Installation Instructions

ManualsBrandsVisonic ManualsElectronicsAlarm System Control Panel

DE5465 1

POWERMAX+

Fully Supervised Wireless Alarm Control System

TABLE OF CONTENTS

1. INTRODUCTION........................................................ 2

2. SPECIFICATIONS ..................................................... 2

2.1 General Data....................................................... 2

2.2 RF Section .......................................................... 2

2.3 Electrical Data..................................................... 2

2.4 Communication ................................................... 3

2.5 Physical Properties ............................................. 3

3. INSTALLATION.......................................................... 3

3.1 Unpacking the Equipment .................................... 3

3.2 Supplying Power to the Unit................................. 3

3.3 Programming........................................................ 3

3.4 Mounting ............................................................. 3

3.5 Wiring ................................................................... 3

3.6 Connecting the AC Transformer .......................... 6

3.7 PowerMax+ Compatible Detectors....................... 6

3.8 PowerMax+ Compatible Transmitters.................. 6

3.9 PowerMax+ Compatible WL Siren ....................... 7

3.10 Installing an Optional X-10 Siren.......................... 7

3.11 Connecting PowerMax+ to a Computer ............... 7

3.12 Connecting PowerMax+ to GSM Modem............. 7

4. TESTING PROCEDURES .......................................... 7

4.1 Preparations ........................................................ 7

4.2 Diagnostic Test.................................................... 7

4.3 Keyfob Transmitter Test ...................................... 7

4.4 Appliance ON/OFF Test ...................................... 8

4.5 Emergency Transmitter Test ............................... 8

5. MAINTENANCE.......................................................... 8

5.1 Dismounting the Control Panel............................ 8

5.2 Replacing the Backup Battery ............................. 8

5.3 Fuse Replacement .............................................. 8

5.4 Replacing/Relocating Detectors .......................... 8

APPENDIX A. DETECTOR DEPLOYMENT AND

TRANSMITTER ASSIGNMENTS ............................... 9

A.1 Detector Deployment Plan .................................. 9

A.2 Keyfob Transmitter List ....................................... 9

A.3 Emergency Transmitter List .............................. 10

A.4 Non-Alarm Transmitter List ............................... 10

APPENDIX B. X-10 UNIT AND PGM OUTPUT

ASSIGNMENTS ........................................................ 10

FCC STATEMENTS ....................................................... 11

MESSAGE TO THE INSTALLER

The PowerMax+ control panel is supplied with 3 instruction manuals:

 Installation Instructions (this manual - for your exclusive use)

 Programming Guide (for your exclusive use)

 User’s Guide (for your use during installation only. Must be handed over to the master user after testing the system).

Appendices A and B of the installation instructions will help you prepare an installation plan. Please take time to fill out the

forms - your job will become much easier and confusion will be prevented. Filling out the forms will also help you create a

list of detectors and transmitters that must be obtained for the particular application. Compatible detectors and transmitters

are listed and described briefly in Paragraphs 3.7 and 3.8 of this manual.

Remember - it is advisable to power up the control panel temporarily after unpacking and program it on the work bench, in

accordance with the installation plan. Paragraph 3.3 of this manual refers you to the programming guide.

The programming flow charts in the programming guide show all options available for each parameter. Factory defaults are

marked with a dark box to their right, and other options (that can be selected instead) are marked by clear boxes. This

method allows you to put a checkmark in the appropriate clear box whenever you deviate from the factory defaults.

Although setting the correct time and date is one of the user tasks, we recommend that you set the time and date in the

course of programming. Access to the “User Settings” for the installer is possible through item 10 on the installer‘s menu or

through the user menu (see User’s manual section 7).

After programming, proceed to install the system as detailed in the Installation Instructions, from paragraph 3.4 onward.

WARNING! Zone type "emergency" can not be used for medical applications in UL-listed systems.

The installer should verify line seizure. Be aware of other phone line services such as DSL.

