Specifications
D-300885 19
4.5 DEFINING COMMUNICATION PARAMETERS
Preliminary Guidance
This mode allows you to adapt the telephone
communication parameters to the local requirements.
Compatible central station receivers are:
Osborne-Hoffman model 2000, Ademco Model 685,
FBII Model CP220, Radionics Model D6500, Sur-Gard
Model SG-MLR2-DG and Silent Knight Model 9500.
IMPORTANT: In telephone / pager number locations and
account number locations, you may be required to enter
hexadecimal digits. In telephone number locations, these
digits are used as codes to control the dialer:
Hex.
Digit
Keying
Sequence
Code
Significance
A <#>
⇒
<0>
Applicable only
at the beginning of a
number - the dialer waits 10 seconds
or waits for dial tone, whichever
comes first and then dials.
B <#>
⇒
<1> Inserts an asterisk (J)
C <#>
⇒
<2> Inserts a pound sign (#)
D <#>
⇒
<3>
Applicable only
at the beginning of a
number - the dialer waits 5 seconds
for dial tone and goes on hook if none
is received.
E <#>
⇒
<4>
A
pplicable only in the middle of the
number - the dialer waits 5 seconds
F <#>
⇒
<5> Not applicable in phone numbers
To enter a series of digits, use the following keys:
<Numeric keypad> - to enter the number
- moves the cursor from left to right
- moves the cursor from right to left
- deletes everything after the cursor (to the right).
4.5.1 Autotest Time
(Fig. 4.5, location 01). Here you determine the time at which
the telephone line will be tested and reported to the central
station.
4.5.2 Autotest Cycle
(Fig. 4.5, location 02). Here you determine the time interval
between consecutive telephone line test messages sent to
the central station. The control panel performs this at
regular intervals to verify proper communications.
The options are: test every 1, 5, 7, 14, 30 days and test off.
4.5.3 Area Code
(Fig. 4.5, location 03). Here you enter the system tel. area
code (up to 4 digits).
4.5.4 Out Access No
(Fig. 4.5, location 04). Here you enter the number that is used
as a prefix to access an outside telephone line (if exists).
4.5.5 First Central Station Tel.
(Fig. 4.5, loc. 05). Here you program telephone number of the 1
st
central station (including area code, 16 digit max) to which
the system will report the event groups defined in memory
location 11 (see note in Fig. 4.5).
4.5.6 First Account No.
(Fig. 4.5, location 06). Here you enter number that will
identify your specific alarm control system to the first
central station. The number consists of 4 or 6 hexadecimal
digits (see note in Fig. 4.5).
4.5.7 2
ND
Central Station Tel
(Fig. 4.5, loc. 07).
Here you program telephone number of the
2
nd
central station (including area code, 16 digit max) to which
the system will report the event groups defined in memory
location 11 (see note in Fig. 4.5).
4.5.8 Second Account No.
(Fig. 4.5, loc. 08). Here you enter number that will identify
your system to the 2
nd
central station. The account number
consists of 4 or 6 hexadecimal digits (see note in Fig. 4.5).
4.5.9 Report Format
(Fig. 4.5, location 09). Here you select the reporting format
used by the control panel to report events to central stations
(see note in figure 4.5).
The options are: Contact-ID SIA 4/2 1900/1400
4/2 1800/2300 Scancom (see Appendix C - code lists).
4.5.10 4/2 Pulse Rate
(Fig. 4.5, location 10). Here you select the pulse rate at
which data will be sent to central stations if any one of the
4/2 formats has been selected in Location 09 REPORT
FORMAT (see note in Fig. 4.5). The options are: 10, 20,
33 and 40 pps.
4.5.11 Reporting to Central Stations
(Fig. 4.5, location 11) (see note in Fig. 4.5).
Here you determine which types of event will be reported
to central stations. Due to lack of space in the display,
abbreviations are used: alarm is “alrm”, alert is “alrt” and
open/close is “o/c”. The asterisk (J) is a separator
between events reported to central station 1 and events
reported to central station 2.
Messages are divided by type into three groups:
GROUP
EVENTS REPORTED
Alarms Fire, Burglary, Panic, Tamper
Open/Close Arming AWAY, Arming HOME, Disarming
Alerts No-activity, Emergency, Latchkey
"Alarm" group has the highest priority and "Alert" group
has the lowest priority.
The selectable options are as follows:
Plan name Sent to center
1
Sent to center 2
all -o/c J backup All but open/close
All but open/close if center 1
doesn’t respond
all J all All All
all-o/c J all -o/c All but open/close All but open/close
all –o/c J o/c All but open/close Open/close
all (–alrt) J alrt All but alerts Alerts
Alrm J all (–alrm) Alarms All but alarms
Disable report Nothing Nothing
all J backup All All if cent. 1 doesn’t respond
Note: “All” means that all 3 groups are reported and also
trouble messages - sensor / system low battery, sensor
inactivity, power failure, jamming, communication failure etc.
4.5.12 Report CNF Alarm
(Fig. 4.5, location 12). Here you determine whether the
system will report whenever 2 or more events (confirmed
alarm) occur during a specific period (see par. 4.4.33 and
note in figure 4.5).
Available
options are: enable report, disable report,
enable + bypass (enabling report and bypassing the
detector - applicable to PowerMaxComplete that is
compatible with DD423 standard).
4.5.13 Send 2WV Code
(Fig. 4.5, location 13). Here you determine whether the
system will send two-way voice code to the central station
(to turn the central station from data communication to voice
communication state) by using pre-selected SIA or Contact-
ID communication format only (see note in Fig. 4.5).
Options: send and don't send.