VT-PTZ Series DISCLAIMER • While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. • Vitek reserves the right to change the specifications of the hardware and software described herein at any time without prior notice.
VT-PTZ Series WARNING AND CAUTION WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT.
VT-PTZ Series FCC COMPLIANCE STATEMENT FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT.
VT-PTZ Series IMPORTANT SAFEGUARDS 1. 2. 3. 4. 5. 6. Read these instructions. Heed all warnings. Follow all instructions. Do not use this equipment near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other equipment (including amplifiers) that produce heat. 8. Do not defeat the safety purpose of the polarized or grounding-type plug.
VT-PTZ Series TABLE OF CONTENTS DISCLAIMER_________________________________________________________1 WARNING AND CAUTION___________________________________________________2 FCC COMPLIANCE STATEMENT_____________________________________________3 CE COMPLIANCE STATEMENT______________________________________________3 IMPORTANT SAFEGUARDS_________________________________________________4 CONTENT VERIFICATION __________________________________________________7 MENU TREE __________________________________________
VT-PTZ Series TABLE OF CONTENTS 3.4 Zone Title_______________________________________________________41 3.5 Camera Title_____________________________________________________42 3.6 OSD Display_____________________________________________________42 4 CAMERA SETUP____________________________________________________43 4.1 Focus Control____________________________________________________43 4.2 WB (white balance) _______________________________________________44 4.
VT-PTZ Series CONTENT VERIFICATION Before installing the controller, please make sure that the following items are included in the box: 1. One Xpress Dome Camera 2. One Instruction Manual 3. Three Mounting Screws. 4. Three Plastic Anchors. 5. Two Eight-Pin Cable Assemblies. If any of these materials are missing, please contact the vendor or Vitek customer help desk immediately.
VT-PTZ Series MENU TREE 1.1 HOME FUNCTION (MENU ! Functions ! Home) 1. FUNCTIONS 1.2 PRESET (MENU ! Functions ! Preset Shortcut : PRST) 1.3 PATTERN (MENU ! Function ! Pattern or Shortcut: PTRN) 1.4 SCAN (MENU ! Functions ! Scan or Shortcut: SCAN) 1.5 TOUR (MENU ! Functions ! Tour, Shortcut: TOUR) 1.6 RUN FUNCTION (MENU ! Functions ! Run Function) 2.1 ALARM (MENU ! Actions => Alarm) 2. ACTIONS 2.2 ALARM LIST (MENU ! Actions ! Alarm List) 2.3 CLEAR ALARM LIST (MENU ! Actions ! Clear Alarm List) 2.
VT-PTZ Series INTRODUCTION Features The Speed Dome Camera features a high resolution EX-View HAD CCD imager for enhanced lowlight sensitivity. User friendly, on-screen pull-down menus and short-cuts make it easy to setup and program functions. System information aides trouble shooting by displaying the hardware and software version of the camera’s firmware version, baud rate, and protocol. ! Built-in Optical Power Zoom Camera. ! 248 Presets programmed with view direction, zoom, and BLC.
VT-PTZ Series INSTALLATION AND CONFIGURATION Typical system configuration Additional Speed Dome joystick controllers and a variety of external switching devices such as multiplexers (MUXes) and Digital Video Recorders (DVRs) may be incorporated to accommodate the needs from a small to a large surveillance/security system. Figure 1 illustrates sample installation.
VT-PTZ Series INSTALLATION AND CONFIGURATION Basic configuration of speed dome camera system Figure 2 - Basic Installation Diagram １１
VT-PTZ Series INSTALLATION AND CONFIGURATION Connecting the Speed Dome directly into the DVR • Locate the RS485 + & - conductor wire from the Speed Dome Camera. · Connect the + & - into the Tx+ & Tx- ports of the DVR. Tx+ & Tx- ports can be found in the rear part of the DVR.
