User's Manual

ManualsBrandsVisonic ManualsElectronicsPIR detector with ZigBee protocol

D-306094 XHS1-TY / MP-841 FLAT PIR COMCAST 1

XHS1-TY / MP-841

ZigBee Home Automation 1.2

Wireless Digital Pet Immune PIR Detector

Installation Instructions

1. INTRODUCTION

The XHS1-TY or MP-841 (pet immune) is a microprocessor-controlled wireless digital PIR detector supported by ZigBee HA 1.2.

The detector’s features are as follows :

• Up to 15 meters (49.2 ft)

• Uniform Detection

• White light immunity (Black mirror technology)

• Enhanced Pet immunity up to 85Ibs (Target Specific Imaging™ (TSI) technology (patented)

• Enhanced false alarm rejection (The advanced True Motion Recognition™ algorithm (patented)

• No vertical adjustment is needed.

• In normal mode, after detection, the detector goes to sleep to save battery power. It wakes again (reverts to the ready state) if there is no

subsequent detection throughout the following 2-minute period.

• Temperature compensation.

• Front and back tamper protection.

• Black mirror technology provides excellent white light protection.

• Elegantly styled, sturdy case.

Figure 1 - MP-841

A. Red LED

B. Green LED

C. Tamper Switch

Summary of content (6 pages)

PAGE 1
XHS1-TY / MP-841 ZigBee Home Automation 1.2 Wireless Digital Pet Immune PIR Detector Installation Instructions 1. INTRODUCTION The XHS1-TY or MP-841 (pet immune) is a microprocessor-controlled wireless digital PIR detector supported by ZigBee HA 1.2. The detector’s features are as follows : • • • • • • • • • • • Up to 15 meters (49.
PAGE 2
. SPECIFICATIONS Detector Type Optical Data Max. Coverage Pet Immunity Dual element low-noise pyroelectric sensor 27 “far” parabolic black mirrors (54 “beams”) 9 “near” cylinder black mirrors (18 "curtains”) Pet immune protection is provided by a specific optical attenuator on the mirror 15 x 15 m, (49.2 x 49.2 ft) / 90° Up to 38 kg (85 lb) ELECTRICAL Internal Batteries Nominal Battery Capacity Battery Life (with LED on) Two 3V Lithium batteries, type CR-123A.
PAGE 3
. INSTALLATION 3.1 General Guidance 1. Keep away from heat sources. 2. Do not expose to air drafts. 3. Do not install outdoors. 4. Avoid direct sunshine. 5. Keep wiring away from power cables. 6. Do not install behind partitions. 7. Mount on solid stable surface. Figure 2. General Guidelines 3.
PAGE 4
1. 2. 3. 4. Press in this point. Push in the direction of the arrow shown in the drawing to separate the detector from the bracket. Mount the bracket on the wall. Install new batteries. A. Use A1 or A2 for corner mounting B. Use for surface mounting C. Activation strip -ORIf batteries are already installed, pull the activation strip. 5. Mount the detector on the bracket by sliding it downward until a click is heard.
PAGE 5
3.6 Defaulting the Detector CAUTION! The defaulting process removes the device from the network and enables re-pairing. Separate the detector from the bracket to remove both batteries. (see Figure 7). 1. Press and hold down the detector’s tamper switch. 2. Insert one of the two batteries into the detector while observing battery polarity. 3. Release the tamper switch within 4 seconds (the LED blinks 3 times every 5 seconds). 4. To re-pair the detector, follow the instructions in section 3.4. 3.
PAGE 6
SPECIAL COMMENTS Even the most sophisticated detectors can sometimes be defeated or may fail to warn due to: DC power failure / improper connection, malicious masking of the lens, tampering with the optical system, decreased sensitivity in ambient temperatures close to that of the human body and unexpected failure of a component part. The above list includes the most common reasons for failure to detect intrusion, but is by no means comprehensive.