VPM8030 VPM8032 VPM8130 VPM8132 VPM8120 VPM8122 VPC9030 VPC9032 VPC9130 VPC9132 VPC9032/CM VPC9132/CM Protos 3 Series Cameras Installation Instructions Read these instructions first!
Installation Instructions INTRODUCTION Read all of these instructions. Use them to install your camera and have them available for its lifetime. If you have any problems, contact your agent. Note that not all cameras have all of the features described in this manual. Refer to the table below for the features of individual cameras. All cameras are fitted with a Direct Drive (DD) lens connector, an Auto Iris (AI) connector, have adjustable back focus and accept C and CS lenses.
Installation Instructions PRODUCT SAFETY Installation and servicing is only to be carried out by suitably qualified and experienced personnel. Mains cameras contain hazardous voltages. Do not remove covers as there is a risk of injury or death by electric shock. Cameras connected to mains supplies must be earthed. Only power low voltage cameras from a class 2 isolated power supply. This camera range is designed for use in general purpose CCTV applications and has no other purpose.
Installation Instructions CAUTIONS In order to avoid damaging the camera note the following points: 1) The camera has threaded mounting points on the top and bottom of the case. Only use a standard, photographic, mounting-bolt with a 1/4 20 UNC thread. 2) Before fitting the lens make sure that its back will not touch the CCD sensor or associated components when screwed fully home. 3) Do not touch the image-surface of the sensor. If the sensor is accidentally touched, only clean it using ethyl alcohol.
Installation Instructions CONTROLS AND SWITCHES On the side of the camera is a hinged flap. The hinged flap covers various adjustment controls and function switches. 5 1 2 3 4 LOW VOLTAGE MODELS (11a) (12) MONO CAMERAS (13) 6 7 1 2 3 4 (10) (8) (9) 230 VAC MODELS (12) COLOUR CAMERAS (11b) (13) Default switch positions shown (white represents switch position) (1) Synchronisation Selection (LL/INT) This switch is used to select the camera synchronisation mode.
Installation Instructions CONTROLS AND SWITCHES (4) Electronic Iris (EI) The Electronic Iris (EI) compensates for excessive light level by automatically adjusting the shutter speed. The electronic iris should be ON when using fixed or manual iris lenses. When using Auto Iris (AI) lenses of either the video drive or DC drive types the EI must be OFF. Also see (10) Electronic Iris and DC Lens Level Adjustment Potentiometer.
Installation Instructions CONTROLS AND SWITCHES output for a typical scene. The level should not be adjusted unless absolutely necessary. (11a) Supply Voltage Terminals This terminal accepts an 11-40 VDC or 14-30 VAC at 50Hz (CCIR/PAL) or 60Hz (EIA/NTSC) power source. Ther terminals are the quick release type. To connect a cable press the appropriate release lever and insert the end of the cable fully home. Ensure that there is sufficient length of bare tinned wire to make contact with the connector.
Installation Instructions LENS SELECTION VPC9132/CM VPC9132 VPC9130 VPC9032 VPC9030 VPM8122 VPM8120 VPM8132 VPM8130 VPM8032 VPM8030 Lens size VPC9032/CM Suitable lens types are C and CS mount in fixed iris, manual iris, auto iris or direct drive versions. Sizes are shown below. Cameras are factory set for CS mount lenses. If using a C mount lens, rotate either of the back focus screws approximately 30 turns anticlockwise before fitting the lens.
Installation Instructions FOCUS ADJUSTMENT Auto Iris and Direct Drive Lenses Fully open the iris by covering the lens with a suitable neutral density (ND) filter. Set the lens focus to infinity. View an image greater than 7 feet (2 meters) away. Focus the image using the back focus screw. Remove the ND filter and set the lens focus as required. Zoom Lenses Set the lens focus to infinity and fully open the iris by covering the lens with a suitable neutral density (ND) filter.
Installation Instructions 10
Installation Instructions 11
Norbain SDL Limited Norbain House, Eskdale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TS Norbain SDL Limited reserve the right to make changes to the product and specification of the product from time to time without prior notice HB-PROTOS3D-6 Issue 6 04/02
