User Manual

ManualsBrandsVisonic ManualsCamera & PhotoWireless digital PIR detector with camera

D-302893 1

NEXT CAM PG2,

NEXT CAM-K9 PG2

Wireless, PowerG, PIR / Pet Immune Detectors with

Integrated Camera

Installation Instructions

1. INTRODUCTION

The Next CAM PG2 is a 2-way, microprocessor-controlled,

wireless digital PIR detector with integrated camera and

microphone for alarm verification.

The PIR detector's features are as follows:

 Combined Fresnel and cylindrical optics, up to 12 meters (40 ft).

 The Next CAM PG2 includes wall creep zone protection.

 For pet immune version - Target Specific Imaging™ (TSI)

technology is used for distinction between human beings and

pets weighing up to 38 kg (85lb).

 Includes a fully supervised PowerG transceiver.

 The advanced True Motion Recognition™ algorithm (patented)

allows distinguishing between the true motion of an intruder and

any other disturbances which may cause false alarms.

 No vertical adjustment is needed.

 Motion event counter determines whether 1 or 2 consecutive

motion events will trigger an alarm.

 Automatic termination of walk-test after 15 minutes.

 Microprocessor-controlled temperature compensation.

 Sealed chamber protects the optical system.

 Front cover and back tamper, for improved tamper protection.

 White light protection.

 Battery compartment

The camera's features are as follows:

 Day and night CMOS camera, with IR illumination. This allows

taking pictures in full darkness without letting the intruder know.

 Camera range: 12 m (40ft). With IR illumination 10m (33 ft).

 Picture format and resolution: JPEG, QVGA (320x240 pixels).

 Frame rate: up to 3 fps (for user).

 Audio format: ADPCM, 4bit / 2bit.

 Camera operation modes:

o Post alarm – pictures are taken after detection by

detector.

o On demand – pictures are taken after a command from

the monitoring station.

A. Microphone

B. Camera lens

C. IR LED

D. Light sensor

LEDs

Fig. 1. External View

2. SPECIFICATIONS

GENERAL

Detector Type: Dual element low-noise pyroelectric sensor

Lens Data: No. of Curtain Beams / curtains:

Next CAM PG2: 18 far, 18 mid, 10 close.

Next CAM-K9 PG2: 18 far, 18 mid, 18 close.

Max. Coverage: 12 x 12 m, (40 x 40 ft) / 90°

Pet Immunity (Next CAM-K9 PG2 only): Up to 38 kg (85 lb).

ELECTRICAL

Internal Battery

6V Lithium battery (two CR-123A 3V batteries

or two CR17450 3V batteries, in series) or equivalent.

Note: For UL installations use Panasonic, Sanyo, GP or Varta

only. Use only the above battery. Dispose of used battery

according to the manufacturer's instructions.

Nominal Battery Capacity: 6V 1450 mA/h (2xCR123A), 2200

mA/h (2xCR17450)

Battery Life (for typical use): 3 or 5 years depending on battery

pack type (and camera version)

Optional MAINS supply:

Additional to batteries, 7.5 V DC.

Power Supply:

Type C

FUNCTIONAL

True Motion Event Verification

: 2 remote selections - 1 (OFF)

or 2 (ON) motion events

Alarm Period: 2 seconds

36 12 m0

10 20 30 40 ft

3 (10ft)

6 (20ft)

9 (30ft)

3 (10ft)

6 (20ft)

9 (30ft)

90°

3 6 9 12 m0

2.4 m

(8 ft)

10 20 30 40 ft

TOP VIEW

SIDE VIEW

Next CAM PG2: 0.5-4m, Next CAM -K9 PG2: 2-4m

Fig. 2. Coverage Pattern & Walk-test

Summary of content (6 pages)

PAGE 1
NEXT CAM PG2, NEXT CAM-K9 PG2 Installation Instructions Wireless, PowerG, PIR / Pet Immune Detectors with Integrated Camera 1. INTRODUCTION The Next CAM PG2 is a 2-way, microprocessor-controlled, wireless digital PIR detector with integrated camera and microphone for alarm verification. The PIR detector's features are as follows:  Combined Fresnel and cylindrical optics, up to 12 meters (40 ft).  The Next CAM PG2 includes wall creep zone protection.
PAGE 2
WIRELESS Frequency Band (MHz): Europe: 433, 868, USA: 915 Modulation: GFSK Antenna: Built-in helical antenna Communication Protocol: PowerG Supervision: Signaling at 4-min. intervals Tamper Alert: Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored MOUNTING Height: 1.8 - 2.4 m (6 - 8 ft). For Next CAM-K9 PG2, the recommended height is up to 2.
PAGE 3
14. NOT connected  Select between "NOT connected" and "Connected to AC". or 15. 16. AC POWER CONNECT 17. Here you determine whether the image will be in black & white or color. IMAGE COLOR 18. Black & White  Select between "Black & White" and "Color". or 19. 20. IMAGE COLOR 21. IMAGE RESOLUTION Here you set the pixel quality of the image. Select 160 x 120 for lower quality or 320 x 240 for higher quality. 22. Resol. 160 x120 Select between "Resol. 160 x 120" and "Resol. 320 x 240". or 23.
PAGE 4
5. LOCAL DIAGNOSTICS TEST A. Separate the base from the cover (see Fig. 5). B. Put back the cover to return the tamper switch to its normal (undisturbed) position, and then secure the front cover to the base with the case closure screw. C. Walk-test the coverage area - see fig. 2. Walk across the far end of coverage pattern in both directions, The red LED lights each time your motion is detected followed by 3 LED blinks. The following table indicates received signal strength indication.
PAGE 5
B 4 6 C 7 F D G E *CAUTION! THE BACK TAMPER SWITCH WILL NOT PROTECT THE UNIT UNLESS THE BREAK-AWAY BASE SEGMENT IS SECURED TO THE WALL WITH AT LEAST ONE SCREW. Figure 5a. Mounting on Wall 8 9 Figure 5b. Final Closure D-302893 1. Release screw. 2. Remove cover from base. 3. Position the battery in the battery holder and insert the battery connector terminal into the battery connector. 4. For optional mains power supply: Break the cable entry knockout and insert the mains cable. 5.
PAGE 6
7. SPECIAL COMMENTS Even the most sophisticated detectors can sometimes be defeated or may fail to warn due to: DC power failure / improper connection, malicious masking of the lens, tampering with the optical system, decreased sensitivity in ambient temperatures close to that of the human body and unexpected failure of a component part. The above list includes the most common reasons for failure to detect intrusion, but is by no means comprehensive.