VT-H41 4 Channel Digital Video Recorder with H.264 Compression VITEK • 4 Video Inputs with 1 BNC & 1 VGA Outputs • H.
VT-H41 SAFETY PRECAUTIONS EXPLANATION OF SYMBOLS This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. This symbol is intended to alert the user to the presence of unprotected “dangerous voltage” within the product’s enclosure that may be strong enough to cause a risk of electric shock WARNING To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
VT-H41 Do not place a container holding water or other liquids above the unit when it is connected to power. Do not allow the unit to get wet. Do not use during thunder/thunder storms unless used with an uninterruptable power supply (UPS). Do not place in an unstable position. Do not expose to shock or vibration. Do not use this unit in areas where it is exposed to the possibility of explosion. CAUTION Do not pull on the power cable when removing the power plug from the outlet.
VT-H41 Main features H.264 Video compression QUADPLEX operation enabling simultaneous recording, playback, networking, and backup.
VT-H41 System components and Installation Requirements for installation and safety This chapter is for the requirements for safe installation and use. This kit should be installed on a flat table or in a rack. The location in which the DVR is installed in the room is very important for proper operation of the system. When the DVR is installed too closely together or the location is poorly ventilated, the DVR may not operate properly and maintenance of the DVR may be difficult.
VT-H41 Components The package contains the main unit and its components as specified below. When you purchase the package, please check to ensure the components specified below are included. DVR Remote Controller Battery1.
VT-H41 SPECIFICATIONS ITEM Video Input Channel, Input Level Output Audio Alarm VT-H81 (8CH) VT-H161 (16CH) 4CH, Composite 8CH, Composite 16CH, Composite Signal Format NTSC/PAL Video Loss Check Yes Main Monitor Output 1 CH BNC, 1CH VGA: Selectable Signal Format NTSC/PAL & VGA Input & Output 4 CH Line input & 1 CH Line output Audio Codec G.
VT-H41 Termination Yes Dynamic DNS Yes (Free DDNS) Network Interface 10/100 base-TX Ethernet (RJ-45) Client Software (1:1) Live, Search, Backup, PTZF Camera Control Web viewer (1:1) Live, Search, Backup, PTZF Camera Control Multi-sites Monitoring System (1:n) Live, Search, Backup, PTZF Camera Control DLS (Day Light Saving) Yes Internal Beep By Alarm, Motion, Video Loss, HDD error Multi-Language Yes S/W Upgrade USB Flash drive Water - mark Yes (Exclusive viewer) Power source Power D
VT-H41 INDEX 1. NAME & FUNCTION................................................................................................... 10 1-1. Front panel.............................................................................................................................................10 1-2. Remote controller .................................................................................................................................11 1-3. Rear panel and connection .............................
VT-H41 7-2. Installing the network viewer .............................................................................................................55 7-3. Live monitoring mode and functions. ..............................................................................................56 7-4. Bi directional audio..............................................................................................................................58 7-5. Remote search mode and functions ..........................
VT-H41 1. NAME & FUNCTION 1-1. Front panel SEQ: To start auto sequencing of the screen in full screen mode. (Toggle) PTZ: To control PTZ operation SETUP: To launch SETUP menu. CAPTURE: To start operations of backup in live or playback mode. SEARCH: To go to the search menu. REC: To start and stop manual recording. PLAY/PAUSE: To play or to pause the footage in playback mode. REW: To rewind the footage at 1x, 2x, 4x, and 8x speed during playback.
VT-H41 1-2. Remote controller ID: When a remote control ID number is set in DVR, press it before number. REC: To start and stop manual recording. Number: To select channel (1, 2, 3, & 4) or to enter DVR ID number. F/REW: During playback - To move the playback position 60 seconds backward. During pause - To move the playback position 1 frame backward. F/ADV: During playback - To move the playback position 60 seconds forward. During pause - To move the playback position moves 1 frame forward.
VT-H41 1-3. Rear panel and connection 1-3-1. Basic connections Do not power this system on before all the connections are completed. Make sure all the connections are made properly. Faulty connection may result in the system being damaged. The DC plug of the AC adaptor is easy to be unplugged.
