Specifications
D-300885 21
(See note)
Note
The currently saved options
are displayed with dark box
at the right side of the display.
To review the options,
repeatedly click or
until the desired option
is displayed, then click OK (a
dark box will be displayed at
the right side).
22: PAGER TEL #
xxxxxxxxxxxxxxxx
(Enter Tel. No.)
23: PAGER PIN #
xxxxxxxxxxxxxxxx
(Enter PIN No.)
24: REPORT PAGER
all
alarm +alert
all (-op/cl)
trbl + op/cl
trbl
op/cl
disable report
13: SEND 2WV CODE
send
don’t send
(See note)
11: REPORT CNTR
all - o/c
*
backup
all
*
all
all - o/c
*
all - o/c
all - o/c
*
o/c
all (-alrt)
*
alrt
alrm
*
all (-alrm)
disable report
all
*
backup
(See note)
07: 2ND CNTR TEL
xxxxxxxxxxxxxxxx
(Enter Tel. No.)
(See note)
08: 2ND ACCOUNT #
xxxxxx
(Enter account No.)
(See note)
(See appendix - code list)
09:REPORT FORMAT
contact ID
SIA
4/2 1900/1400
4/2 1800/2300
Scancom
(See note)
10: 4/2 PLS RATE
10 pps
20 pps
33 pps
40 pps
(See note)
21: TEL ACKNWLDGE
single ack
all ack
20: REPORT PRVT
all
all (-op/cl)
all (-alerts)
alarms
alerts
op/cl
disable report
19: PRVT ATTEMPTS
1 attempt
2 attempts
3 attempts
4 attempts
18: VOICE PRVT
enable two-way
disable two-way
2 attempts
4 attempts
8 attempts
12 attempts
16 attempts
16: DIAL ATTEMPTS
(See note)
1 minute
3 minutes
5 minutes
10 minutes
15: RINGBACK TIME
(See note)
time out 10 s
time out 45 s
time out 60 s
time out 90 s
time out 2 m
ring back
disable
14: VOICE C.S.
(See note)
17: SET PRVT TEL#
1st private tel#
2nd private tel#
3rd private tel#
4th private tel#
xxxxxxxxxxxxxxxx
(Enter Tel. No.)
12: RPRT CNF ALRM
enable report
disable report
(See note)
enable + bypass
06: 1ST ACCOUNT #
xxxxxx
(Enter account No.)
(See note)
05: 1ST CNTR TEL
xxxxxxxxxxxxxxxx
(Enter Tel. No.)
(See note)
02:AUTOTST CYCLE
01: AUTOTEST TIME
Test time 12:00 P
(Enter test time)
03:AREA CODE 04: OUT ACCESS No
xxxx
(Enter tel. area
code, up to 4-digit)
x
(Enter ext. tel. line
access code, 1-digit)
25: RECENT CLOSE
recent cl. on
recent cl. off
27: MAST. DL CODE
26:REMOTE ACCESS
rem. access on
rem. access off
28: INST. DL CODE
30: ZONE RESTORE
report restore
don’t report
32: DIAL METHOD
tone (dtmf)
pulse
31: UPLOAD OPTION
when system OFF
any time
35: SYS INACT REP
disable
rep after 7d
34: UL/DL TEL #
rep after 14d
rep after 30d
rep after 90d
xxxxxxxxxxxxxxxx
(Enter Tel. No.)
33: LINE FAIL REP
don’t report
immediately
5 minutes
30 minutes
60 minutes
180 minutes
test every 1d
test every 5d
test every 7d
test every 14d
test every 30d
test OFF
xxxx
downl. code AAAA
(Enter 4-digit code)
(”0000” is not valid)
xxxx
downl. code BBBB
(Enter 4-digit code)
(”0000” is not valid)
4. DEFINE PANEL
5. DEFINE COMM.
<OK> TO EXIT
USER SETTINGS
ENTER CODE
1. NEW INSTL CODE
2. ENROLLING
3. DEFINE ZONES
INSTALLER MODE
[inst. code] (see
note
)
READY 00:00
NORMAL MODE
Note
For Control Panel that has
installer code
&
master
installer code
,
the following
functions are available only if
the MASTER INSTALLER
code is entered:
05: 1ST CNTR TEL
06: 1ST ACCOUNT #
07: 2ND CNTR TEL
08: 2ND ACCOUNT #
09: REPORT FORMAT
10: 4/2 PLS RATE
11: REPORT CNTR
12: RPRT CNF ALRM
13: SEND 2WV CODE
14: VOICE C.S.
15: RINGBACK TIME
16: DIAL ATTEMPTS
27: MAST. DL CODE
Not applicable
in the USA
38:AMBIENT LEVEL
Applicable for USA only
high
low
Figure 4.5 - DEFINE COMM Flow Chart