Installation Instructions

ManualsBrandsVisonic ManualsElectronicsPowerG Wireless Digital PIR Detector

D-302413 NEXT PG2, NEXT K9-85 PG2 Installation Instructions 1

NEXT PG2

NEXT PG2NEXT PG2

NEXT PG2

/ /

NEXTNEXT

K9K9

K9-

-85

8585

PG2

PG2PG2

PG2

PowerG, Wireless, PIR /Pet Tolerant Motion Detector

Installation Instructions

1. INTRODUCTION

1. INTRODUCTION1. INTRODUCTION

1. INTRODUCTION

The Next PG2 and Next K9-85 PG2 are 2-way, microprocessor-controlled, wireless digital PIR detectors.

The detectors features are as follows:

• For use with all PowerMaster® control panels (version 10 and higher).

• Combined Fresnel and cylindrical optics, up to 15 meters (49 ft).

• The Next PG2 includes wall creep zone protection.

• In Next PG2 and Next K9-85 PG2, Target Specific Imaging™ (TSI) technology is used for distinction

between human beings and pets weighing up to 38 kg (85lb).

• Includes a fully supervised PowerG transceiver.

• The advanced True Motion Recognition™ algorithm (patented) allows distinguishing between the true

motion of an intruder and any other disturbances which may cause false alarms.

• Sophisticated frequency domain digital signal processing.

• Built-in link quality indicators; no need for the installer to physically approach the control panel thus making

installation faster and easier.

A. LED

B. Lens

Figure 1: External View

• No vertical adjustment is needed.

• Motion event counter determines whether 1 or 2 consecutive motion events will trigger an alarm.

• Automatic termination of walk-test after 15 minutes.

• Microprocessor-controlled temperature compensation.

• Sealed chamber protects the optical system.

• Front cover and back tamper switches, for improved tamper protection.

• White light protection.

• Notes: 1. The pet immunity feature was not evaluated by UL.

2. For CE installations, the pet immunity was not evaluated by DNV.

3. The pet immunity feature is not evaluated and certified by Applica Test & Certification AS.

. .

. INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION

2.1 General Guidance (see Fig. 2)

1. Keep away from heat sources.

2. Do not expose to air drafts.

3. Do not install outdoors.

4. Avoid direct sunshine.

5. Keep wiring away from power cables.

6. Do not install behind partitions.

7. Mount on solid stable surface.

8. Installed in accordance with NEC, NFPA 70.

9. Installed in accordance with UL 681, Standard for

Installations and Classifications of burglar and Holdup

Alarm Systems.

1 2 3

4 5 6

Figure 2. General Guidelines

Important! The Next K9-85 PG2 detector is tolerant to 38 kg (85 lb) animals moving on the floor or climbing on

furniture as long as the activity takes place below 1 m (3 ft). Above the 1 m (3 ft) height limit, the detector is tolerant

to 19 kg (42 lb) pets, but the pet immunity will decrease as the pet gets closer to the detector. It is therefore

recommended to select a mounting location that minimizes potential close proximity of animals.

WARNING! To comply with FCC and IC RF exposure compliance requirements, the PIR detector should be located at a distance of at least 20

cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other

antenna or transmitter

Summary of content (4 pages)

PAGE 1
NEXT PG2 / NEXT K9K9-85 PG2 Installation Instructions PowerG, Wireless, PIR /Pet Tolerant Motion Detector 1. INTRODUCTION The Next PG2 and Next K9-85 PG2 are 2-way, microprocessor-controlled, wireless digital PIR detectors. The detectors features are as follows: • For use with all PowerMaster® control panels (version 10 and higher). • Combined Fresnel and cylindrical optics, up to 15 meters (49 ft). • The Next PG2 includes wall creep zone protection.
PAGE 2
.2 Mounting (see Fig. 3) Notes: 1. Mount the detector so that its orientation is perpendicular to the expected intrusion path. 2. For installations of detector at 2m high, Dead zone is 2ft at 0m high and 0.5ft at 1.5m high. 2 4 3 A B 1 C 1. Release screw and remove cover. 2. Push catch and remove board. 3. Insert battery. 4. Mounting D A. Front Tamper switch B. Back Tamper switch. C. On surface D. In corner Caution! Risk of explosion if battery is replaced by an incorrect type.
PAGE 3
. LOCAL DIAGNOSTICS TEST NOTE: Run a diagnostic test at least once a year to ensure that the detector is working correctly. A. Separate the base from the cover (see Fig. 3). B. Put back the cover to return the tamper switch to its normal (undisturbed) position, and then secure the front cover to the base with the case closure screw. C. The Next PG2 / Next K9-85 PG2 will enter a 2 min. stability period. During this time the red LED blinks. D. Walk-test the coverage area - see Fig. 5.
PAGE 4
WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with FCC Rules Part 15 and with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation.