Instruction Manual

ManualsBrandsVISUAL LAND ManualsAudio EquipmentBluetooth headset

SAFETY INFORMATION

WARNING: Using earbuds at high volumes for extended periods of time will result in permanent hearing damage. It is advised you keep

volume levels moderate to low at all times for your safety. Turn the volume all the way down after connecting your earbuds, and then

gradually increase the volume until you reach a comfortable listening level. Do not use earbuds while driving a car, cycling, operating

machinery, or performing other activities that require hearing surrounding sounds.

Keep the device and packaging out of reach of children.

This device is designed and manufactured to operate within its defined design limits. Misuse may result in electric shock or fire. Read

and follow these instructions carefully.

 If submersed in water, do not turn the device on until completely dried. Note: liquid submersion voids the warranty.

 To prevent fire or shock hazards, do not expose this unit to rain or moisture. If the device comes in contact with liquids, quickly

wipe away. If submersed in water, do not turn the device on until completely dried. Note: liquid submersion voids the warranty.

 Danger of explosion or fire if batteries are damaged. Keep away from direct sunlight, naked flames, flammable gasses, or heat

sources such as radiators or stoves

 Do not use around flammable gasses as fire or explosion may occur.

 There are no user replaceable/reparable parts in the device. Disassembling it will void your warranty.

 Only use attachments/accessories specified by the manufacturer

Changes or modifications to this unit not expressly approved by Visual Land Inc. will void user’s Limited One Year Warranty.

COMPLIANCE INFORMATION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2)

FCC RULES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

 Relocate the receiving antenna.

 Increase the separation between equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help

PRODUCT OPERATION

1. Charging: Charge the earbuds by placing them into the charging case. Press the Wake/Sleep button

on the back of the case to view the remaining battery level of the charging case.

2. Power On: Flipping open the charging case automatically turns on the earbuds.

3. Power Off: Put the earbuds into the charging case and close the cover will automatically shut down

the earbuds and enter charging mode.

4. Bluetooth Pairing: Flip open the charging case, remove earbuds from the case and place earbuds

into ears, voice prompt will immediately announce “Power On”, “Pairing”, then finally “Device

Paired”. “Device Paired” signifies the Left and Right earbuds are paired; please note your earbuds

are not yet connected to your Bluetooth device. To connect to your Bluetooth device, on your

device’s Bluetooth settings, locate “SOUNDWAVE A1” from the list of available devices (this may

take several seconds). Tap “SOUNDWAVE A1” to connect, a voice prompt stating “Device

Connected” will be heard if pairing is successful. For future use, your device will remember the

earbuds, no need to pair again, just put on the earbuds and your device will automatically pair with

the earbuds. Only one device can be paired at a time. To pair another device to the earbuds, first

“Forget the Device” through your device’s Bluetooth settings (the device that is currently

connected), then repeat the pairing process.

5. Phone Call Mode: When the earbuds are on your ears and connected to your phone, press and hold

the left earbud for 2 seconds to active your device’s voice assistant.

a. When a call comes in: Single click on the left or right earbud to answer the call

b. During the call: Single click on the left or right earbud to hang up

c. To reject a call: Long press left or right earbud for 2 seconds

6. Smart Touch Control Functions

a. Answer (when there is an incoming call): Single click on the left or right earbud

b. Hang Up (during a call): Single click on the left or right earbud

c. Reject (incoming call): Long press any earbud

d. Sound Modes (Noise cancellation (ANC Mode)/ANC Off/Transparency Mode)

(standby/music): Long press on right earbud to cycle through the different modes.

e. Play/Pause (when music is playing): Singe click on left or right earbud

f. Decrease Volume (standby/play music): Double click the left earbud

g. Increase Volume (standby/play music): Double click the right earbud

h. Last song (when music is playing): Triple click on the left earbud

i. Next Song (when music playing): Triple click on the right earbud

j. Voice Assistant (Standby/Music): Long press the left earbud

k. Exit Voice Assistant: Long press the left earbud

l. Lower Battery Warning: A low battery warning tone will be reported every minute

when the battery is low

7. Voice Prompt Notifications

a. Pairing Mode: Pairing

b. Bluetooth Connected: Device Connected

c. Bluetooth Disconnected: Device Disconnected

d. Lower Power Prompt: “Beep”

e. Noise Cancellation On: ANC Mode

f. Noise Cancellation Off: ANC Off

g. Transparency Mode: Transparency Mode

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Label:

Summary of content (2 pages)

PAGE 1
PRODUCT OPERATION SAFETY INFORMATION WARNING: Using earbuds at high volumes for extended periods of time will result in permanent hearing damage. It is advised you keep volume levels moderate to low at all times for your safety. Turn the volume all the way down after connecting your earbuds, and then gradually increase the volume until you reach a comfortable listening level.
PAGE 2
LIMITED ONE (1) YEAR WARRANTY Following warranty service your Visuall Land Product or a replacement will be returned to you as your Visual Land Product was configured when originally purchased, subject to applicable updates. Visual Land may install system software updates as par part of warranty service that will prevent the Visual Land Product from reverting to an earlier version of the system software.