VT-H41 Table 1.2 Rear Panel Connections VIDEO IN Four connectors for video input. Connect camera cable to Video-in (NTSC/PAL) VIDEO OUT Composite video output in NTSC or PAL format. Connect to Composite Monitor. VGA RS-232 SENSOR IN ALARM OUT LAN DC 12V Connector for VGA monitor For engineering use only Connector for sensor device. 4 sensors can be connected to the system. Sensor 1, 2, 3, 4 are dedicated to Video channel 1, 2, 3, 4, respectively.
VT-H41 Internet (ADSL) Connection Connect to the system, using a Router or ADSL modem and an Ethernet cable (10BASE-T/100BASE-TX CAT 5 LAN cable) 1-3-3. Sensor and alarm connections SENSOR INPUT: Connect two signal lines of sensor (infrared ray sensor, heat perception sensor, magnetic sensor) to the desired sensor number. NOTICE SENSOR inputs need dry contact only. Do not input any electric signal.
VT-H41 ---: Not operational N/O: Normally open type sensor. When magnetic sensor is closed, sensor sends a signal. N/C: Normally closed type sensor. When magnetic sensor is opened, sensor sends a signal. ALARM OUTPUT: Use Maximum current: 0.5A/125VAC, Maximum voltage: 1A/30VDC. When controlling lamp and AC operated equipment, control it using separate outside relay.
VT-H41 2-1-2. VGA: Select VGA to connect computer VGA monitor The general TV monitor terminal and the computer VGA monitor terminal can not be used 2-2. Live screen While the system is booting, “INITIALIZING” message is displayed. After the system booting is finished, the video inputs from the cameras are displayed. Various indicators showing the status of the DVR are shown as OSD symbols. These OSD and video display can be hidden.
VT-H41 Indicator Description C R S M T h e i T h e i Continuous recording in progress Manual recording in progress Sensor alarm recording in progress Motion alarm recording in progress T h e i Indicates that audio/audios is/are mute, single, or mixed. T h e i Indicates that alarm is detected T h e i Indicates that motion is detected T h e i Indicates that a network client is connected to the DVR. T h e i Indicates that sequencing mode is enabled. R:A,0..
VT-H41 button and select the date format using button. 3. Go to DATE FORMAT field using YYYY/MM/DD (Ex. YYYY-MM-DD (Ex. 2008-05-06) 2008/5/6) 4. Go MM/DD/YYYY TIME field using MM-DD-YYYY to DATE & DD-MM-YYYY button and press the SEL button. 5. Select the date and time that is to be changed using button, change a value using button, and press the SEL button. Then UPDATE DATE & TIME screen is displayed. 6. Select CONFIRM and press the SEL button.
VT-H41 deleted. Selecting “GO TO TEST MODE”: Selects only the video data between “SYSTEM TIME” and “HDD LAST TIME” and will not be deleted. Otherwise, do not select “GO TO TEST MODE”. 2-4. DLS (Day Light Saving) time setting EU Territory – When your time zone belongs to EU territory 1. Go to SYSTEM>DLS field using 2. Go to GMT AREA field using button and select EU using button. button and select GMT time of your country from +00:00 to +05:00.
VT-H41 2. Select BEGIN field using button and press the SEL button. Then DAYLIGHT SAVING BEGIN screen is displayed. 3. Select the date and time that is changed using button, change a value using button, and press the SEL button. 4. After exit from DAYLIGHT SAVING BEGIN field setting, select DAYLIGHT SAVING END field using button and press the SEL button. Then DLS BEGIN screen is displayed. 5.
VT-H41 3. OPERATION - RECORD The system has 6 recoding modes. CONTINUOUS recording – Recording continuously when the DVR is turned on. C icon is displayed on the screen. (Refer to page 25) MOTION DETECTION recording – Recording when the DVR detects motion form input video. M icon is displayed on the screen. (Refer to page 25) SENSOR recording – Recording when the external sensor of DVR is set off. S icon is displayed on the screen.
