User's Manual

ManualsBrandsVisonic ManualsElectronicsPIR detector

D-306082 MP-840 PIR ZB 1

MP-840

ZigBee Home Automation 1.2

Wireless Digital Pet Immune PIR Detector

Installation Instructions

1. INTRODUCTION

The MP-840 (pet immune) is a microprocessor-controlled wireless digital PIR detector supported by H.A 1.2

panels using ZigBee Home Automation.

The detector’s features are as follows:

• Fresnel and cylindrical lenses with uniform detection sensitivity throughout its operating range, up to 12

meters (39 ft).

• Target Specific Imaging™ (TSI) technology is used for distinction between humans and pets weighing

up to 38 kg (85lb).

• The advanced True Motion Recognition™ algorithm (patented) allows distinguishing between the true

motion of an intruder and any other disturbances which may cause false alarms.

• No vertical adjustment is needed.

• An on-board motion event jumper determines whether 1 or 2 consecutive motion events trigger an

alarm.

• After detection, the detector disarms itself to save battery power. It rearms (reverts to the ready state) if

there is no subsequent detection throughout the following 2-minute period.

• Very low current consumption.

• Microprocessor-controlled temperature compensation.

• White light protection.

• Front and back tamper protection.

• Elegantly styled, sturdy case.

• The device support on temperature’s report according to HA1.2’s panel.

For UL installations: The detector is for use with UL listed control unit only. Pet immunity has not been

evaluated by UL.

Figure 1: MP-840

2. SPECIFICATIONS

Detector Type

Dual element low

noise pyroelectric sensor

OPTICAL

Lens Data

Max. Coverage

Pet Immunity (pet version)

27 Fresnel “far” lenses (54 sensitivity “beams”)

18 cylinder “mid” curtain lenses (36 sensitivity “curtains”)

10 cylinder “close” curtain lenses (20 sensitivity “creep curtains”)

12 x 12 m, (39 x 39 ft) / 90°

Up to 38 kg (85 lb)

ELECTRICAL

Internal Battery

3V Lithium battery, type CR

123A. For UL installations, use

Panasonic

and GP only

Nominal Battery Capacity

1450 mAh

Battery Life (with LED on)

Battery Power Test

FUNCTIONAL

Typically over 5 years

Note: Inability to connect with wireless network, or wireless link quality no higher than 20% may

significantly reduce the expected battery life.

Performed immediately upon battery insertion and periodically after every several hours

True Motion Event

Verification

2 position selector - 1 (OFF) or 2 (ON) motion events

Alarm Period

2 seconds

LED Switch

LED Enable (red LED lights for 2 sec. upon Alarm detection)

LED Disable: No indication. (LED is always enabled during Walk-Test mode)

Rearm Timer

Rearms the detector 2 minutes after the last alarm. Timer disabled in the walk test mode

Summary of content (8 pages)

PAGE 1
MP-840 ZigBee Home Automation 1.2 Wireless Digital Pet Immune PIR Detector Installation Instructions 1. INTRODUCTION The MP-840 (pet immune) is a microprocessor-controlled wireless digital PIR detector supported by H.A 1.2 panels using ZigBee Home Automation. The detector’s features are as follows: • Fresnel and cylindrical lenses with uniform detection sensitivity throughout its operating range, up to 12 meters (39 ft).
PAGE 2
WIRELESS Supported Network Frequency Tamper Alert ZigBee H.A 1.2 2.405 – 2.480 Ghz as per IEEE 802.15.4 Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored MOUNTING Height Installation Options 1.8-2.4 m (6 - 8 ft). For pet rejection, the optimal height is 2.
PAGE 3
.2 Installation Procedure Figure 3 – Bracket Mounting Figure 5b – Battery Activation Figure 4 – Opening the Unit Figure 5a – Battery Insertion Figure 6 – Replacing Cover Figure 8 – Mounting Detector on Bracket Figure 7 – Securing with Screw 1. 2. 3. 4. 5. 6. 7. Mount the bracket on the wall Press in the point marked “F” in the drawing and separate the cover from the base Insert the battery while observing polarity.
PAGE 4
3.3 Removing the Pet Mask Remove the plastic (pet mask) in case of no need for pet immunity 1. Place your thumb at the base of the Pet Mask. 2. Place your fingers at the top of the Pet Mask.. 3. Lift the Pet Mask to remove. Figure 9 – Removing the Pet Mask 3.4 Disassembly from Bracket 1. Release screw (optional). 2. Separate the cover from the base. 3. Remove battery. 4. Press on the stopper snap to release the base from the bracket. 5. Slide the base downward to remove.
PAGE 5
3.5 Activating and Pairing the Detector To pair the detector to the control panel, you must set it to pairing mode. 1. First set the panel to pairing mode and then the detector. 2. To activate, pull the activation strip that protrudes from the back of the detector (see Figure 5). The device power-up stabilization procedure begins. 3 The red LED blinks every 5 seconds followed by the green LED which blinks 3 times to indicate that the detector is searching for a control panel.
PAGE 6
3.9 Walk Testing Walk-test the coverage area (see Figure 11) by walking across the far end of the coverage pattern in both directions. The red LED lights each time your motion is detected followed by steady LED signal strength indication. LED response Reception 3 Green LED blinks Green LED blinks once Orange LED blinks once Red LED blinks once No blinks No network Strong Good Poor No communication Important! Instruct the user to walk test at least once a week to verify proper function of the detector.
PAGE 7
4. COMPLIANCE WITH STANDARDS The MP-840 complies with the following standards: Europe : EN 300328, EN 301489, EN 60950-1, EN 50130-4, EN 50131-1, EN 50131-2-2 Grade 2 Class II. The MP-840 is compatible with the RTTE requirements - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 USA: FCC-CFR 47 Part 15, UL- UL 639 Canada: IC-RSS 247, ULC – S306 This device complies with Part 15 of the FCC Rules and RSS-247 of Industry and Science Canada.
PAGE 8
W.E.E.E. Product Recycling Declaration For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment. EMAIL: info@visonic.com INTERNET: www.visonic.com VISONIC LTD.