VT-PTZ Series INSTALLATION AND CONFIGURATION Connecting both Speed Dome and DVR via J-BOX Figure 5 - Connecting Camera & DVR into Controller １３
VT-PTZ Series INSTALLATION AND CONFIGURATION The dome camera must be installed by qualified service personnel. Before installing the dome camera system, this instruction manual must be read thoroughly and understood fully. Dome cameras must be set up properly before starting the installation. This involves properly setting configuration switches. Figure 6 shows the location of these switches.
VT-PTZ Series INSTALLATION AND CONFIGURATION Setting the Web Baudrate Set baudrate of communication between control board and IP board.
VT-PTZ Series INSTALLATION AND CONFIGURATION Figure 10 - Termination Diagram １６
VT-PTZ Series INSTALLATION AND CONFIGURATION Dome Camera Address (ID) Each dome camera must have a unique address (ID). Identical IDs on the same line may damage the control circuit caused by an electrical short. When installing multiple dome cameras or a DVR, it is recommended that the dome camera ID’s be identical to the camera port of the DVR. Cam Port 1 = Dome ID1, Cam Port 2 = Dome ID 2 … Cam Port 16 = Dome ID 16.
VT-PTZ Series INSTALLATION AND CONFIGURATION Setting Protocols A Speed Dome camera is capable of negotiating with multiple protocols if the communication speed is matched (same baud rate i.e., 9600 bps). See Figure 13 for the appropriate protocol switch settings. Note: Consult service personnel if a dome camera is installed with a device other than a recommended Speed Dome Controller.
VT-PTZ Series INSTALLATION AND CONFIGURATION Connections How to Connect RS485 The dome camera has a built-in RS-485 receiver so that it can be controlled remotely by an external control device such as a joystick controller or a DVR. RS-485: Connect the TXA (Tx+) and TXB (Tx-) of the RS485/422 control devices (KBD, DVR…) to RXA(RX+), RXB(RX-) of the dome camera. RS-485 does not allow for a star connection layout. A splitter is required if a star connection layout is desired. RS-485 guarantees 1.
VT-PTZ Series INSTALLATION AND CONFIGURATION Mounting the Dome Camera Once all DIP switches are set properly and all external connections are made, the dome camera can be mounted. The Speed Dome camera is designed to mount on a structural body supporting loads up to 5 Kg. See Figure 14 Figure 14 - Example of a ceiling mounted installation Installation Hints Grab the dome head with hand as the picture above. 1. Align one of hook and guide rail than makes opposite hook fit. 2.
VT-PTZ Series INSTALLATION AND CONFIGURATION Power on and Boot-up Sequence When the power is applied to the dome camera, it will start the boot-up sequence. When boot-up is done, the following information is displayed on the monitor screen. XPRESS DOME On Screen Display in normal control mode 00/00/0000 00:00:00 AM 001PRESET >W ACTION1 Compass Direction EMPTY DATA ! Dome Camera Title ALARM:1 area title 360.0,090.0 3.
VT-PTZ Series PROGRAM & OPERATION Dome Camera Selection Prior to start programming or operating a dome camera, please make sure that both the camera and the joystick controller are communicating. In order for changes to take effect for a camera, particular camera’s ID must be selected on the controller. Example: Pressing 1 , 6 and CAM key sequentially will select dome camera 16. The selected dome camera ID will be displayed on the monitor.
VT-PTZ Series PROGRAM & OPERATION 1. FUNCTIONS (MENU =>Functions) By pressing the MENU button on the keyboard controller, the following On-screen MAIN MENU will be shown on the monitor screen. Select the Functions ICON and then twist the Joystick to CCW/CW to access Functions menu.
VT-PTZ Series PROGRAM & OPERATION 1.1 HOME FUNCTION (MENU =>Functions => Home) After Home item has been selected, follow the directions below to set Home function. ! Function : Tour/ Preset/ Pattern/ Scan ! Number : - - ! Time : 10~240 Seconds ! Operation : Enable/ Disable The Home function applies to the predefined functions such as Preset, Tour, Pattern, or Scan function after the keyboard controller has been idle for a programmed time. Follow the steps below to program the Home function: 1. 2. 3. 4.