VT-H41 Repeat this step to set the other channel as necessary. Press ESC button to go to SAVE SETUP and save the . 3-2. MOTION DETECTION recording A motion detection setting is available for each channel. Set the basic record menu using the direction buttons before setting Motion detection. RESOLUTION CHANNEL: FRAME RATE QUALITY Upon Motion detection, the DVR records input video with these setting.
VT-H41 When FULL ZONE is selected, the DVR detects motion from the entire video screen. Set only MOTION SENSITIVITY. Select the grids for motion detection using button and SEL button. Then the selected grids are displayed in Pink color. Go to MOTION SENSITIVITY using button and select the sensitivity using button.
VT-H41 Go to POST RECORD using button and select the time as necessary using button. The available POST RECORD time: 5 to 60 seconds. Repeat this step to set the other channel as necessary. Press ESC button to go to SAVE SETUP and save the setting 3-3. SENSOR recording Sensor is connected to each channel and be used a recording trigger. Connect a sensor to a sensor terminal on the rear of the DVR.
VT-H41 Go to RECORDING BY field using button and select SENSOR using button. Go to DEVICE>CHANNEL>SENSOR RECORDING using button and select the number of sensors that are linked with the video channel using button. Go to PRE RECORD using Go to POST RECORD using button and select ON or OFF as necessary using button. button and select the time as necessary using button. Repeat this step to set the other channels as necessary. Press ESC button to go to SAVE SETUP and save the setting.
VT-H41 Go to ALARM/BEEP DURATION using button and select alarm/beep duration as necessary using Enter button. Press ESC button to go to SAVE SETUP and save the setting. 3-4. Manual recording To start manual recording, press REC button. Then, “R” is displayed on the screen and the DVR starts recording all channels. To stop manual recording, press REC button. Then, “R” disappears on the screen and the DVR stops recording all channels. 3-5.
VT-H41 MOTION ZONE MOTION SENSITIVITY SENSOR TYPE PRE RECORD POST EVENT RECORD Go to RECORDING BY field using Go to SCHEDULE using button and select SCHEDULE using button. button and press SEL button. Then SCHEDULE setting screen is displayed. (When the channel 1 is selected from CHANNEL field, “SCHEDULE – CH1” is displayed.) Move the cursor to one of following fields and set a different mode using SEL button. : Same recording mode setting applies to every day.
VT-H41 : MOTION DETECTION recording mode setting applies to the whole day. : SENSOR recording mode setting applies to a specified time of every day. EXAMPLE of copying the CH1 SCHEDULE recording setting to CH2 Set the CH1 SCHEDULE and return RECORD menu using ESC button. Go to CHANNEL field and select CH2 using buttons. And go to SCHEDULE field and press SEL button. Then SCHEDULE – CH2 screen is displayed. Move the cursor to COPY FROM using buttons and select CH1 using buttons.
VT-H41 press SEL button. Then the CH1 SCHEDULE recording setting is copied to CH2. 4. OPERATION - PLAYBACK The system has 7 methods of searching a recorded video. EVENT SEARCH – Searching through the calendar, channel, and recording mode. (Refer to page 33) TIMELINE SEARCH – Searching through the calendar and the timeline. (Refer to page 34) GO TO SPECIFIC TIME – Searching through selected date and time. (Refer to page 35) GO TO THE FIRST VIDEO – Searching the oldest recorded video.
VT-H41 Go to EVENT SEARCH and press SEL button. Then SEARCH screen is displayed. Select the date, a channel, and the type of recording mode using buttons and SEL button. A: Showing all the recorded data list of every type of recording mode M: Showing the recorded data list by motion detection. (BY MOTION) S: Showing the recorded data list by sensor detection. (BY SENSOR) R: Showing the recorded data list by manual recording. C: Showing the recorded data list by continuous record.
VT-H41 4-2. TIMELINE SEARCH Press SEARCH button. Then SEARCH menu is displayed. Go to TIMELINE SEARCH and press SEL button. Then SEARCH calendar screen is displayed. Select the date using buttons and SEL button. Then Timeline screen is displayed. Move the vertical Yellow line to the time between 0 to 24 HOUR using buttons and SEL button. Move the vertical Yellow line to the time between 0 to 60 MIN using buttons and SEL button. Then, playback starts.
