User Manual

ManualsBrandsVisonic ManualsElectronicsPIR detector with curtain lens

D-303370 CLIP PG2 Installation Instructions 1

CLIP PG2

CLIP PG2CLIP PG2

CLIP PG2

Wireless PowerG Two-way Curtain PIR Detector

Installation Instructions

1. INTRODUCTION

1. INTRODUCTION1. INTRODUCTION

1. INTRODUCTION

The CLIP PG2 is a small and elegant wireless curtain-pattern PIR detector for indoor use and designed for easy installation.

Modern technology is used to include 3 different detectors in a single case, each programmable for optimized performance at the specific

mounting location. This results in better catch performance and virtually no false alarms.

The superiority in performance of this detector is achieved by applying an improved version of the patented True Motion Recognition™

(TMR) algorithm. This advanced motion analysis method allows the CLIP PG2 to distinguish between the true motion of the human body

and any other disturbances that cause false alarms.

The CLIP PG2 includes the following features:

• 2-way PowerG protocol communication

• Very low current consumption

• Microprocessor-controlled temperature compensation

• Sealed chamber protects the optical system

• Front cover tamper switch

• Optional back tamper switch

• White light protection

• Elegantly styled, sturdy case

• RF Link quality indication

Detailed coverage patterns and mounting alternatives are illustrated in Figures 2 through 6.

Figure 1. CLIP PG2 General View

Figure 2. Wall-Mount Curtain

Figure 3. Ceiling-Mount Curtain

Figure 4. Overhead Curtain

Figure 5. Curtain / Pet Alley

Figure 6. CLIP PG2 on Internal Doorframe

A. This side up

E. 3.6 m (12 ft) max. distance

B. 6 m (20 ft) max. distance

F. Detection curtain

C. 1 m (3.3 ft) max. width

G. Option A

D. 0.5 m (1.65 ft) max. width

H. Option B

. .

. INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION

2.1 General Guidelines

Summary of content (6 pages)

PAGE 1
CLIP PG2 Wireless PowerG Two-way Curtain PIR Detector Installation Instructions 1. INTRODUCTION The CLIP PG2 is a small and elegant wireless curtain-pattern PIR detector for indoor use and designed for easy installation. Modern technology is used to include 3 different detectors in a single case, each programmable for optimized performance at the specific mounting location. This results in better catch performance and virtually no false alarms.
PAGE 2
.2 Regular Mounting A. Enroll button E. LEDs B. Front tamper switch F. Back tamper switch (optional) C. RF Module G. 3 Volt Lithium battery A. Back tamper switch A back tamper alert is activated when the base is detached from the wall. D. Sensor Figure 8. Back Tamper (Rear) View Figure 7. Internal View ATTENTION! The back tamper switch becomes functional only when the break-away segment is secured to the wall with a screw.
PAGE 3
2.3 Bracket Mounting Note: When mounting using the bracket, the back tamper becomes inoperative. A 1 * ** 1. Drill two 7 mm (1/4") holes at the marked locations Figure 10. Drilling Holes 2 1 1. Drill two holes in the mounting surface. 2. Secure the bracket with two screws. A. Mounting surface Note: The bracket provides two mounting options For optimum angle coverage: ∗ use these two holes to increase the coverage range by 5•° ∗∗ use these two holes to increase the coverage range by 10•° Figure 11.
PAGE 4
A. Window A A Note: The CLIP PG2 can be mounted on either side of a window. Figure 14. Mounting on Both Sides of a Window 2.4 Setting the Coverage Range The CLIP PG2 can be programmed to select one of three ranges, according to the type of installation, for the curtain beams (see Figure 15 and section 2.7). A. Minimum range B. Medium range C. Maximum range Figure 15. Range Setting Diagram 2.5 Walk Testing A. Mount the cover and tighten the screw.
PAGE 5
3. LOCAL DIAGNOSTICS DIAGNOSTICS TEST A. Separate the base from the cover (see Fig. 8). B. Put back the cover to return the tamper switch to its normal (undisturbed) position, and then secure the front cover to the base with the case closure screw (see Fig. 9). C. The CLIP PG2 will enter a 1 min. stability period. During this time the red LED blinks. D. Walk-test the coverage area.
PAGE 6
Nominal Battery Capacity Battery Life (for typical use) FUNCTIONAL Visual indications: Alarm Period WIRELESS Frequency Band (MHz) Communication Protocol Supervision Tamper Alert MOUNTING Height Installation Options ACCESSORIES ENVIRONMENTAL RFI Protection Operating Temperatures Storage Temperatures PHYSICAL Size (H x W x D) Weight (with battery) Color Compliance with Standards PATENTS 1450 mA/h 7 years Red LED lights for about 2 seconds upon motion detection in the walk test mode and for about 0.2 sec.