Installation and Operating Instructions

Product documentation
HTD-432 PG2 (915-0:025)/HTD-432 PG2 (868-0:025)/HTD-432 ME PG2 (868-0:025) wireless heat
detector
To download the full manual for this product, go to https://www.visonic.com/download-center or scan the QR code.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules and with ISED license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le
fonctionnement.
To comply with FCC Section 1.1310 for human exposure to radio frequency electromagnetic fields and IC requirements,
implement the following instruction: A distance of at least 20 cm between the equipment and all persons should be
maintained during the operation of the equipment.
Le dispositif doit être placé à une distance d'au moins 20 cm à partir de toutes les per-sonnes au cours de son
fonctionnement normal. Les antennes utilisées pour ce produit ne doivent pas être situés ou exploités conjointement avec
une autre antenne ou transmetteur.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that
interference will not occur in a particular installation. If this device does cause such interference, which can be verified by
turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following
measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one that supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
NOTE: FCC statement only applies to 915MHz version
Innovation Science and Economic Development Canada (ISED) Statement
This equipment complies with FCC and ISED Canada RF radiation exposure limits set forth for an uncontrolled
environment.
IC: XXXXXX. The term IC before the radio certification number signifies that the ISED technical specifications were met.
This Class B digital apparatus complies with Canadian ICES-003. This device complies with RSS-247 of ISED. Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Innovation, Sciences et Développement économique Canada (ISDE)
Le present appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Ce dis-positive satisfait aux
exigences d’ISDE, prescrites dans le document CNR-247. son utilisation est autorisée seulement aux conditions suivantes:
(1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the
“Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve (12)
months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated under
conditions of normal use in accordance with the Manufacturers recommended installation and operation instructions.
Products which have become defective for any other reason, according to the Manufacturers discretion, such as improper
installation, failure to follow recommended installation and operational instructions, neglect, wilful damage, misuse or
vandalism, accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by
this Warranty.
There is absolutely no warranty on software, and all software products are sold as a user license under the terms of the
software license agreement included with such Product.
The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product
will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery, fire or otherwise,
or that the Product will in all cases provide adequate warning or protection. The Product, properly installed and maintained,
only reduces the risk of such events without warning and it is not a guarantee or insurance that such events will not occur.