Mighty Series WDR Dome Cameras 700 TVL Pixim-Powered WDR Dome Cameras VITEK • Pixim D8800C Seawolf Digital Imaging System CMOS • 700 TVL High Resolution • WDR - Wide Dynamic Range • 3DNR - Three Dimensional Noise Reduction • Secondary Video Output (Cable Included) • OSD (On Screen Display) for Camera Function Setup • Flush or Surface Mount • Infinity Ball Mount for Any Viewing Angle • UTP interface and Heater / Blower Options Available • UTC Control - Serial Control over Coax • ¾” Conduit Knockouts • Ind
TABLE OF CONTENTS BOX CONTENTS MOUNTING ACCESSORIES AVAILABLE MODELS/ACCESSORIES MIGHTY DOME LAYOUT INSTALLATION JUNCTION BOX INSTALLATION OPEN GIMBAL COVER CONNECTIONS LENS ADJUSTMENT INFINITE AXIS GIMBAL ADJUSTMENT WDR MIGHTY DOME FEATURES OSD MENU FEATURES/SETUP 1 1 2 3 4 5 6 7 8 9 10 10 1. In the menu 11 2. Entering Menu 11 3. MAIN 11 4. EXPOSURE 12 5. DAY/NIGHT 13 6. 3D NR 14 7. DC LENS or MANUAL LENS 14 8. PICTURE CONTROL 15 9. SPECIAL 15 10. MOTION 16 11. PRIVACY AREA 17 12.
BOX CONTENTS 1) Dome Camera 2) Accessories 3) VT-MD-2VOC (Secondary Video Output Cable) VITEK 4) Instruction Manual & Mounting Template INCLUDED ACCESSORIES Torx Wrench - (Vandal & IR Versions Only) Type #: T20 Length: 63mm / Diameter: 4mm Qty: 1 Phillips head Screws - (Vandal & IR Versions Only) For attaching the dome cover to the flush housing.
AVAILABLE MODELS / ACCESSORIES Indoor Mighty Dome Configurations: VTD-MP2810WDR: Indoor Wide Dynamic Range Color Dome Camera with 2.8-10mm Varifocal Lens & 700TVL VTD-MP922WDR: Indoor Wide Dynamic Range Color Dome Camera with 9-22mm Varifocal Lens & 700TVL VTD-MP1850WDR: Indoor Wide Dynamic Range Color Dome Camera with 18-50mm Varifocal Lens & 700TVL Vandal Resistant Mighty Dome Configurations: VTD-MVP2810WDR: Vandal Resistant Wide Dynamic Range Color Dome Camera with 2.
MIGHTY DOME LAYOUT 1) Lens 8) Dome Cover Ring 2) Power Input Connector(12VDC / 24VAC) 9) Flush Mount Base 10) Surface Mount Plate 3) Video Output Connector - BNC 11) Assembly Screws - Torx M4x9 (Vandalproof) 4) Camera Holder and 2nd Video output 12) Assembly Screws - Phillips ST4x12 (Indoor) / Phillips M4x10 (Vandalproof / IR) 5) Ball with the Camera Assembly 6) Safety Wire 13) Mounting Screws - Phillips ST4x30 7) Bubble 3
INSTALLATION 1) Dome Cover 1.1 Vandal Proof Domes - Use the provided Torx wrench to unscrew the vandal proof screws and remove the dome cover. 1.2 Indoor Domes - Turn the dome cover to the left to remove the dome cover. 2) Flush Mount Installation: Using four St4x30 screws, attach the flush mount base to a sturdy surface. Optional flush mount decorator plate. Model: VT-MD-FMP 3) Surface Mount Installation: Drill pilot holes at the mounting location using the provided mounting template.
JUNCTION BOX INSTALLATION Mighty Domes can easily be flush or surface mounted to an electrical junction box (4S J-Box) using the pre-drilled mounting holes on either the surface mount housing or the the flush mount base.
OPEN GIMBAL COVER To adjust the zoom and the focus, the gimbal needs to be removed temporarily from its base. 1) Remove the ball gimbal from its socket, and hold the base firmly with one hand. 2) Gently squeeze Point A and B and pull away from the base until the gimbal is removed from the base. 3) Replace the Gimbal cover by aligning the cover to the base and pressing down until it snaps back onto the base.
CONNECTIONS • Power connection: 12VDC or 24VAC dual input. • All Mighty Dome cameras come standard with a secondary video output. The secondary video cable (VT-MD-2VOC) is included in the box.
LENS ADJUSTMENT 1) Remove the Gimbal cover from the Gimbal base. 8 2) Loosen Zoom & Focus screws and make necessary adjustments as shown. Field of view: Telephoto(T) to Wide(W) Focus: Near(N) to infinity( ) 3) OSD Joystick Control 4) Reattach the gimbal cover to the gimbal base.
INFINITE AXIS GIMBAL ADJUSTMENT Rotation and “Friction Hold” Placement The Gimbal mechanism yields maximum rotation and placement as shown below.
WDR Mighty Dome Features CMOS image sensor: - Provides the best quality image without any blooming or vertical smear even under the spot light. Pixim’s DPS technology: - Offers unparalleled image quality across all lighting conditions especially in high contrast environments such as indoor and outdoor elements combined in the same field of view, or other extreme bright & dark lighting elements combined in the same image.
