Installation Sheet

ASSEMBLY INSTRUCTIONS
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. ASSEMBLY THE FIXTURE (Fig.2)
1. Remove the parts carefully from the box.
2. Attach threading pipe Part K, Part H to part N on the frame. Tighten the
parts clockwise.
3. Pull the wire carefully in place. Attach part G to Part H. Tighten it clockwise.
4. Attach crystal straps Part F (4pcs, 8 straps), part I (14pcs, 16 straps, 1 strap
every 2holes), part L (8pcs, 16 straps, 1 strap every 2holes) to the lamp body
as drawing shows.
5. Attach ceiling chain to the loop, using quick link Part E.
Notes: for ceiling installation, please refer to the mounting and wiring
installation as below.
2. HANGING THE FIXTURE (Fig.1)
IMPORTANT: For a safe and secure installation, this fixture must be installed
by means of support that is independent of the outlet box.
1. Provide a 1/4” IPS pipe with one end securely mounted to a beam or a
structural member. The other end should protrude through the center of the
outlet box as shown.
2. Assemble the ceiling loop, nipple, nuts and hickey to center 1/4”IPS support
pipe and adjust overall length to allow the lock collar to hold the canopy flush
to the ceiling. When the adjustments have been completed, secure the three
(3) nuts, as shown.
3. Attach the chain to the fixture loop. Slip the lock collar and canopy over the
upper end of the chain. Open the end link of the chain and lift the fixture to
attach to the ceiling loop and secure the link.
4. Lace the fixture wires, ground and safety cable through the chain and loop,
exiting through the side of hickey. Run the safety cable through the top of the
outlet box and secure to structural member.
DRY
Paris Flea Market Large Chandelier
Item # CHC1408
CHC1408
ASSEMBLY & INSTALLATION GUIDE
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. ASSEMBLY THE FIXTURE (Fig.2)
1. Remove the parts carefully from the box.
2. Attach threading pipe Part K, Part H to part N on the frame. Tighten the parts clockwise.
3. Pull the wire carefully in place. Attach part G to Part H. Tighten it clockwise.
4. Attach crystal straps Part F (4pcs, 8 straps), part I (14pcs, 16 straps, 1 strap every 2holes), part L (8pcs, 16
straps, 1 strap every 2holes) to the lamp body as drawing shows.
5. Attach ceiling chain to the loop, using quick link Part E.
Notes: for ceiling installation, please refer to the mounting and wiring installation as below.
2. HANGING THE FIXTURE (Fig.1)
IMPORTANT: For a safe and secure installation, this fixture must be installed by means of support that is independent
of the outlet box.
1. Provide a 1/4” IPS pipe with one end securely mounted to a beam or a structural member. The other end should
protrude through the center of the outlet box as shown.
2. Assemble the ceiling loop, nipple, nuts and hickey to center 1/4”IPS support pipe and adjust overall length to
allow the lock collar to hold the canopy flush to the ceiling. When the adjustments have been completed, secure
the three (3) nuts, as shown.
3. Attach the chain to the fixture loop. Slip the lock collar and canopy over the upper end of the chain. Open the
end link of the chain and lift the fixture to attach to the ceiling loop and secure the link.
4. Lace the fixture wires, ground and safety cable through the chain and loop, exiting through the side of hickey.
Run the safety cable through the top of the outlet box and secure to structural member.
3. CONNECTING THE WIRES
1. At this point, connect the electrical wires as shown in Fig.3 making sure all wire nuts are secured. You May
have to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare
copper) connect fixture’s ground wire to it. Otherwise connect fixture’s ground wire directly to the junction box.
2. Tuck these wire connections neatly into the ceiling junction box.
3. Raise the lock collar and thread onto ceiling loop protruding through canopy.
Hex Nut
nut
crossbar
Lock collar
Nipple
Canopy
Ceiling loop
Chain(End Link)
Fixture Wires
Fixture
Ground Wire
FIG.1
FIG.2