User's Manual

ManualsBrandsVisonic ManualsElectronicsWireless Digital Pet Immune PIR Detector

Table Of Contents

D-306133 MP-802 K9-85 PG2 Installation Instructions 1

1. INTRODUCTION

The MP-802 K9-85 PG2 (pet immune) is a microprocessor-controlled wireless digital PIR detector

supported by the PowerMaster alarm system using PowerG two-way communication protocol.

The detector's features are as follows:

l Fresnel and cylindrical lenses with uniform detection sensitivity throughout its operating range, up to 12

meters (39 ft).

l Target Specific Imaging™ (TSI) technology is used for distinction between humans and pets weighing

up to 38 kg (85lb).

l The advanced True Motion Recognition™ algorithm (patented) allows distinguishing between the true

motion of an intruder and any other disturbances which may cause false alarms.

l No vertical adjustment is needed.

l Motion event counter determines whether 1 or 2 consecutive motion events trigger an alarm.

l Very low current consumption.

l Microprocessor-controlled temperature compensation. Sealed black chamber provides white light

protection.

l Front and back tamper protection.

l The device supports temperature and light level reports according to the PowerG panel.

For UL installations: The detector is for use with UL listed control unit only. Pet immunity has not been

evaluated by UL.

............. ........Figure 2 - Internal View

Figure 1: MP-802 K9-85 PG2

A. Enroll button

B. Light sensor

C. LEDs

D. Tamper switch

E. PIR sensor

MP-802 K9-85 PG2

Wireless Digital Pet Immune PIR Detector

Installation Instructions

Summary of content (7 pages)

PAGE 1
MP-802 K9-85 PG2 Wireless Digital Pet Immune PIR Detector Installation Instructions 1. INTRODUCTION The MP-802 K9-85 PG2 (pet immune) is a microprocessor-controlled wireless digital PIR detector supported by the PowerMaster alarm system using PowerG two-way communication protocol. The detector's features are as follows: l l l l l l l l l Fresnel and cylindrical lenses with uniform detection sensitivity throughout its operating range, up to 12 meters (39 ft).
PAGE 2
. INSTALLATION 2.1. General Guidance 1. Keep away from heat sources. 2. Do not expose to air drafts. 3. Do not install outdoors. 4. Avoid direct sunshine. 5. Do not install near high-voltage electrical line. 6. Do not install behind partitions. 7. Mount on solid stable surface. Warning! Do not obscure partially or completely the detector's field of view. Figure 3 - General Guidelines 2.2.
PAGE 3
2.3. Removing the Pet Mask Remove the plastic (pet mask) if you do not require pet immunity. Figure 10 - Removing the Pet Mask 1. Place your thumb at the base of the Pet Mask. 2. Place your fingers at the top of the Pet Mask. 3. Lift the Pet Mask to remove. 2.4. Disassembly from Bracket Figure 11 - Disassembly from Bracket 1. Release screw. 2. Separate the cover from the base. 3. Remove battery. 4. Press on the stopper snap to release the base from the bracket. 5. Slide the base downward to remove. 2.5.
PAGE 4
3 Select “ADD NEW DEVICES” Option – See Note [1] Enroll the device or enter the device ID ENROLL NOW or ENTR ID:XXX-XXXX Z14:Motion Sens (with panels PowerG V19.2 and lower) 4 Select the desired Zone Number ID No. 120-XXXX (with panels PowerG V19.2 and lower) Z14:S.Motion (with panels PowerG V19.3 and higher) ID No. 126-XXXX (with panels PowerG V19.
PAGE 5
LED response Green LED blinks Orange LED blinks Red LED blinks No blinks Reception Strong Good Poor No communication Important! Instruct the user to walk test at least once a week to verify proper function of the detector. Important! Reliable reception must be assured. Therefore, poor signal strength is not acceptable.
PAGE 6
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 7
ELECTRICAL Power Supply Internal Battery Nominal Battery Capacity Battery Life (typical use) Low Battery Threshold Note: Battery Power Test Type C. 3V Lithium battery, type CR-123A. For UL installations, use Panasonic and GP only 1450 mAh 6 to 8 years 2.4 V Inability to connect with wireless network, or wireless link quality no higher than 20% may significantly reduce the expected battery life Performed immediately upon battery insertion and periodically after every several hours.