Installation Sheet
.
WET
1. Carefully remove all parts from the carton.
2. Remove mounting plate (B) from fixture backplate (E) by removing side screws (F) in
counter-clockwise direction.
3. Put the mounting plate (B) on the wall J-box. Mark center points on the wall for four wood screws mounting
holes with a pencil. Remove mounting plate (B).
4. Drill small holes on each point location on the wall, each hole should be large enough to
accommodate to the plastic anchor (A). Push plastic anchors (A) into the holes in the wall.
5. Affix mounting plate (B) to wall outlet box, aligning holes and secure by inserting mounting
screws (D) to the holes of outlet box and screws (C) to the plastic anchors (A) in the wall.
6. Gently pull the wires from the wall outlet and allow the wires to hang. Feed the wires
through the center hole in mounting plate (B).
7. Open the fixture cap (L) by loosening door bolt (K).
8. Remove metal tabs (I) from inside of fixture backplate (E) by removing screws (H), insert glass
panels (G) to each frame of fixture backplate (E), secure with metal tabs (I) and screws (H).
9. Attach fixture steel safety cable to structural member in the wall. (Refer to the illustration)
10. Attach fixture ground wire (usully green) to ground wire of wall J-box (usually green or copper),
fasten together with a plastic wire connector. Tightly wrap the wire connector with electrical tape.
so the end of the connector is sealed. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR
HOME BE PROPERLY GROUNDED.
11. Connect fixture neutral wire (usully white ) to neutral wire (usually white ) of wall J-box. Fasten
the wires together with a plastic wire connector and tightly wrap the wire connector with
electrical tape.
12. Connect fixture hot wire (usully black ) to hot wire (usually black ) of wall J-box. Fasten the
wires together with a plastic wire connector and tightly wrap the wire connector with electrical tape.
Always make sure that no wire strands lreeft outside the connectors. DO NOT REVERSE THE HOT
AND NEUTRAL CONNECTIONS OTHERWISE SAFETY WILL BE COMPROMISED.
13. Attach fixture backplate (E) to mounting plate (B) and secure by side screws (F).
14. Insert light bulbs (not included) into sockets.
15. Close the fixture cap (L) and lock it with door bolt (K).
16. INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET LOCATION:
a. Mounting surface should be clean, dry, flat and 1/4" larger than canopy/fixture base on
all sides. Any gaps between the mounting surface and fixture base exceeding 3/16" should
be corrected as required.
b. With silicone (ex. GE-108) caulking compound, caulk completely around where back of
canopy/fixture base meets the wall surface to prevent water from seeping into outlet box.
TO AVOID WATER ENTERING THE FIXTURE BASE FROM THE SIDE OF FIXTURE, THIS
FIXTURE MUST BE MOUNTED ABOVE 1.2M (4 FT) FROM GROUND.
*** Clean with a dry, soft cloth only. Use no harsh abrasives or chemical agents.
ASSEMBLY INSTRUCTIONS
A
B
C
D
E
E
H
I
F
L
G
K
Elsinore Large Bracket Wall Sconce
Item # CHD 2953
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED
ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
5
16
"
(5
.
5mm)
7
32
"
(40mm)
11
16
"
(8m
m)
1
37
64
"
(17.5mm)