VT-PTZ Series PROGRAM & OPERATION 1.2 PRESET (MENU => Functions => Preset Shortcut : PRST) Preset stores pan, tilt, zoom, focus and iris settings. Once programmed, pressing combination of 0 ~9 numbers and the Preset button on the controller should automatically call up the preset position. Presets may be assigned to alarm actions or as the “home” position for the dome camera. There are 31 pages of preset programming menu. Each page can hold up to 8 presets.
VT-PTZ Series PROGRAM & OPERATION 7. Select the desired character digit on the title line using Joystick Left/Right. 8. Move the cursor to the desired character on the character table using Joystick Up/ Down/ Left /Right, then twist the Joystick to CCW/CW (or turn right/left) at the desired character to complete selection, then the cursor position on the title moves to the next position automatically. 9. Twist the Joystick to CCW/CW (or turn right/left) at the “ALL DELETE” field to delete all characters.
VT-PTZ Series To enter the motion setup, twist the Joystick to CCW/CW (or turn right/left) on the motion setup. Sensitivity : 1-16(most sensitive) Hold Time : 03-99SEC: The hold time starts to count after the motion detects.
VT-PTZ Series PROGRAM & OPERATION To enter Advanced Motion Setup, twist the Joystick to CCW/CW (or turn right/left) on the motion setup. ! Mode: select tracking mode (PTZ must be set to Vitek protocol to use Tracking Mode) ACTION1 : Once a motion is detected, the camera starts and continues tracking. Until 5seconds after no motion is detected, the camera runs Lost Action. ACTION2 : Once a motion is detected , the camera starts and follows the object for 5 seconds.
VT-PTZ Series PROGRAM & OPERATION 1.3 SCAN (MENU => Functions => Scan or Shortcut: SCAN) The Scan function supports up to 16 programmed sections of angles at 8 program able speeds. ! SPEED (MODE) : 1/ 2 / 3/ 4/ 5/ 6/ 7/ 8/ SLW / MID 1: SLOWER ↔ 8 FASTER ! SLW : smooth Diagonal Scan in slowest speed ! MID : smooth Diagonal Scan in medium speed Diagonal Scan shows moving path from start point to end point including tilt and zoom** simultaneously.
VT-PTZ Series PROGRAM & OPERATION 6. Move the Joystick downward to select “END ANGLE.” Hold down the SHFT/PGM key while moving the Joystick to select the end position. The end position angle should be larger than start position. Release the SHFT/PGM key to complete the selection of the end position. (Or twist zoom handle or hit zoom button to start PTZ control and hit the Focus button to stop.) 7. Move the Joystick downward to select “Tilt & Zoom.
VT-PTZ Series PROGRAM & OPERATION !Title : 16 digits of title for tour label ! - - - : blank preset position ! SP : F-Normal/ M- Medium D.Scan/ S- Slowest D.Scan ! DW : 03-99 Sec ! Prst : PRESET 1~248 ! Ptrn : PATTERN 1~8 ! Scan : SCAN 1~16 ! Tour : TOUR 2~8 Follow the steps below to program the Tours: 1. Press MENU => Functions => Tour ( Short Cut: TOUR) to display the tour menu on the monitor. No. + SHFT+TOUR will open directly Tour No. 2.
VT-PTZ Series PROGRAM & OPERATION 1.5 PATTERN (MENU => Function => Pattern or Shortcut: PTRN) The Pattern function memorizes and stores movement of the selected dome camera for up to 480 seconds. Pattern can be stored in 480 seconds of total recording space. Stored pattern is played back by pressing No.+ PTRN buttons subsequently. Follow the steps below to program the Pattern: 1. Press MENU key to display the main menu on the monitor. 2. Simply press the PTRN key. (or MENU => Function=>Pattern) 3.
VT-PTZ Series PROGRAM & OPERATION 2. ACTIONS SETUP (MENU => Actions Setup) 2.1 ALARM ACTION SETUP (MENU => Actions Setup => Alarm) Highlight Alarm in the action setup and move the joystick to the right to access Alarm Setup setup. ! NO : Alarm input number ! FUNC : Stored function number to be called by alarm. ! Priority 1~8 calls Preset(xxx) ! Priority 0 supports dedicated functions like a Pattern(Pxx), Tour(Txx), Scan(Sxx). ! PRI : Lower No.
