Instructions / Assembly

ManualsBrandsVita ManualsGarden Arbors4.98-ft W x 7.83-ft H White Garden Arbor

Check Box for These Contents

In the event of missing or defective parts please call our customer service dept. at

1 800 282 9346

(Mon. to Fri. 8:00 AM to 5:00 PM EST).

1. Keystone Top Lid (2) - 10710-1

2. Keystone Internal Connectors (2) - 10711-1

3. Arch Keystones (2) - 10684-1

4. Keystone Bottom Plate (2) - 10712-1

5. Arches (4) - 10687-1

6. Arch Rafters (8)

1 1/2” x 1 1/2” x 25.9" [3.8 x 3.8 x 65.8 cm] - 10778

7. Post Caps (4) - 10728-1

8. Side Panel Horizontal Rails (4)

1 1/2” x 1 1/2” x 27.7” [3.8 x 3.8 x 70.4 cm] - 10777

9. Posts (4) 4’x4‘x70.5“

[10.2 x 10.2 x 179.1 cm] - 10775

10. Side Panel Diamond Lattice (2) - 10776

11.

#8 x

1 1/2 in. (3.8 cm.)

Stainless Steel Screws

(for Keystone and Arch to Post

Connection) (24) - 20005

Tools You Will Need

• Hammer

• Tape Measure

• Level

• Stool or Short Ladder

• Shovel or Auger

• Cordless Drill

General Information

• Read Instructions through carefully before beginning assembly.

• When assembling components, place on a non-abrasive surface

(i.e. shipping box) to avoid scratching.

• We recommend an area approx 10’x 8’

(3 m x 2.4 m) for unobstructed

assembling.

• You should not need to use excessive force when assembling components.

Please read through before starting assembly.

ASSEMBLY

INSTRUCTIONS

The Nantucket Legacy Arbor

Arch

(Not to scale)

IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

www.wearevita.com

V2.5_111020

102.25 in

259.7 cm

95 in

241.3 cm

52 in / 132.1 cm

60 in / 152.4 cm

102.25 in

259.7 cm

20 in

50.8 cm

28 in

71.1 cm

71 in

180.3 cm

68 in

172.7 cm

*Nantucket Legacy with Trim Kit Shown Above.

If you purchased the arbor / arch along with our decorative trim kit (BP80001),

there will be a separate box with the following contents;

12. Post Trim Caps (4)

13. Base Molds (4)

Summary of content (5 pages)

PAGE 1
A S S E M B LY I N S T R U C T I O N S The Nantucket Legacy Arbor / Arch 102.25 in 259.7 cm 95 in 241.3 cm www.wearevita.com 102.25 in 259.7 cm 68 in 172.7 cm 71 in 180.3 cm *Nantucket Legacy with Trim Kit Shown Above. Please read through before starting assembly. 52 in / 132.1 cm 60 in / 152.4 cm IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. 20 in 50.8 cm 28 in 71.1 cm Check Box for These Contents In the event of missing or defective parts please call our customer service dept.
PAGE 2
STEP ONE Assemble the Arch System NOTE: There are locking tabs located at the ends of each rafter. Once inserted and pushed into the routed holes, they will lock into place and cannot be removed. 1 Insert arches into arch keystone ensuring they terminate flush to the internal connector. 2 Fasten the top of the arches to the keystone insert by installing 1 1/2 in. (3.8 cm.) screws into the two flanges on either side of the top of internal connector.
PAGE 3
STEP T WO Assemble the Side Panels 1 Insert the Lattice into the horizontal rails as illustrated. 2 Lay post on flat surface with holes facing up. 3 Insert assembled panel into post. Push until tabs lock into place. 4 4 Layout opposite post and insert the side panel assembly as shown. 2 3 1 Push until locking tabs on rails “snap” into place. 4 NOTE: if you intend to install a gate or wings from the arch, before you install the arch, insert a 1 x 4 (3 cm x 10 cm) wood board approximately 5 ft.
PAGE 4
STEP THREE 1 Install the Side Panels You have Three Options to Complete this Step. (All purchased separately) OPTION ONE - If Your Arch: • is going to be installed with fencing or a gate • is located in a high wind or hurricane area • is located in ground conditions that are not level Consider Using: A - 4x4 Professional Post Extension Kit (30 in./76.2 cm. long), (Kit of 4) • Purchase from Vita, www.wearevita.
PAGE 5
STEP FOUR Connect the Arch System to the Side Panels 3 1 1 Temporarily position post caps on bottoms of arches. 2 With a helper, insert the bottom of the arches into the posts until the arch rest on the stopper bolts. * If you purchased trim kit, slide the post trim caps down the posts before the arch. 3 Slide post caps down into position. 4 Install 2 - 1 1/2” (3.8 cm) screws into the two pre-drilled holes per posts.