VT-H41 4-3. GO TO SPECIFIC TIME Press SEARCH button. Then SEARCH menu is displayed. Go to GO TO SPECIFIC TIME and press SEL button. Then SEARCH screen is displayed. Select the date and time using buttons and press SEL button. Then, playback starts. When there is no recorded data, the closest data to the selected time is played back. 4-4. GO TO THE FIRST VIDEO Press SEARCH button. Then SEARCH menu is displayed. Go to GO TO THE FIRST VIDEO and press SEL button.
VT-H41 4-6. SYSTEM LOG Press SEARCH button. Then SEARCH menu is displayed. Go to SYSTEM LOG and press SEL button. Then SYSTEM LOG calendar screen is displayed. Select the date using buttons and press SEL button. To change pages of the log data list, use buttons. Then, log list screen of the date is displayed. 4-7. ARCHIVE The archived still-images or video in Live screen or Playback screen can be searched and played back. Press SEARCH button. Then SEARCH menu is displayed.
VT-H41 Select the date using buttons and press SEL button. Then ARCHIVE LIST screen is displayed. Select one of the archived data listed using buttons and press SEL button. To change pages of the archived data list, use buttons. Then, the archived still-image or the first frame of video data is displayed. 5. OPERATION - BACKUP TO USB FLASH DRIVE JPEG and video can be backed up to USB flash drive.
VT-H41 Archiving and backup JPEG in Live mode – JPEG image can be archived on HDD and be backed up to USB flash drive in live mode. (Refer to page 39) Archiving and backup VIDEO in Playback mode – JPEG, AVI, or EXCLUSIVE VIDEO can be archived on HDD and be backed up to USB flash drive in playback mode. (Refer to page 40) Backup JPEG, AVI, or EXCLUSIVE VIDEO from ARCHIVE search – JPEG, AVI, or EXCLUSIVE VIDEO can be backed up from ARCHIVE search menu.
VT-H41 Then SAVING screen with backup status bar is displayed after “CHECKING USB” message. After the backup is done, “BACKUP IS COMPLETED” message is displayed. When the DVR can not recognize USB thumb drive or no USB thumb drive is connected to the USB terminal, “PLEASE CHECK BACKUP DEVICE” message is displayed. 5-2. Archiving and backup VIDEO in Playback mode Connect a USB flash drive to the USB terminal. Press SEARCH button and go to the video to be backed up.
VT-H41 Press CAPTURE button at the scene of video to be backed up. Then SELECT BACKUP FILE TYPE screen is displayed. Select a file type from JPEG, AVI, or EXCLUSIVE VIDEO using buttons and press SEL button. Then DURATION screen is displayed. When JPEG IMAGE is selected, please use the same backup procedure as Set the duration to be archived and backed up from the scene of video using and press SEL button.
VT-H41 After the backup is done, “BACKUP IS COMPLETED” message is displayed. 5-3. Backup JPEG, AVI, or EXCLUSIVE VIDEO from ARCHIVE search Press SEARCH button. Then SEARCH screen is displayed. Go to ARCHIVE field using buttons and press SEL button. displayed. Select the date in Red using displayed. 38 ARCHIVE search calendar is buttons and SEL button.
VT-H41 Select VIDEO clip from the list using buttons and SEL button. Then a paused image or the first scene of the video is displayed. Press CAPTURE button. Select AVI or EXCLUSIVE VIDEO using Select USB FLASH DRIVE using buttons and press SEL button. backup status bar is displayed. buttons and press SEL button.
VT-H41 After the backup is done, “BACKUP IS COMPLETED” message is displayed. 5-4. Playback of AVI or EXCLUSIVE VIDEO Playback of AVI format: AVI format video can be played back by Windows Media Player™ or other media player that is compatible with AVI format video. When PC doesn’t have proper H.264 CODEC, the media players can not playback the AVI format video.
VT-H41 6. SETUP Press the SETUP button, then the password window is displayed. The default password is 1111, which can be entered by pressing the up button 4 times and then pressing the SEL button. After input password, the SETUP screen is displayed. 6-1. LIVE Item OSD SEQUENCE Description Enable/disable OSD (on-screen-display).
