User's Manual

ManualsBrandsVISTEON ELECTRONICS FRANCE ManualsElectronicsVehicle Interface

Page 1 of 10

WML-C30_User_Manual

25th Oct 2004

COMMERCIAL IN CONFIDENCE

This material may not in whole or part be copied, stored electronically or communicated to third parties

without MITSUMI ELECTRIC CO., LTD’s prior agreement in writing.

WML- 30## User Manual (system model: VI)

The purpose of this manual is to explain correct way how to integrate module WML- 30## to the end

product. It includes procedures that shall assist you to avoid unforeseen problems.

This manual presents information that shows how module and OEM product, where module integrated,

complies with regulations in certain regions. Any modifications, not expressly approved by the

manufacturer could void the authority to operate in these regions.

Content

1.General

2. Module design application.

3. Regulatory and Safety Compliance. European Union.

3.1 Declaration about performed tests.

3.2. Labelling

4. FCC Regulatory Information

4.1 Labelling.

4.2 Antenna implementation notes.

5. Other regulatory notes for OEM.

6. A separate approval.

1. General

This Bluetooth radio module has to be installed and used in accordance with the technical

description/installation instructions provided by the manufacturer.

This Bluetooth radio module is intended to be placed on the market in all States, where

the Bluetooth™ technology and the used frequency band is released.

For detail information concerning type approval of this module (e.g. where this module is

already pre-approved) please contact the authorised local distributor or the manufacturer.

The system may only be implemented in the configuration that was authorized.

Note that any changes or modifications to this equipment not expressly approved by

the manufacturer could void the user’s authority to operate this equipment.

Summary of content (10 pages)

PAGE 1
Page 1 of 10 WML-C30_User_Manual 25th Oct 2004 WML- 30## User Manual (system model: VI) The purpose of this manual is to explain correct way how to integrate module WML- 30## to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions.
PAGE 2
Page 2 of 10 WML-C30_User_Manual 25th Oct 2004 2. Module design application. 2.1 Model Number 1 # Contents N : without Antenna , A : with Antenna 2nd # B : BCSP , H : UART , U : USB Model number st WML-C30## 2.2 Hardware: Version 1 This document describes the reference design for application as follows. 2.3 FEATURES 1 ) Wireless communication module conforming to Bluetooth Ver.1.2. 2 ) Small and thin size achieved through use of high density mounting technology. WML-C30N# : 13.2 x 18.8 x 2.
PAGE 3
Page 3 of 10 WML-C30_User_Manual 25th Oct 2004 2.
PAGE 4
Page 4 of 10 WML-C30_User_Manual 25th Oct 2004 2.6 Software Stack for module and customer side example API RFCOMM/SDP Customer Stack L2CAP USB port driver UART port driver HCI USB port driver HCI UART port driver Module LMP Stack Link manager Baseband / RF COMMERCIAL IN CONFIDENCE This material may not in whole or part be copied, stored electronically or communicated to third parties without MITSUMI ELECTRIC CO., LTD’s prior agreement in writing.
PAGE 5
Page 5 of 10 WML-C30_User_Manual 25th Oct 2004 3. Regulatory and Safety Compliance . European Union. 3.1 Declaration about performed tests. The Mitsumi module WML-C30## is wireless data transmission system. This ‘Bluetooth’ module can be integrated into various end products. MITSUMI declares that The Mitsumi module WML-C30## complys with the following directive and standards: Directive 1999/5/EG (R&TTE Directive): EN 300328-2 V1.2.
PAGE 6
Page 6 of 10 WML-C30_User_Manual 25th Oct 2004 3.2 Labelling CE conformity marking for product. OEM product / application, where this radio module is integrated/ installed in , has to be labelled in accordance to R&TTE directive, Article 12. An auxiliary label is included in the packaging to the radio module, which can be used for that purpose and has to be permanently affixed to the OEM product/ application.
PAGE 7
Page 7 of 10 WML-C30_User_Manual 25th Oct 2004 4. FCC Regulatory Information The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 8
Page 8 of 10 WML-C30_User_Manual 25th Oct 2004 Module with antenna MITSUMI Company Logo Module’s Serial Number FCC Regulatory information. OEM devise should contain labelling that: Approved in accordance to FCC rules transmitter module marked by FCC-ID POOWML-C30XX label, manufactured by MITSUMI incorporated to OEM product. When its not possible, in user manual should be included such information. For example : “This device complies with Part 15 of the FCC Rules.
PAGE 9
Page 9 of 10 WML-C30_User_Manual 25th Oct 2004 All this labelling will be placed on the final product, clearly visible to all persons exposed to the transmitter. The specific location on the final product will be consistent with each same final product, but will vary in location across various final products, and in any case will always be clearly visible to all persons exposed to the transmitter.
PAGE 10
Page 10 of 10 WML-C30_User_Manual 25th Oct 2004 -Regarding FCC regulatory information on the FCC’s website at: www.fcc.gov/oet/info/database/letters/. - Regarding R&TTE directive http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm 6. A separate approval. A separate approval of the device into which the module is incorporated is only required when it cannot be insured that the conditions on the module grant will be met.