VT-PTZ Series PROGRAM & OPERATION There are 9 levels of priority. 0 : Highest priority supports repeated/dedicated functions like a Pattern(Pxx), Tour(Txx), Scan(Sxx). 1~8: Same level of alarm calls presets one after the other. Ex) Alarm 01 calls Pattern 01, after alarm 01 is released alarm 02, 03 will call preset 48 and preset 01 1. Press Menu to display the main menu on the monitor. Select the Alarm option by moving the Joystick up/down and then move to the right to enter the detail menu. 2.
VT-PTZ Series PROGRAM & OPERATION 2.3 CLEAR ALARM LIST (MENU => Actions Setup => Clear Alarm List) Select “YES” to clear the alarm list. 2.4 SCHEDULE ACTION SETUP (MENU => Actions Setup => Schedule Action Setup) The schedule action setup allows you to program to act the function as below at a specific date and time.
VT-PTZ Series PROGRAM & OPERATION ! Add Action To List: Add the current Schedule to the list ! Delete Action : Delete the current Schedule from the list Follow the steps below to program the schedule action: Create a new action: 1. Select the desired action number by moving the Joystick left or right or twisting the ZOOM handle at the action number field. 2. Select the desired function by moving the Joystick left or right or twisting the ZOOM handle at the function type field. 3.
VT-PTZ Series PROGRAM & OPERATION the camera always operates with the B/W mode. So don’t forget to program the second action for the day any night and an alarm out options NOTE: The function of the day and night (D/N:COLOR, D/N:B/W,D/N:AUTO) changes the camera menu setting and doesn’t affect the preset. So recommend you to set other preset for a night. ACTION DAY HOLIDAY: ! NO : The action will not occur on a day of the week for which it is set if that date is in the list of holidays.
VT-PTZ Series PROGRAM & OPERATION 2.5 LIST ACTION (MENU => Actions Setup => List Action) List action type: ALL, Preset, Scan, Pattern, Tour, Auto Pan, Day/Night, Alarm Out, Alarm In 1. Select the list action by moving the Joystick up or down. 2. Twists the ZOOM handle to select function type at the list action field 3. Push the Joystick right to sort the list according to the selected action type. 4. Push the Joystick right or left at the “Previous Next” to see the next numbers.
VT-PTZ Series PROGRAM & OPERATION 3. SCREEN (MENU => Screen) By pressing the MENU button on the keyboard controller, the following On-screen MAIN MENU will be shown on the monitor screen. Highlight Screen and then twist the Joystick to CCW/CW to enter Screen menu. 3.1 LANGUAGE SETUP (MENU => Screen => Language) Moving the joystick handle to the right to select Language options. Preferred language will be scrolled by moving the joystick to the right on Language ENGLISH.
VT-PTZ Series PROGRAM & OPERATION 3.2 PRIVACY ZONE SETUP (MENU => Screen => Privacy Zone) Highlight Privacy Zone and then move the joystick to the right to enter the menu. This function disables the viewing of restricted areas for privacy reasons. It offers masking up to 8 unwanted views in a camera. 1. Select the Privacy Zone option by moving Joystick Up or Down and move the joystick to right to enter the detail menu. 2. Select the privacy zone number by moving the Joystick up or down. 3.
VT-PTZ Series PROGRAM & OPERATION 3.4 ZONE TITLE (MENU => Screen =>Zone Title) Enter a specific name in sectioned angle between Start and End. 1. Press MENU => Screen => Zone Title to display zone title menu on the monitor. 2. Select the zone number by moving the Joystick up or down. Select Start, End or number column to be set by moving the handle to the right or left. The selected column will be highlighted. 3. Twist the joystick handle on the No. column to enter zone title.