VT-H41 mode. SEQ-DWELL TIME Dwell time for each cannel display in sequential display mode. OSD CONTRAST Set the visibility level of the On Screen Display (OSD) CHANNEL Select the channel for applying the following settings. DISPLAY Enable/disable display of the video channel in live display mode SEQUENCE LIST BRIGHTNESS CONTRAST HUE SATURATION Enable/disable the specified channel to be included in sequential list.
VT-H41 ON: The channel is included in sequencing channels. OFF: The channel is NOT included in sequence list. BRIGHTNESS – Set the brightness of the channel using buttons. Setting values of the display bar: 0% ~ 100% (The most brightness) CONTRAST – Set the contrast of the channel using buttons. Setting values of the display bar: 0% ~ 100% (The most contrast) HUE – Set the hue of the channel using buttons.
VT-H41 RESOLUTION – Select the resolution for the recording using buttons. 352x240: The input video is recorded as 352x240 resolution. 704x240: The input video is recorded as 704x240 resolution. 704x480: The input video is recorded as 704x480 resolution. The resolution setting is applied to every channel. Setting of CHANNEL - Select CHANNEL to set the recording setting as below using buttons FRAME RATE – Set the frame rate value using buttons.
VT-H41 6-3. DEVICE Item CHANNEL Description Select the channel for applying the following settings. MOTION ZONE Select Full Zone or Partial Zone for motion sensing. MOTION SENSITIVITY Set the motion sensitivity for the specified channel. SENSOR RECORDING Select the channel to link with sensor. SENSOR TYPE Select the sensor for applying the following settings.
VT-H41 ALARM - Select an event to link with alarm using buttons. OFF: An event signal is NOT linked with the external alarm. SENSOR: A sensor event signal is linked with the external alarm. MOTION: An event signal of motion is linked with the external alarm. VIDEO LOSS: An event signal of video loss is linked with the external alarm. HDD FAIL: An event signal of HDD failure is linked with the external alarm. ALL: Every event signal is linked with the external alarm.
VT-H41 FOCUS INITIALIZE RIGHT button for FOCUS near or far of the selected camera. Initialize the PTZ settings of the selected camera. REMOTE CONTROLLER ID (Example: Number 3) Select REMOTE CONTROLLER ID using buttons and select the ID number from 3 using buttons. And exit from the setup menu. Press the ID button on the remote controller and press the number 3 button. Then icon is displayed on the screen. BUTTON TONE - Enable / Disable the sound tone of front buttons using buttons. 6-4.
VT-H41 Input a port number using buttons and press SEL button. When you connect one or more DVRs to a network through an IP sharing device, each device must have a unique TCP port number for access to each unit from outside the LAN.
VT-H41 Input the registered PASSWORD that is necessary for ADSL connection using buttons and press SEL button. Press ESC button. Then the APPLY NETWORK ADDRESS screen is displayed. Select CONFIRM using buttons and press SEL button. Then the DVR reboots automatically. Use this ADSL (PPPoE) function when the network type connected to the DVR is PPPoE method.
VT-H41 1. Regarding the use of fixed IP, please ask your network administrator if you do not have this information. 2. When DVR is installed in IP sharer that is connected with ADSL, a user can assign fixed IP to DVR from IP sharer itself using “DMZ” function out of such Setting of DDNS – Select ON/OFF using buttons. ON: The network access by the pre-registered domain name address that is preregistered on www.vitekddns1.com is allowed. DDNS SERVER NAME appears.
VT-H41 6-5. STORAGE Item Description OVERWRITE Enable/Disable Overwrite existing old video data when hard disk drive is full HDD FORMAT DISK INFORMATION RECORD LIMIT Format hard disk drive Shows the HDD information Set the limit days for recording to the hard disk drive from 1 to 60 days OVERWRITE – Select ON/OFF using buttons. ON: When the HDD is fully recorded, former video data is deleted to record the new video data. OFF: When the HDD is fully recorded, the recording stops.