Summary of content (12 pages)

PAGE 1
POWERMAX+ Fully Supervised Wireless Alarm Control System Installation Instructions TABLE OF CONTENTS 1. INTRODUCTION ........................................................ 2 2. SPECIFICATIONS ..................................................... 2 2.1 General Data....................................................... 2 2.2 RF Section .......................................................... 2 2.3 Electrical Data ..................................................... 2 2.4 Communication ................
PAGE 2
1. INTRODUCTION The PowerMax+ is a user and installer-friendly, 30-zone fully-supervised wireless control system. The system is designed to function in a way that appeals to the user but also offers features that make installers’ life easier than ever before: EASY TO INSTALL • Plug-in terminal blocks can be wired while detached from the unit. • Quick attach-detach TELCO sockets for telephone line and X-10 controller. Terminal block for telephone line & set.
PAGE 3
Detector 1 & 2 Total (Sum) Current: 100* mA max. High Current / Short Circuit Protection: All outputs are protected (current limited). * Total PowerMax+ output current (of INT & EXT sirens, PGM output and detectors) cannot exceed 600 mA. Total INT & EXT sirens current consumption cannot exceed 550 mA. For UL installations, total output current cannot exceed 550 mA. Backup Battery (provides power for at least 24 hours), according to the purchase option: Option 1 (applicable for UL installations): 7.
PAGE 4
1 2 Open keypad cover 3 Release battery area cover 4 Remove battery area cover Remove bracket locking screw BATTERY AREA COVER SLOT Screw holes Special plastic washer Screw holes Special plastic washer 5 Push the bracket as shown and then remove it Mounting surface 6 Mark and drill 4 holes in mounting surface. Insert wall anchors and fasten the bracket to the mounting surface with 4 screws NOTE Verify that there is 3 cm (1.25 in.
PAGE 5
CONNECT WIRED DETECTORS AS FOLLOWS: Detector with Tamper switch Detector without Tamper switch TAMP Alarm N.C. N.C. Power Alarm N.C. - + 2.2 kΩ ZONE 29 / ZONE 30 Note Regarding zones 29 & 30, the PowrMax+ “sees” a specific resistance according to the event, as follows: Normal (no alarm & no tamper): 2.2 kΩ Alarm event: 4.4 kΩ Tamper event: Infinite resistance Power - + 2.
PAGE 6
3.6 Connecting the AC Transformer CAUTION! Do not plug the transformer into the AC outlet before completing all other wiring. A. U.S.A. only: Remove the center screw from the AC wall outlet. B. Plug the transformer directly in - the Power LED of the control panel should illuminate. C. U.S.A. only: Use the screw removed in Step A above to secure the transformer to the AC outlet. Tighten the screw well. D. The distance of the transformer from the system should not exceed 150 ft using 18 AWG conductors.
PAGE 7
C. MCT-134 / 104* (Fig. 13): (N.A. in North America) 4-button hand-held units. MCT134 (CodeSecure) can replace the MCT-234 keyfob. MCT-104 (PowerCode) can perform emergency and non- alarm functions. Both units look alike. Figure 13. MCT-134 / 104 D. MCT-132 / 102* (Fig. 14): (N.A. in North America) 2button units. MCT-132 (CodeSecure) can perform functions as shown. MCT102 (PowerCode) can perform emergency and non- Figure 14. MCT-132 / 102 alarm tasks. Both units look alike. E. MCT-131 / 101* (Fig. 15): (N.
PAGE 8
Press the keyfob unit’s DISARM ( ) key. The ARM indicator should extinguish, the announcement “Disarm, ready to arm" should be heard and the display should revert to: READY HH:MM Test the AUX button in each keyfob in accordance with the information noted in Table A.2, Appendix A. Verify that the AUX button performs its duty as programmed. If the AUX (@) button is defined as “STATUS”, system status should be displayed and announced upon pressing the button.
PAGE 9
APPENDIX A. Detector Deployment & Transmitter Assignments A1. Detector Deployment Plan Zone No. Zone Type Sensor Location or Transmitter Assignment (in non-alarm or emergency zones) Chime (Yes / No) Controls PGM Controls (X = YES) X-10 Unit No.
PAGE 10
A3. Emergency Transmitter List Tx # Transmitter Type Enrolled to Zone Name of holder 1 2 3 4 5 6 7 8 9 10 A4. Non-Alarm Transmitter List Tx # Transmitter Type Enrolled to Zone Name of holder Assignment 1 2 3 4 5 6 7 8 9 10 APPENDIX B. X-10 Unit and PGM Output Assignments Unit No. Controlled Appliance ON ON ON by arm by arm by HOME AWAY disarm ON by Memory ON ON by by Delay Keyfob ON by Timer ON OFF Time Time ON by Zone No.
PAGE 11
Federal Communications Commission (FCC) Statements FCC PART 15 STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 12
WARRANTY Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its products hereinafter referred to as "the Product" or "Products" to be in conformance with its own plans and specifications and to be free of defects in materials and workmanship under normal use and service for a period of twelve months from the date of shipment by the Manufacturer.