Operating instructions

utilization mode you Have selected.
This .rvice must be dedicated ar'td used
only to power your spa.
Four wire$ are to be pulled:
STEP 1.
2.
3.
STEP 2.
SYSTEM
JOA 50A
10 8
10 8
12 12
STEP 3.
Dual Circuit Breaker
2 Line voltage -Wire size No.
1 Ground -Wire Size No.
1 Neutral -Wire size No.
STEP 4,
STEP 5.
STEP 6.
4.
STEP 1.
STEP 8.
DO NOT PLUG in 120 volt PQWef' CQrd.
For -2.-40V AC system, make ~re breakers
are OFF.
Make aJre ALL electrical power to
equipment is in the OFF positioli.
Make sure thermostat is rotated to the
OFF position.
Make 9.lre the two 1~'. gate vaives
located at the Pump inlet and the heater
outlet are in the OPEN position. Lift
up on T handle. MAKE SURE ALL
JETS ARE OPEN (counter-clock wise}.
Make sure drain (hose-bib) valve Is
tight Iy closed.
Using garden hose, fill ~a with water
to 4" of top of spa -DO NOT permit
water line to drop below 5" from top
of spa at anytime.
Wait approximately 15 minutes and:
Inspect ~a water connections and
perimeter for any leaks or puddles of
water. If there are any leaks, call service
for repair If the leak cannot be readily
corrected, i.e.: connections, unions, etc.
5.
6.
In no case should smaller than 10 gauge
wire for 30A system or 8 gauge wire for
SOA system be used and only then when
the distance from the breaker box to the
equipment is less than 50 feet.
The power box is set-up to receive 314..
coOOuit and fittings.
Open power bOx. Make four wire
connections to power terminal strip as
per the inStructions on the box cover.
(SEE ILL BELOW) Make conversion
wiring changes as per the instructions
outlined in ..Heater Conversion
Instruction.', located in the back pocket
of this manual.
Ground equipment to a permanent earth
ground per applicable code.
ALL ELECTRICAL CONNECTION
MUST BE TO NEC (NATIONAL ELec-
TRIC CODE) AND TO ANY PERTINENT
LOCAL ELECTRIC CODE STAND-
ARDS.
7.
I LL. NO.4
12OV -1M -8»tZ
ELECTRICAL
SERVICE:
I L-. ZOA.12OV
N8Itr8 ~ 011-
0,..-
.
12/3 F* C.-
~-A1A-..Z
ELECTRICAL
SERVICE:
.100..
.'2
DUAL mA 8RUKIR
3.2 STARTING YOUR SPA
STEP 1. Plug power cord into 120 volt power
receptacle. Make sure breaker is ON
for 120 v or 240 v systems.
STEP 2. Press "T" test bUtton on GFCI and then
"R" r~t buttdn to operate. Reoiiew
section 1.3.2.
STEP 3. ox SERIES:
.Set timer for current time. select running
time and set timet selector switcfi t6 ON
position as explained in section 3.3.3.
.Close door. Spa will not function if the
door is open.
.Push selection button to function #1, low
speed pump. (See Section 3.3.1 )
LX SERIES: Press SYS button (SEE
SECTION 3.4 ..LX Feature and Func-
tions"). Light will come on. Press jet but~
ton. let jet operate for one minute mini-
mum. When the jets are noted to have
steady stream the system is ready. If
there is no jet flow after one minute, turn
system off and repeat start-up proce.
dure. (SECTION 3.2).
STEP 4. OX SERIES: You have just put the timer
selector switch to ON position. Low
speed pump will remain constantly on .
Set thermostat to desired setting. (See
section 3.3.2) Once spa has reached the
desired temperature, set timer selector
switch to center position for automatic
timer control. (See section 3.3.3)
LX SERIES: Press SYS button off .Turn
thermostat counter clockwise to desired
setting. Your spa will start to heat.
OPERATING INSTRUCTIONS
3.1 GeTTING YOUR SPA READY TO USE
With all electrical connections done you are
now ready to fill-up your Spa.
Pleese go through the following steps:
5