VT-H41 6-6. SYSTEM DESCRIPTION DATE FORMAT SET DATE & TIME Press SEL to see system information. Select the preferred date and time display. Set the present date and time. If DLS function is ON, user can not enter into this menu and change data and time. Set DLS (Daylight Saving). DLS ADMIN PASSWORD Set the password for the administrator. The default password is 1111. NETWORK PASSWORD Set the password of network client. The default password is 1111. Select a language.
VT-H41 NETWORK PASSWORD – Select NETWORK PASSWORD using buttons and press SEL button. Then the NETWORK PASSWORD screen is displayed. Changing of PASSWORD (ADMIN/NETWORK) Select ADMIN PASSWORD / NETWORK PASSWORD using buttons and press SEL button. Then the Current password input screen is displayed. Enter the current password using (1) (2) (3) (4) buttons and press SEL button. Then the New password input screen is displayed.
VT-H41 menu setting value starts automatically.. After uploading is completed, then the DVR reboots automatically. USB UPGRADE Download the firmware of the DVR from the VITEK web-site www.vitekcctv.com . Create a new folder (This folder name should be “upgrade”) in the USB thumb drive and paste the firmware “app-xxx.bin” into the folder. Connect USB thumb drive to the USB port. Select USB UPGRADE using buttons and press SEL button.
VT-H41 7. Network access using the Exclusive network viewer The DVR provides a live remote monitoring feature. Remote monitoring requires installation of the network viewer on your PC. NOTICE In a high bandwidth network, a maximum of four users can access one DVR simultaneously. In a low bandwidth network it is recommended that only one user access the DVR at a time. 7-1. PC requirements CPU: Intel Pentium 1.2Ghz or higher Memory: 256MB (512MB or higher is recommended.
VT-H41 6. After the installation is completed, “UMS Client” icon is displayed on the desktop. 7-3. Live monitoring mode and functions. Button Function Description DATE & TIME Displays the current date and time. CONNECT/DISCONNECT Connect/disconnect connection..
VT-H41 Switches SEARCH the live mode to search mode. DISPLAY MODE Select a channel and screen display mode. PAN/TILT/ZOOM/ Control the PAN/TILT/ZOOM/FOCUS FOCUS features on the remote camera. CAPTURE Capture a still image from live screen. PLAY/PAUSE Play/pause live video. ALARM The ON/OFF button of the alarm output of the DVR. When an alarm of the DVR is output, this button becomes Red. Display SETUP the setup screen of the frames and network viewer.
VT-H41 Full screen display - Click the maximize button to display only video and hide the operation panel. Image capture of live screen Still-image of live screen can be captured and saved as BMP or JPEG file. 1. Click the channel to be captured. Then the channel screen is surrounded with a red line. 2. Click the CAPTURE button. Then the IMAGE CAPTURE dialog is displayed. 3. Set the conditions and click OK button. Then still-image is saved. 7-4.
VT-H41 7-5. Remote search mode and functions Button Function Description DATE & TIME Displays the recording time of the data selected on the time bar at the bottom of the main user interface. DISCONNECT Disconnect network connection. LIVE Switches the search mode to live mode. CAPTURE Capture a still image from live screen. MARK IN Set the start time for video backup. MARK OUT Set the ending time for video backup. BACKUP Backup the selected recorded video as AVI format.
VT-H41 SEARCH The calendar shows dates with recorded CALENDAR video in light blue and the selected date in dark blue. The timeline shows recorded data in dark TIMELINE BAR blue on the bar. The playback buttons. PLAYBACK BUTTON Select a channel and screen display mode. DISPLAY MODE Searching and playing video from the remote DVR/Client Video recorded in the remote DVR or Video recorded on the PC can be searched and played back. 1. Connect the network to the remote DVR and press SEARCH button.
VT-H41 Backup of video on the remote DVR Video recorded on the remote DVR can be backed up on the PC HDD as AVI format. 1. Connect the network to the remote DVR and play the video recorded in the remote DVR. 2. Drag the slide on the time scale and drop to the start time for video backup and press the MARK IN button. 3. Drag the slide on the time scale and drop to the end time for video backup and press the MARK OUT button. Then the marked time is displayed in dark green. 4.
