Installation Guide

ManualsBrandsVisonic ManualsElectronicsWireless Magnetic Contact

Table Of Contents

MC-303 PG+ Vanishing Door/Window

Magnetic Contact Installation Guide

Installation guidelines

The reference to MC-303 PG+ throughout this manual includes the model MC-303 P9M0.

CAUTION: Only qualified personnel may install this equipment. Place this device in non-

hazardous indoor locations only.

Important: Check the device and the entire alarm system weekly to ensure optimal

performance.

Note:

To comply with FCC RF exposure compliance requirements, locate the device at a distance of at

least 20 cm from all persons during normal operation.

Do not co-locate the antennas used for this product, or operate them in conjunction with any

other antenna or transmitter.

Figure 1: MC-303 PG+

Callout Description

A Magnet

B Device

C Battery pull-tab

D Positioning marks

For more information refer to section About MC-303 PG+.

D-308437

*D-308437*

D-308437 MC-303 PG+ Rev. 0

Summary of content (10 pages)

PAGE 1
MC-303 PG+ Vanishing Door/Window Magnetic Contact Installation Guide Installation guidelines The reference to MC-303 PG+ throughout this manual includes the model MC-303 P9M0. CAUTION: Only qualified personnel may install this equipment. Place this device in nonhazardous indoor locations only. Important: Check the device and the entire alarm system weekly to ensure optimal performance.
PAGE 2
Enrolling the device 1. 2. 3. 4. 5. Refer to the control panel installation manual for the complete set of enrollment instructions and testing procedures. From the Installation menu, enter the Device enrollment menu and select the option to add a new device. Remove the battery pull-tab to power on the device and begin the auto-enrollment process. If the battery pull-tab is not available or if the device does not automatically enroll, open the device cover to trigger the enrollment.
PAGE 3
2. Callout Description A Double-sided adhesive tape Place the device on the frame of a window or door and place the magnet on the moving surface of the window or door itself, directed according to the positioning marks. See the following figure. Figure 3: Device and magnet position on door and door frame Mounting the device using screws 1. To open the device cover, insert and turn a 4mm flat screwdriver into the four corners of the device . Figure 4: Device cover removal 2.
PAGE 4
Callout Description A Screwing device base B Break-away segment C Closing the device cover Replacing the battery Before you begin: CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the manufacturer's instructions and according to local rules and regulations. WARNING: This product contains a coin battery. If it is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
PAGE 5
Figure 6: Battery removal and insertion 5. 6. Press down on the battery until it fits into place. Close the device cover. See figure 5 C. Note: After restoring a low battery, the system may take up to 5 minutes to clear the trouble. Directional magnet distances for event triggers The following figure and table display the directional magnet distances that trigger open or close events.
PAGE 6
Local diagnostics test About this task: After power-up or closing the cover, the device automatically enters Test Mode for 15 minutes. To manually enter the devices into Test Mode refer to the Control Panel Installer Guide. 1. Before you start the test, remove the device cover from the base. See Figure 4. 2. Close the cover to return the tamper switch to its normal position. 3. Momentarily open the door or window and verify the red LED blinks, indicating detection.
PAGE 7
Compliance with standards MC-303 PG+ complies with the following standards: MC-303 P9M0 FCC (915 MHz): 47CFR part 15.247 FCC Compliance Statement This device complies with FCC Rules Part 15 license-exempt standard(s). Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation.
PAGE 8
About MC-303 PG+ The MC-303 PG+ is a thin, ultra-long-life PowerG magnetic contact device that is compatible with Johnson Controls’ PowerG control panels. The MC-303 PG+ includes a built-in reed switch that opens a circuit when the magnet is moved from its usual position.
PAGE 9
• damage arising out of any other abuse, mishandling or improper application of the Products.
PAGE 10
Email: info@visonic.com Website: www.visonic.com D-308437 Rev. 0 (01/22) ©2022 Johnson Controls. All rights reserved. JOHNSON CONTROLS, TYCO and VISONIC are trademarks and/or registered trademarks. Unauthorized use is strictly prohibited. D-308437 MC-303 PG+ Rev.