile Awareness Mobile Awareness, LLC VisionStat® Manufacturer’s Limited Warranty 1-Year Limited Warranty (Revised 6/2010) Limited Warranty VisionStat™Limited Warranty Mobile Awareness warrants to the original end-user purchaser that a new VisionStat™ Color Camera System is free from structural defects in material and workmanship and agrees, without charge, to repair or replace any part(s) which fails in normal use and service because of structural defects in material and workmanship.
VisionStat 5.6” and 7.0” Wired Video Monitoring Systems Contents of Manual 1. 2. 3. 4. 5. 6. 7. 8. 9. Product Overview, Product Features, Product Specifications………………..….…..5 VisionStat Package Contents, Optional Items and Accessories........………............6 About the Monitor.....................................................................................................6 About the Cameras...............................................................................................
Mobile Awareness Storage and Keeping 1. 2. 3. 4. 5. 6. 7. 8. 9. Do not expose the Monitor, Cameras or other equipment to excessive heat or cold. Please read and follow the technical specifications provided in this manual. Never use the device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places. Never use the device in environments with excessive moisture, dust or smoke. Avoid dropping or striking the device.
VisionStat 5.6” and 7.0” Wired Video Monitoring Systems Product Overview VisionStat is an advanced family of wired and wireless Video Monitoring Systems. Featuring high-quality 5.6” and 7.0” Digital Color LCD Monitors, VisionStat Video Monitoring Systems can be configured for up to four (4) ruggedized infrared night vision CCD Cameras with multiple mounting options.
Mobile Awareness VisionStat Wired Package Contents (Hardware) Monitor 5.6” Wired Monitor (P/N: MA-LCDS-5.6) 7.0” Wired Monitor (P/N: MA-LCDS-7.
VisionStat 5.6” and 7.0” Wired Video Monitoring Systems About the Cameras The standard Camera issued with the system is the 18IR Camera which has a 120 degree viewing angle and is rated IP68. This Camera comes equipped with 18 infrared LEDs to provide night vision up to 12 meters. It is mounted on a “U-Bracket” which allows the user to angle the Camera up or down. The Side Camera is typically featured in triple Camera systems.
Mobile Awareness Installation: Monitor and Wiring Harness (Continued) Before applying power to the system; make any Camera and trigger wire connections. The 22-pin wiring harness’ wiring connections can be seen in the chart below. The RCA connectors can be used to connect a second Monitor to the system for secondary viewing.
VisionStat 5.6” and 7.0” Wired Video Monitoring Systems Installation: Cameras Each Camera will have a 4-pin connection and be connected to the Monitor’s 22-pin wiring harness via an extension cable. The extension cables come in lengths of 5M, 10M and 20M. The length of the cable used should be determined by the length of the vehicle, including any passageway or route you take through the vehicle’s body to ensure a safe and secure connection.
Mobile Awareness Installation: Cameras (Continued) If the Camera cable will run through the vehicle body (see Figure 12), drill a 20mm hole in order to pass the 4-pin connection through. Once this connection is made, it may be placed inside the vehicle body for additional protection. The rubber grommet on the Camera’s cable can be used to plug the 20mm hole. Seal the hole properly with waterproofing compound, as well as anywhere cables run through openings in the vehicle body.
VisionStat 5.6” and 7.0” Wired Video Monitoring Systems Installation: Side Cameras (Continued) If the viewing angle needs to be adjusted, loosen the Camera Body Nut and rotate the Camera Angle Adjustment Rings until the proper viewing position is achieved. Once properly positioned, hand tighten the Camera body nut securely.
Mobile Awareness Menu (Continued) 3) System: The System menu will give you the option of which type of Color-System to use, turning the blue Back Screen on or off, the horizontal and vertical adjustments, as well as zoom. Press the CH– button on the Monitor to scroll up and down to select your desired function. Press the ▲☼/▼☼ buttons on the Monitor in order to adjust the level of each setting. Color System: Select between PAL/AUTO/NTSC Blue Back: Select between turning the Blue Back Screen on or off.
VisionStat 5.6” and 7.0” Wired Video Monitoring Systems Maintenance & Troubleshooting (Continued) Symptom Possible Causes and Solution No reversing function Check that the correct corresponding color coded trigger wire is connected properly. For example, the rear Camera is typically connected to the BROWN 4-pin connector, so the BROWN trigger wire would need to be used to toggle the Monitor to that channel, in this case, Channel 3.
Mobile Awareness Notes 14
VisionStat 5.6” and 7.
www.mobileawareness.com BCKS-2102-INS-R1.