OSD Menu Features/Setup SETUP 1 In the Menu Use press , buttons to move the menu, , buttons to change the settings and button to select or enter. standsstands for MENU or ENTER button. button for MENU or ENTER. 2 Entering Menu Press button longer for than 2 seconds on the back of the camera. 3 MAIN Follow the chart below for submenu settings MENU Default Descriptions EXPOSURE Sets COLOR ROLL COMP., AE PREFERENCE, WDR CONTROL and SENSE-UP.
OSD Menu Features/Setup 4 EXPOSURE To enter EXPOSURE menu, press EXPOSURE EXPOSURE WDR HIGH COLOR ROLL CUSTOM... COMP. BLC... WDR LOW AE PREFRENCE WDR CONTROL SENSE-UP Default button at MAIN>EXPOSURE. Descriptions Descriptions In the NTSC system, the entire tone PRESETs. on the monitor may continuously Medium level of dynamic range controlcolor for each show reddish and greenish. Increases the COLOR dynamic ROLL range COMP. control. -Some highlight arearolling may washed out.
OSD Menu Features/Setup 5 DAY/NIGHT To enter EXPOSURE menu, press button at MAIN>DAY/NIGHT>AUTO IMPORTANT!!! IMPORTANT!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final step of the installation. Block the lens for a few seconds for NIGHT mode and release and let it return to DAY mode. If camera stays at NIGHT mode more than 10 seconds, increase N-->D THRES a little and repeat the fore-mentioned steps.
OSD Menu Features/Setup 6 3D NR To enter EXPOSURE menu, press 3D NR Default DEPTH 47 button at MAIN>3D NR Descriptions Determines the depth of Three Dimensional Noise Reduction. High value effectively reduces the noise but a comet effect may occur for a fast moving object and vice versa. 7 DC LENS or MANUAL LENS To enter EXPOSURE menu, press button at MAIN>LENS SELECT>DC... or MANUAL...
OSD Menu Features/Setup 8 PICTURE CONTROL To enter the EXPOSURE menu, press PICTURE CONTROL button at MAIN>PICTURE CONTROL. Factory Default Descriptions WHITE BALANCE ATW NORMAL Sets ATW Normal, ATW Desat, ATW Xtnd or MANUAL. ATW NORMAL – Compensates automatically in range of 2800K-7500K. ATW DESAT – Compensates automatically in range of 2000K-11000K. In the range of 2000-2800K and 7500-11000K, white balance is gradually compensated. ATW Xtnd – Compensates automatically in range of 2000K-11000K.
OSD Menu Features/Setup SPECIAL Default Descriptions MOTION OFF If it is set to ON and motion is detected, MOTION message will appear on the monitor. See page 16, ‘MOTION ’ for settings. PRIVACY MASK OFF If set to ON, it is available up to 6 privacy masks . See page 11, ‘PRIVACY Area’ for settings. SYNC INT 1 Sync is fixed to INT1. LAN GUAGE ENGLISH VIDEO STANDARD NTSC RS485 CONTROL English is available only. Able to switch NTSC or PAL.
OSD Menu Features/Setup 11 PRIVACY AREA Up to 6 privacy areas can be programmed in size, position and mask color. Use joystick to change size, position and mask color. Right after pressing button at ON, the 1st zone appears on top-left corner in orange. The orange colored zone can be relocated in its location with , , , buttons. , An example of the mask when resizing with , Press , , Image after pressing button again. (1st zone changes to blue) Blue colored zone can be resized with , , buttons.
OSD Menu Features/Setup 12 RS485 CONTROL RS485 CONTROL Default CAMERA ID 1 ID DISPLAY OFF PROTOCOL VITEK BAUD RATE 2400 Description Determines the camera’s identification (between 1 and 255) Displays camera title on top-left corner of the screen. VITEK is available only. Select 2400/4800/9600/19200 bps. 13 D-EFFECT D-EFFECT Default FREEZE OFF Image freezes and shows the still image at the moment when set to ON.
OSD Menu Features/Setup 14 EXIT MENU-2 Descriptions EXIT Exits menu with discarding any changes. SAVE AND EXIT Exits menu after saving the parameters. FACTORY SET Restores and saves all parameters of factory settings. Camera resets and restarts automatically.
HEADER DIMENSIONS Vandal 31 Indoor 20
HEATER / BLOWER SPECIFICATIONS HEADER Specifications Power Supply 24 VAC Power Consumption 10W (Heater) / .
INDOOR MIGHTY DOME SPECIFICATIONS HEADER Specifications Image Device NTSC PAL Pixim D8800C Seawolf Digital Imaging System CMOS Effective Pixels Scan Frequency Synchronization 758(H) X 540(V) 59.94HZ(V), 15.734K HZ(H) 50HZ(V), 15.625K HZ(H) Internal / Line Lock (Phase Adjust) Horizontal Resolution 700TVL Sensitivity 0.00008Lux at F1.
VANDAL MIGHTY DOME SPECIFICATIONS HEADER Specifications Image Device NTSC Pixim D8800C Seawolf Digital Imaging System CMOS 758(H) x 540(V) Effective Pixels Scan Frequency Synchronization PAL 59.94HZ(V), 15.734K HZ(H) 50HZ(V), 15.625KHZ(H) Internal / Line Lock (Phase Adjust) 700TVL Horizontal Resolution Sensitivity 0.00008Lux at F1.
VTM-LCDP Series 15” 17” and 19” Professional LCD Monitors • 15” 17“ and 19” Professional LCD Display Panels • Designed for continuous 24/7 operation • VGA, Looping BNC Composite, and S-Video Video Inputs.
CHRONO Series 8, and 16 Channel Digital Video Recorders • Highly efficient H.264 compression H.
LIMITED LIABILITY WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