VT-PTZ Series . PROGRAM & OPERATION 3.5 CAMERA TITLE (MENU => Screen => Camera Title) This function allows the users to set the title of camera as well as the usage of on screen display of the title. Twist the joystick handle on the Camera Tilie. Refer to the preset title 3.6 OSD DISPLAY (MENU => Screen => OSD Display) The following settings are available for each label except alarm. ! OFF : Label is not displayed when activated. ! ON : The label is continually displayed when activated.
VT-PTZ Series PROGRAM & OPERATION 4. CAMERA SETUP (MENU => Camera) NOTE: The menu features will vary depending on the camera module. ! Back Light : Objects in front of bright backgrounds will be clearer with BLC ON. NOTE: The Back Light operates in AUTO mode only. ! Sharpness : The higher the value, the more edges in the picture will be enhanced, TYPE A:(0~15), TYPE B:(0~63,AUTO) ! Digital Zoom OFF : Zoom range is limited to the optical. 2x : Zoom is extendable up to 2x of digital range.
VT-PTZ Series PROGRAM & OPERATION ! AF Sensitivity : NORMAL / LOW NORMAL: Use this option when shooting fast motion. LOW : Offers better focus stability. In low luminance conditions, Auto Focus stops operation even when brightness changes, enabling stable images of moving objects. ! Focus Limit : This distance is approximate value and the focus operate from the setting value. CAUTION: Please avoid continuous, 24-hour use of the auto focus under heavy movement condition.
VT-PTZ Series PROGRAM & OPERATION 4.3 AE CONTROL (MENU => Camera => AE Control) ! Mode : AUTO / MANUAL / SHUTTER / IRIS / BRIGHT AUTO : Auto Iris and Gain, Fixed Shutter speed (NTSC: 1/60 sec, PAL: 1/50 sec) MANUAL : Variable Shutter, Iris and Gain. SHUTTER : Variable Shutter speed, Auto Iris and Gain. IRIS : Variable Iris, Auto Gain and Shutter speed. BRIGHT : Variable Iris and Gain ! Slow Shutter : ON/OFF(AUTO mode only) ! Iris : CLOSE / F28 / F22 / F19 / F16 / F14 / F11 / F9.6 / F8.0 / F6.8 / F5.
VT-PTZ Series PROGRAM & OPERATION 4.4 NIGHT SHOT MENU (MENU => Camera =>Night Shot) The Night Shot option removes the IR Cut filter of the camera and makes the camera sensitive to near infrared. If Night Shot mode of the selected camera is set to Manual, 10+ ON will enable the Night Shot mode, 10+ OFF will turn off the Night Shot mode. ! Mode : MANUAL / AUTO AUTO : Camera automatically goes into B&W mode at low light. MANUAL : Manually controls the Night Shot mode in LOCAL CONTROL option.
VT-PTZ Series PROGRAM & OPERATION 5. TIME/DATE SETUP (MENU => Time & Date) Note: When installing a dome for the first time, the clock doesn’t operate. When you change the time and date, the clock starts to operate. The date and time can be displayed on the monitor when the Date/Time option is set to ON in the display menu. 5.
VT-PTZ Series PROGRAM & OPERATION 5.2 EDIT HOLIDAYS (MENU => Time & Date => Edit Holidays) You can add holidays up to 50. Use the following steps to create a holiday. 1. Select the “NEW” by pushing the joystick to right at the number field. 2. Select the type. Fixed : The holiday occurs on the same date each year. Relative : The holiday occurs on a different date each year, such as the fourth Thursday in November. 3. Select the month, week (relative type only), and day. 4.
VT-PTZ Series PROGRAM & OPERATION Use the following steps to delete the holiday. 1. Select the number to delete. 2. Select “Delete Holiday” and push the Joystick to right. 3. Select “YES” and push the Joystick to right then the next number display at the number field. If no added number, the “NEW” displays at the number field. 4. Repeat step 1 – 3. 5. Select the Exit and pus the Joystick to the right. 5.3 List Holidays (MENU => Time & Date => List Holidays) ! List Holiday : ALL, Each Month 1.