VT-H41 7-6. PC System configuration Click the SETUP button. Then the Setup dialog is displayed. Setting General Set security options, save path, and Automatic reconnection. Security Option: Set a password for security options. When you access any of the selected functions, you will need to enter the password. Save Path: Specify the location to record for backup and still image capture.
VT-H41 Display network statistics: If a user selects this function, the client S/W will display network status, Bit rate and Frame rate. Time Format: Change the time format mode on the Client software display. Setting Site The remote DVRs can be added, modified, and removed. Setting Event Set the record path and the size of local disk space for the log files. LOG – Select to save event log into ‘log file’. ICON – Select to display the event on live video.
VT-H41 Setting Record Set the recording conditions and select channels to record. Select the local disk to use and the amount of disk space you want to allow the program to use for recording.
VT-H41 Setting Video Set the video screen. Setting Language Select the language of the network client viewer.
VT-H41 8. Network – By a web-browser viewer The DVR provides a live remote monitoring feature by web-browser viewer. 1. Check the IP address of the DVR from SETUP>SYSTEM>DESCRIPTION>IP ADDRESS. 2. Input the IP address or Domain name address that you pre-registered on www.vitekddns1.com on the address field and press “Go”. 3. Click this bar. Then the dialog box is displayed. 4. Click “Install” to download ActiveX control. 5. Web Browser Viewer is displayed as bellow. 6.
VT-H41 www.vitekddns1.com), Port number and Password and click “Connect” Server address: Input IP address of the DVR from SETUP>SYSTEM>DESCRIPTION>IP ADDRESS or Domain name address that you pre-registered on www.vitekddns1.com Port: Input Port number (The number sets on SETUP>NETWORK>PORT) Password: Input Password (The number sets on SETUP>SYSTEM>NETWORK PASSWORD 7. Then the cameras connected to the DVR are displayed on the screen.
VT-H41 APPENDIX: How to connect to a network A. How to set the IP address of the DVR and open the TCP port of the router? The port forwarding is dependant on the brand and model of the router. The port forwarding is required to allow access to the DVR beyond a router. 1. Connect network cable between DVR and Router or ADSL modem. 2. Default network setting on DVR are 3.
VT-H41 5. Open your web browser. Enter the router IP address in the address bar (The router IP address are different with the brand and model.), click GO. 6. Enter the user name and password (admin is default) and press the OK button. 7. Select the Port Range Forwarding tab. 8. Enter each field. i. Application: Enter a description of the DVR (Example: store1) ii. Start: Enter the first number of the port you need to port forward (Example: 5445) iii.
VT-H41 B. How to access DVR from Remote PC? LAN Connection – Using a switching hub Connect to the system, using a hub (Switching hub) and an Ethernet cable (10BASET/100BASE-TX CAT 5 LAN cable) 1. IP Router or HUB Run the pre-install the network client software on the supplied CD. (Refer to Chapter 6. Network access using the Exclusive network viewer) 2. Check the IP address from SETUP>SYSTEM>DESCRIPTION of DVR. 3. Run network client software and click the CONNECT button. 4.
VT-H41 Connect to the system, using an Router or ADSL modem and an Ethernet cable (10BASET/100BASE-TX CAT 5 LAN cable) 1. Go to SETUP>NETWORK. Set NETWORK TYPE as DHCP and DDNS SERVER as ON. And make sure that DDNS SERVER NAME is vitekddns1.com 2. Go to Setup menu of Router and open TCP port 5445 using Port Forwarding. (Refer to A. How to set IP address of the DVR and open TCP port of the router?) 3. Confirm the Mac address and Serial No. from the label of the rear panel of the DVR. 4.
VT-H41 Site Name: Input the name of the DVR. IP Address: Input the Domain Name that is registered on http://www.vitekddns1.com (EX. XXXXX.vitekddns1.com) 9. Port Number: Input the port number. Protocol: Select TCP. Password: Input the network password. Click CONNECT button. Then the Connect window is displayed. 10. Select the site that you want to access and click OK.
VT-H41 73
VT-H41 74
28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.
