Installation Sheet
TOB 5016
ASSEMBLY & INSTALLATION GUIDE
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. Carefully unpack new fixture and lay all the parts on a clean surface.
2. Thread connection pole (F) into top threaded opening of part (G).
3. Thread connection pole (E) into pole (F).
4. Connect fixture wires to wires come from wall outlet. Remove back plate (A) from fixture base (B) by unscrewing
base screws (C).
5. Attach back plate (A) to ceiling outlet box and tighten with mounting screws (D).
6. Attach fixture base (B) to the affixed back plate (A) and insert base screws (C) to secure fixture base to the ceiling.
7. Remove clear protective plastic from shade (H).
8. Insert light bulbs into socket.
NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
9. Clip lamp shades (H) onto the light bulb.
CONNECTING THE WIRES:
1. At this point, connect the electrical wires as shown in the bottom Figure making sure all wire nuts are secured.
You May have to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper)
connect fixture’s ground wire to it. Otherwise connect fixture’s ground wire directly to the junction box.
2. Tuck these wire connections neatly into the ceiling junction box.
3. Raise the screw collar and thread onto screw collar loop protruding through canopy.
4. Insert light bulbs into sockets.
5. Your installation is now complete. Return power to the junction box and test the fixture.
1.
2.
3.
Fig.3
ASSEMBLY INSTRUCTION
Item No.: TOB5016
HANGING THE FIXTURE (Fig.1 )
1. Shut off the power at the circuit breaker and remove old
fixture from wall, including the old crossbar.
2. Carefully unpack new fixture and lay all the parts on a clean
surface.
3. Thread connection pole (F) into top threaded opening of
part (G).
4. Thread connection pole (E) into pole (F).
5. Connect fixture wires to wires come from wall outlet. (See
Fig.3)
6. Remove back plate (A) from fixture base (B) by unscrewing
base screws (C).
7. Attach back plate (A) to ceiling outlet box and tighten with
mounting screws (D).
8. Attach fixture base (B) to the affixed back plate (A) and
insert base screws (C) to secure fixture base to the ceiling.
CONNECTING THE WIRES (Fig.3)
1. At this point, connect the electrical wires as shown in Fig.3
making sure all wire nuts are secured. You May have to wrap
the connections with electrical tape. If your outlet has a ground
wire (green or bare copper) connect fixture’s ground wire to it.
Otherwise connect fixture’s ground wire directly to the junction
box.
2. Tuck these wire connections neatly into the ceiling junction box.
ASSEMBLE THE FIXTURE (Fig.2)
1. Remove clear protective plastic from shade (H).
2. Insert light bulbs Type C, maximum 40 watt into socket.
NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
3. Clip lamp shades (H) onto the light bulb.
Your installation is now complete. Return power to the
junction box and test the fixture.
(F)
(E)
(C)
(B)
(H)
ASSEMBLY INSTRUCTION
Item No.: TOB5016
HANGING THE FIXTURE (Fig.1 )
1. Shut off the power at the circuit breaker and remove old
fixture from wall, including the old crossbar.
2. Carefully unpack new fixture and lay all the parts on a clean
surface.
3. Thread connection pole (F) into top threaded opening of
part (G).
4. Thread connection pole (E) into pole (F).
5. Connect fixture wires to wires come from wall outlet. (See
Fig.3)
6. Remove back plate (A) from fixture base (B) by unscrewing
base screws (C).
7. Attach back plate (A) to ceiling outlet box and tighten with
mounting screws (D).
8. Attach fixture base (B) to the affixed back plate (A) and
insert base screws (C) to secure fixture base to the ceiling.
CONNECTING THE WIRES (Fig.3)
1. At this point, connect the electrical wires as shown in Fig.3
making sure all wire nuts are secured. You May have to wrap
the connections with electrical tape. If your outlet has a ground
wire (green or bare copper) connect fixture’s ground wire to it.
Otherwise connect fixture’s ground wire directly to the junction
box.
2. Tuck these wire connections neatly into the ceiling junction box.
ASSEMBLE THE FIXTURE (Fig.2)
1. Remove clear protective plastic from shade (H).
2. Insert light bulbs Type C, maximum 40 watt into socket.
NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
3. Clip lamp shades (H) onto the light bulb.
Your installation is now complete. Return power to the
junction box and test the fixture.
(F)
(E)
(C)
(B)
(H)