VT-PTZ Series PROGRAM & OPERATION 6. DATA SETUP (MENU => Data Setup) 6.1 FACTORY DEFAULT (MENU => Data Setup => Factory Default) The factory default returns programmed data to initial state as ex-factory except the followings.
VT-PTZ Series PROGRAM & OPERATION 6.2 ERASE PROGRAMMED DATA (MENU => Data Setup => Erase Programmed Data) Erase programmed data in the EEPROM of the selected dome camera. Origin offset value is not affected. 1. Set the option “ON” you want to erase 2. Twist the Joystick to CCW/CW(or move the Joystick to the right or to the left) on the ERASE. CAUTION : Unless you download the data into a safe place, all the data in the selected dome camera will be lost.
VT-PTZ Series PROGRAM & OPERATION 6.4 RESTORE DATA (MENU => Data Setup => Restore Data) This function restores the setting values of the dome of the backup memory to the dome. 6.5 CLEAR DATA (MENU => Data Setup => Clear Data) This function clears all data of the backup memory.
VT-PTZ Series PROGRAM & OPERATION 7. SETUP (MENU => Setup) 7.1 PRESET FREEZE (MENU => Setup => Preset Freeze) ! ON: the image is frozen during calling preset. 7.2 SPEED (MENU => Setup => Speed) User can select preferable speed curves of manual control. (SLOW / MEDIUM / FAST) 7.3 RESPONSE (MENU => Setup =>Response) ! ON : Dome send answer packet after receiving command packet ! OFF: Dome don’t send answer packet after receiving command packet 7.
VT-PTZ Series PROGRAM & OPERATION 7.4.1 FLIP (MENU => Setup =>Dome Angle=>Flip) When the Speed Dome camera is mounted on a ceiling, it can track a moving target in a path directly below the camera: ON : When the camera reaches the moving object directly above the floor, the dome camera tracks the object smoothly with a digitally corrected image. OFF : The dome camera does not perform a flip. 7.4.
VT-PTZ Series PROGRAM & OPERATION This option is used to set the limit of the horizontal view angle so that the trim ring or ceiling does not obstruct the horizontal image when zooming out (wide angle). ON: In some installations it is desirable for the dome camera to be able to see above the horizon. When this option is chosen, the dome will tilt up over the horizon (About - 5 degrees). When the lens is zoomed out, you can see the ceiling line.
VT-PTZ Series PROGRAM & OPERATION 7.6 PASSWORD SETUP (MENU => Setup =>Password) You can change the password with 4-digit character in this menu. The default password is 9999. Edit Password 1. Select the edit password using the joystick. 2. Select the desired number using the joystick up and down, then twist the joystick handle. 3. To protect from recording this password number, select the other number using the joystick up and down by intention. 4.
VT-PTZ Series PROGRAM & OPERATION 7.
VT-PTZ Series SPECIFICATIONS VT-PTZ18W VT-PTZ26 VT-PTZ36W Image Sensor 1/4” Interline Transfer CCD 1/4" Interline Transfer CCD 1/4” Interline Transfer CCD Horizontal Resolution 550 TV Lines 480 TV Lines 550 TV Lines Minimum Illumination 0.7 Lux (1/60 sec) / 0.07 Lux (F1.4 Slow Shutter) 1.0 Lux 50IRE / 0.01 Lux (Night mode w/ ICR on) 1.4 Lux (1/60 sec) / 0.01 Lux (F1.4 Slow Shutter) Lens 4.1~73.8mm @ F1.4 3.5~91mm @ F1.4 3.4~122.4mm @ F1.4 View angle 4.1mm-48º (H) / 73.8mm-2.8º (H) 3.
VT-PTZ Series TECHNICAL SPECIFICATIONS Dimension Figure 16-Dimension ５９
VT-PTZ Series APPENDIX Troubleshooting If problems occur, verify the installation of the camera with the instructions in this manual. Isolate the problem from the equipments in the system and refer to the equipment manual for further information. Problem Solution No video. Verify that power is connected to all components in the system. Verify that the power switches are ON. Check that the BNC connectors are securely connected. Poor video quality. Check the voltage level of the dome camera.
