Replacement Part List

ManualsBrandsVITA ManualsArborsSierra 78.5 in. x 39 in. Composite Arbor

1. Post Caps (6) -

10600 White / 14066 Composite

2. Arches (4) - 10601 White / 14067 Composite

3. Arch Rafters (6)* - 10602 White / 14068 Composite

4. Side Panel Horizontal Top Rails (2) - 10603 White / 14072 Composite

5. Posts (2 L's & 2 R's)) - 10604-L & 10604-R White / 14070 Left & 14069 Right Composite

6. Side Panel Horizontal Spindles (10)* - 10605 White / 14068 Composite

7. Side Panel Vertical Spindles Long (6 ) - 10606 White / 14071 Composite

8. Side Panel Horizontal Bottom Rails (2) - 10603 White / 14072 Composite

9. Ground Anchoring Stakes (4) - 10608-1 White / 14073 Composite

10. 5/8” (1.6 cm) Self-Augering Stainless Steel Screws-(48) - 20016 White

20030 Composite

*) Arch Rafters & Side Panel Horizontal Spindles are the same parts.

Tools You Will Need

• Cordless Drill

• Level

• Stool or Short Ladder

• Shovel

• Cement (For Installation)

General Information

Read Instructions through carefully before beginning assembly.

• When assembling components, place on a non-abrasive surface

(i.e. shipping box) to avoid scratching.

• We recommend an area approx 10’x 8’ (3 m x 2.5 m) for unobstructed assembling.

• You should not need to use excessive force when assembling components.

Please read through before starting assembly.

IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

Check Box for These Contents

In the event of missing or defective parts please call our customer service dept. at

1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST).

ASSEMBLY INSTRUCTIONS

Athens Arbor / Arch

Sierra Composite Arbor / Arch

36 in

(91 cm)

20 in

(51 cm)

78.5 in (199 cm)

7.5 in (19 cm)

50.75 in (129 cm)

Not to Scale

V1.3/131120

39 in

(99 cm)

23 in

(58 cm)

www.wearevita.com

Summary of content (4 pages)

PAGE 1
A S S E M B LY I N S T R U C T I O N S Athens Arbor / Arch Sierra Composite Arbor / Arch www.wearevita.com 78.5 in (199 cm) 50.75 in (129 cm) 7.5 in (19 cm) 20 in (51 cm) 36 in (91 cm) 39 in (99 cm) 23 in (58 cm) Please read through before starting assembly. IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST). 1.
PAGE 2
PLEASE NOTE: All of the horizontal rails, spindles and arch rafters have locking tabs located at both ends. Once inserted and pushed into the routered holes, they will lock into place permanently. 1 STEP ONE Assemble the Arch System 1 Slide post caps into position as illustrated. Push firmly until the arches bottom out inside the post caps. 2 Join arches together as illustrated. 2 3 Fasten 4 screws in post cap at top of arch as illustrated (Fig 1), and repeat for other arch.
PAGE 3
Insert the horizontal spindles into the posts in the ‘sandwich’ pattern as illustrated. 4 Front Lay out the opposite post from point #2 as illustrated and complete the side panel by inserting it into the post. Back 5 Front Fasten the horizontal side panel rails at the intersection of each post with 2 screws. This will stiffen your side panel. 6 Repeat for other side panel.
PAGE 4
Arbor Installation A A Into Earth (temporary Installation) 1 Move the arbor to its final location (you will need a helper). When you are satisfied with the location, mark the locations of the posts, then move the arbor aside and lay it carefully on its side. Excavate 4 holes approx. 10” (25.5 cm) deep. Carefully move the arbor back into position and level it both vertically and horizontally. 2 1 10" (25.5 cm) Backfill the holes with the excavated soil to cover the anchors. 6" (15.