User Manual

2 D-303486 KF-235 PG2 User's Guide / Guía del usuario / Guia do utilizador
Step Functions User Actions ARM/DISARM LED Indication
2
LATCHKEY
Blue LED above AWAY button lights
3
PANIC alarm*
Press the
and buttons simultaneously ( 2 sec.)
-
4
AUX
According to the state of the alarm system, see section 2.2
“ For UL Listed product, “PANIC” is for Ancillary Use only.
3.2 Keyfob Response
When executing a command, the keyfob's Transmission LED blinks red once to indicate transmission of the command to the control panel. If the
operation is successfully completed, the green LED lights momentarily and a "happy tune" is heard. If the operation fails or cannot be
completed, for example, when the system is "not ready", the red LED lights steadily and a "sad tune" is heard. When executing a command and
there is a communication failure between the keyfob device and the control panel, the keyfob's Transmission LED remains off and no tune is heard.
3.2.1 Primary LED and Buzzer Response to Keyfob Commands
Panel Response Buzzer Indication Transmission LED Indication
Success: Operation is successfully completed
Happy (success) beep
Momentary GREEN
Fail: Operation failed
Sad (failure) beep
Momentary RED
No communication: For example, control panel is out of range.
None None
Keyfob low battery:
Note: If transmission is still possible despite the battery condition,
the unit will send a low battery signal to the control panel.
Depends on the operation that is performed Blinks yellow 2 sec.
Trouble in system:
Depends on the operation that is performed
Lights yellow 2 sec.
When forced arming (bypass zones) is performed, the keyfob buzzer “protests” by emitting a continuous tone during the exit delay for 5 seconds (for
more details, see the PowerMaster Installer Guide, section 5.5.2).
3.2.2 Arming LED indication
When executing a command using the keyfob device, the status of the control panel is indicated by the status LEDs that light blue.
System State ARM/DISARM LED Indication
Exit from DISARM to AWAY AWAY lights
Exit from DISARM to HOME HOME lights
Entry from HOME
DISARM blinks
Entry from AWAY
DISARM blinks
Exit from HOME TO AWAY
AWAY lights
Exit from AWAY TO HOME
HOME lights
Installer mode, Sync mode or when the system is otherwise reachable but unavailable
AWAY, HOME, DISARM all blink twice, wait, then blink twice again
4. MAINTENANCE
4.1 Replacing the Battery
When the keyfob device stops operating due to low battery and until the time the battery is completely depleted, all LEDs will light blue.
A replacement 3V battery, VARTA CR-2032, is available from hardware and electrical supply stores. Replace the battery as shown in Figure 2.
Caution! Battery may explode if replaced by incorrect type or if mistreated. Do not recharge, disassemble, or dispose of the battery in fire.
4.2 Cleaning
Clean the keyfob only with a soft cloth or sponge moistened lightly with a mixture of water and mild detergent, and wipe it dry immediately.
The use of abrasives of any kind is strictly forbidden. Also never use solvents such as kerosene, acetone or thinner.
4.3 Periodic Test
Wireless equipment should be tested regularly to determine whether there are sources of interference and to protect against faults.
Refer to the PowerMaster Installer Guide, Chapter 6 Periodic Test, for instructions on how to conduct a periodic test.
5. TROUBLESHOOTING
Problem Diagnosis Proposed actions
Keyfob does not enroll 1. Keyfob was pre-enrolled 1. Enroll the keyfob again in the vicinity of the control panel.
2. The wrong ID number was
entered
2. Reenter the ID number
3. No free location 3. If the maximum number of keyfobs has already been enrolled the alarm system
will not allow enrolling any more keyfobs.
4. Unknown device 4. Make sure the frequency used for the device is the same as the control panel
frequency.
Keyfob LED does not light when
button is pressed
Low battery condition
Replace the battery
CAUTION! Wireless control panels may be blocked by radio signals occurring on or near their operating frequencies.