User's Manual

ManualsBrandsVisonic ManualsElectronicsTouch Screen Keyprox

D-303169 KP-160 PG2 User’s Guide 1

KP-160 PG2

Touch Screen Keyprox

User’s Guide

Table of Contents

1. INTRODUCTION..........................................................................................................2

2. INSTALLATION............................................................................................................3

2.1 Inserting Battery..................................................................................................3

2.2 Closing Battery Compartment Cover.................................................................. 3

2.3 Wall Mounting Options .......................................................................................4

2.4 Enrolling the KP-160 PG2...................................................................................6

2.5 Configuring the KP-160 PG2 Parameters...........................................................6

2.6 Enrolling Proximity Tags.....................................................................................8

3. USING THE TOUCH SCREEN KEYPROX..................................................................9

3.1 Arming and Disarming the System .....................................................................9

3.2 Initiating Alarms................................................................................................10

3.3 System Status and Indications .........................................................................10

3.4 Bypassing Zones..............................................................................................14

3.5 Controlling Home Automation Devices.............................................................14

3.6 Other Functions................................................................................................15

APPENDIX A: SPECIFICATIONS..................................................................................15

APPENDIX B: COMPLIANCE WITH STANDARDS.......................................................16

Summary of content (17 pages)

PAGE 1
KP-160 PG2 Touch Screen Keyprox User’s Guide Table of Contents 1. INTRODUCTION .......................................................................................................... 2 2. INSTALLATION............................................................................................................ 3 2.1 Inserting Battery.................................................................................................. 3 2.2 Closing Battery Compartment Cover ....................................
PAGE 2
1. INTRODUCTION KP-160 PG2 is a 2-way wireless PowerG touch screen keyprox for the PowerMaster family control panels. The KP-160 PG2 enables most common everyday user functions:  Arm and Disarm the alarm system.  Initiate Emergency, Fire and Panic alarms.  Control home automation devices.  Review system status.  Perform programmable predefined functions. KP-160 PG2 is operated by proximity tags.
PAGE 3
2. INSTALLATION 2.1 Inserting Battery CAUTION! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to manufacturer's instructions. Figure 1 – Battery Insertion Insert two 1.5V batteries in each slot while ensuring battery polarity. 2.
PAGE 4
Figure 2 - Battery Cover Mounting (part a) Wall-mounted Installation (Using Battery Cover without Tamper Hole – see "A") Figure 3 - Battery Cover Mounting (part b) A. Tamper B. DC Power Connection 2.3 Wall Mounting Options The KP-160 PG2 unit mounting options are illustrated in the following drawings. Wall Mounting Figure 4a – Wall Mounting 1. Drill 3 mounting holes 2. Position the bracket and secure with 3 screws 4 3. Attach the unit to the bracket 4.
PAGE 5
Wall Mounting with External Electrical Connector Figure 4b – Wall Mounting with External Electrical Connector 1. Secure bracket with 2 screws as shown in the two drawings above. 2. Attach the unit to the bracket. 3.
PAGE 6
2.4 Enrolling the KP-160 PG2 Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu. A flowchart of the procedure is provided below. Step Action 1 Enter the Installer menu and select “02:ZONES/DEVICES” 2 Select "ADD NEW DEVICE" Option See Note LCD Display 02.ZONES/DEVICES  ADD NEW DEVICES   MODIFY DEVICES 3 4 Enroll the device or enter the 7-digit code that appears on the device's sticker.
PAGE 7
Note: Every 5 minutes the keyprox performs a communication test session with the control panel (i.e. "Supervision signal) to check the integrity and quality of the Radio link. If the keyprox does not report a supervision signal at least once within a predefined time, a “MISSING” trouble alert is initiated. Therefore, if you take the keyprox out of the protected premises, switch the Supervision OFF to avoid the trouble alert.
PAGE 8
unit(s) or the device wired to the PGM output. For more details on configuring the X-10/PGM output functions, see the corresponding sections of the control panel’s Installer Guide (“OUTPUTS” menu) and User Guide (“SCHEDULER” menu). Option settings: Not Used, Status (default); Stop Beeps, Skip exit delay; and X-10 (PGM). * Applicable only to control panels that support the voice option. AC POWER Connect Define whether or not to report power failure.
PAGE 9
3. USING THE TOUCH SCREEN KEYPROX 3.1 Arming and Disarming the System Step Operation User Actions (1) Select a PARTITION (if Partition is enabled) 2 Arm AWAY Optional 1 Keyboard & Panel Response The selected key blinks. Any combination of + [ ] Arm HOME + [ ] Disarm (OFF) Optional + 3 ] Quick arm AWAY (If Quick Arm is enabled) ( 2 sec.) (3) INSTANT ( 2 sec.) ( ) begin to blink and prompt you to present your Tag.
PAGE 10
6. 7. For LATCHKEY activation, press the LATCHKEY key within maximum 8 seconds timeout period after completing the previous step. LATCHKEY is available only if the LATCHKEY feature is enabled in the PowerMaster control panel (see PowerMaster Installer Guide).You can perform the LATCHKEY and INSTANT functions, one after the other. The order is not important.  LATCHKEY and INSTANT functions can be operated only during exit delay.
PAGE 11
Icon/Key Indications Arming Indication ARM HOME DISARM EXIT DELAY Each icon appears one after the other ENTRY DELAY + The "Present Prox Tag" icon and DISARM key blink simultaneously If Partition is enabled, the arming indication of the first partition is displayed concurrently with the corresponding first partition key LED , then the second partition indication is displayed concurrently with the second partition key LED and then the third partition indication is similarly displayed.
PAGE 12
Number Indication [1] What it Means PGM/X-10 control mode. System is armed in LATCHKEY mode. Exit beeps are shut off. This mode disables when the exit delay is over. [2] System is armed in the INSTANT mode. A message is waiting in the system. The control panel is presently in "INSTALLER MODE" or "USER SETTINGS". Memory / Alarm in partition or system. The partition / system has an active trouble status that needs to be reviewed and cleared. [3] AC failure.
PAGE 13
number ( / / ) followed by the key. Upon each press of the key, the next zone number assigned to the pressed Partition number appears on the Zone # display.
PAGE 14
Notes: A zone which is BYPASSED and NOT READY is shown as BYPASSED ( ). When "00" appears on the Zone # display, this indicates a NOT READY state in the alarm system that is not related to any detector, for example, "tamper open" in a keypad or control panel. If all zones are READY and "not bypassed", the button is disabled. 3.
PAGE 15
3.6 Other Functions Output Function Actions AUX Function Response Enrollment: Long key press (more than 5 sec.) until green LED lights and then release key. Back to Factory: Long key press (more than 7 sec.) to reset the KP-160 PG2 device to factory default settings. Cancels current operation: Short key press Volume control Changes the volume level upon each key press. Volume level alternates between 1, 2, 3, 0 Mute exit beeps Mutes the exit beeps; small circle key will appear above the key.
PAGE 16
APPENDIX B: COMPLIANCE WITH STANDARDS This device complies with FCC Rules Part 15 and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 17
The technical documentation as required by the European Conformity Assessment procedure is kept at: UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ.